Main
Copyright Notice
Acknowledgements
Page
SBC-596/599 series comparison table
Refer to the SBC-596/599 features directly in the following manual
Packing list
Contents
Page
Page
Page
Page
Page
Introduction
Features
Specifications
Standard PC system
VGA interface
Mechanical and environmental
Chapter 1 General Information 5
Board layout and dimensions
SBC-596/599 dimensions
Page
Installation Guide
Jumpers
Connectors
Please refer to Appendix B for pin assignment.
Locating jumpers
Locating connectors
Setting jumpers
CPU installation and upgrading
Install a CPU in the ZIF socket
Warning!
Caution!
Voltage Select (J1, J2, J3, and J4)
Chapter 2 Installation Guide 15
Frequency Ratio (J5)
5 6 5 6 5 6 5 6
3 4 3 4 3 4 3 4
J5 Frequency Ratio**
F.R. 1.5*** 2 2.5* 3 J5
MTXC CLK Setting/P55C Enabled (J7)
Clock Setting (J8)
Battery Select and Clear CMOS (J9)
SCSI Select (J10) (SBC-599 only)
ISA Timing (J11) (SBC-599 only)
LCD/EL Select (J13)
Dual Power Select (J15)
Installing DRAM (SIMMs)
Installing SIMMs
Front panel connectors (CN1,CN2,CN3,CN4)
Fan power supply connector (CN5)
SCSI connectors (CN6, CN7)
IDE hard drive connector (CN8, CN9)
Connecting the hard drive
Floppy connector (CN10)
Connecting the floppy drive
VGA interface connections (SBC-599 only)
CRT connector (CN16)
Flat panel connector (CN11)
LCD power select (J12)
Keyboard connectors (CN12, CN19)
COM-port connectors (CN13, CN17)
Printer port connector (CN14)
IR connector (CN15)
USB connectors (CN18, CN20)
Ethernet connector (UTP1, SBC-599 only)
Watchdog timer configurationon
Watchdog select (J14)
Software Configuration
Introduction
Utility with IDE Bus Master Driver
Utility with VGA BIOS (SBC-599 only)
Page
VGA display software configuration
NOTE: ENSURE THAT YOU DO NOT RUN AWDFLASH.EXE WHILE YOUR SYSTEM IS OPERATING IN EMM386 MODE.
Connections for four standard LCDs
Connections to Sharp LM64183P, LM64P89 (640 x 480 DSTN MONO LCD)
*LM64183P -17V LM64P89 -20V
34 SBC-596/599 User's Manual
Connections to PLANAR EL (640 x 480 AD4 EL)
Chapter 3 Software Configuration 35
Connections to Toshiba LTM10C042 (640 x 480 TFT Color LCD)
Pin Pin name Pin Pin name
36 SBC-596/599 User's Manual
Connections to Sharp LM64C142 (640 x 480 DSTN Color LCD)
Pin Pin name Pin Pin name
*external power
Ethernet software configuration
Page
Page
System test and initialization
System configuration verification
AWARD BIOS setup
Entering setup
Load Defaults
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PnP/PCI CONFIGURATION
INTEGRATED PERIPHERALS
Load BIOS defaults
USER PASSWORD
Page
Page
Before you begin
Installation
Simultaneous display mode
Sleep mode
Driver installation
Windows setup
Page
Page
Windows NT Drivers Setup Procedure
Step 2
Step 3
OS/2 Drivers Setup Procedure
Preliminary Steps
Installing from Diskette
Page
Selecting Monitor Type
Selecting Screen Resolution/Refresh Rate
Installation Notes
Page
Installation and Setup
SCSI Configuration Guidelines
SCSI ID Numbers
SCSI Terminators
Page
Page
Installing SCSI Devices
Connecting Internal SCSI Devices
1.
2.
3.
4
5
Configuring the SCSI Adapter
Page
Basic Host Adapter Settings
Boot Device Settings
SCSI Device Settings
Page
Page
Advanced Host Adapter Settings
Note: Several SCSISelect options are not valid unless the host adapter BIOS is enabled.
Page
Using SCSISelect Menus
Using the SCSI Disk Utilities
Installing Device Drivers
ADAPTEC EZ-SCSI UTILITY
Quick Start Instructions
Windows 95 or Windows NT
Troubleshooting Tips SCSI Device Troubleshooting
Windows 95 / Windows NT Troubleshoot- ing
Page
Page
Page
Information for DOS/Windows 3.1x Users
DOS and Windows 3.1x Device Drivers
DOS and Windows 3.1x ASPI Managers
DOS Formatting Utilities
Formatter and Partitioner (afdisk)
Page
Page
Page
A
Programming the Watchdog Timer
B
Pin Assignments
Speaker connector (CN1)
HDD LED connector (CN2)
Reset connector (CN3)
Page
Wide SCSI connector (CN6)
Page
SCSI connector (CN7)
IDE hard drive connectors (CN8, CN9)
* Low active **CN8 IRQ14 CN9 IRQ15
Floppy connector (CN10)
* Low active
Flat panel connector (CN11)
External keyboard connector (CN12)
COM port connectors (CN13: COM2, CN17: COM1)
Printer port connector (CN14)
IR connector (CN15)
CRT connector (CN16)
USB connectors (CN18, CN20)
Keyboard and PS/2 mouse connector (CN19)
Ethernet 10BASE-T connector (UPT1)
Page
Page
* IRQ 0, 1, 2, 8, 13 have been reserved for the system.
IRQ Default Settings
