Adaptec SBC-596, SBC-599 Software Configuration

Chapter 3 Software Configuration 29

CHAPTER

SoftwareConfiguration

This chapter details the software configuration

information. It shows you how to configure the

card to match your application requirements.

AWARD System BIOS is covered in Chapter 4.

Sections include:

• Introduction

• Utility with IDE Bus Master driver

• Utility with VGA BIOS (SBC-599 only)

• VGA display software configuration

• Connections for four standard LCDs

• Ethernet interface configuration

Contents

Main Copyright Notice Acknowledgements Page SBC-596/599 series comparison table Refer to the SBC-596/599 features directly in the following manual Packing list Contents Page Page Page Page Page Introduction Features Specifications Standard PC system VGA interface Mechanical and environmental Chapter 1 General Information 5 Board layout and dimensions SBC-596/599 dimensions Page Installation Guide Jumpers Connectors Please refer to Appendix B for pin assignment. Locating jumpers Locating connectors Setting jumpers CPU installation and upgrading Install a CPU in the ZIF socket Warning! Caution! Voltage Select (J1, J2, J3, and J4) Chapter 2 Installation Guide 15 Frequency Ratio (J5) 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 J5 Frequency Ratio** F.R. 1.5*** 2 2.5* 3 J5 MTXC CLK Setting/P55C Enabled (J7) Clock Setting (J8) Battery Select and Clear CMOS (J9) SCSI Select (J10) (SBC-599 only) ISA Timing (J11) (SBC-599 only) LCD/EL Select (J13) Dual Power Select (J15) Installing DRAM (SIMMs) Installing SIMMs Front panel connectors (CN1,CN2,CN3,CN4) Fan power supply connector (CN5) SCSI connectors (CN6, CN7) IDE hard drive connector (CN8, CN9) Connecting the hard drive Floppy connector (CN10) Connecting the floppy drive VGA interface connections (SBC-599 only) CRT connector (CN16) Flat panel connector (CN11) LCD power select (J12) Keyboard connectors (CN12, CN19) COM-port connectors (CN13, CN17) Printer port connector (CN14) IR connector (CN15) USB connectors (CN18, CN20) Ethernet connector (UTP1, SBC-599 only) Watchdog timer configurationon Watchdog select (J14) Software Configuration Introduction Utility with IDE Bus Master Driver Utility with VGA BIOS (SBC-599 only) Page VGA display software configuration NOTE: ENSURE THAT YOU DO NOT RUN AWDFLASH.EXE WHILE YOUR SYSTEM IS OPERATING IN EMM386 MODE. Connections for four standard LCDs Connections to Sharp LM64183P, LM64P89 (640 x 480 DSTN MONO LCD) *LM64183P -17V LM64P89 -20V 34 SBC-596/599 User's Manual Connections to PLANAR EL (640 x 480 AD4 EL) Chapter 3 Software Configuration 35 Connections to Toshiba LTM10C042 (640 x 480 TFT Color LCD) Pin Pin name Pin Pin name 36 SBC-596/599 User's Manual Connections to Sharp LM64C142 (640 x 480 DSTN Color LCD) Pin Pin name Pin Pin name *external power Ethernet software configuration Page Page System test and initialization System configuration verification AWARD BIOS setup Entering setup Load Defaults STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP PnP/PCI CONFIGURATION INTEGRATED PERIPHERALS Load BIOS defaults USER PASSWORD Page Page Before you begin Installation Simultaneous display mode Sleep mode Driver installation Windows setup Page Page Windows NT Drivers Setup Procedure Step 2 Step 3 OS/2 Drivers Setup Procedure Preliminary Steps Installing from Diskette Page Selecting Monitor Type Selecting Screen Resolution/Refresh Rate Installation Notes Page Installation and Setup SCSI Configuration Guidelines SCSI ID Numbers SCSI Terminators Page Page Installing SCSI Devices Connecting Internal SCSI Devices 1. 2. 3. 4 5 Configuring the SCSI Adapter Page Basic Host Adapter Settings Boot Device Settings SCSI Device Settings Page Page Advanced Host Adapter Settings Note: Several SCSISelect options are not valid unless the host adapter BIOS is enabled. Page Using SCSISelect Menus Using the SCSI Disk Utilities Installing Device Drivers ADAPTEC EZ-SCSI UTILITY Quick Start Instructions Windows 95 or Windows NT Troubleshooting Tips SCSI Device Troubleshooting Windows 95 / Windows NT Troubleshoot- ing Page Page Page Information for DOS/Windows 3.1x Users DOS and Windows 3.1x Device Drivers DOS and Windows 3.1x ASPI Managers DOS Formatting Utilities Formatter and Partitioner (afdisk) Page Page Page A Programming the Watchdog Timer B Pin Assignments Speaker connector (CN1) HDD LED connector (CN2) Reset connector (CN3) Page Wide SCSI connector (CN6) Page SCSI connector (CN7) IDE hard drive connectors (CN8, CN9) * Low active **CN8 IRQ14 CN9 IRQ15 Floppy connector (CN10) * Low active Flat panel connector (CN11) External keyboard connector (CN12) COM port connectors (CN13: COM2, CN17: COM1) Printer port connector (CN14) IR connector (CN15) CRT connector (CN16) USB connectors (CN18, CN20) Keyboard and PS/2 mouse connector (CN19) Ethernet 10BASE-T connector (UPT1) Page Page * IRQ 0, 1, 2, 8, 13 have been reserved for the system. IRQ Default Settings