Manuals / Brands / Computer Equipment / Network Router / ADTRAN / Computer Equipment / Network Router

ADTRAN 1202890E1 Installing the NetVanta VPN Accelerator Card (included in P/N 4200368L1)

1 64

Download 64 pages, 1.13 Mb

Unit Installation NetVanta 4300/4400 Series

54 Copyright © 2013 ADTRAN, Inc. 61200890E2-34R

Installing the NetVanta VPN Accelerator Card (included in P/N 4200368L1)

The optional VPN Accelerator Card plugs into a 32-bit PCI slot and is designed to be used in the

NetVanta4305 to provide encryption/decryption and security acceleration services. The card provides the

following security services to the host processor: DES, triple-DES (3DES), AES, SHA-1, MD5, and

random number generation. Performance metrics include 528 Mbps (DES), 176 Mbps (3DES), and

422 Mbps (AES). The power consumption of the card does not exceed 2 watts.

Figure 23. NetVanta VPN Accelerator Card Installation

The AOS Enhanced Feature Pack software is required to take advantage of the VPN

acceleration features of this card.

The accelerator card is intended to be installed by qualified service personnel only.

Instructions for Installing the VPN Accelerator Card

Step Action

1 Remove power from the unit.

2 Remove the screws holding the base unit and the cover together, and, if necessary, the two

mounting brackets (see Figure 23).

3 Using a 3/16-inch hex driver, remove the two jack screws located on either side of the DB-9 port.

4 Carefully lift and remove the unit’s cover to expose the circuit board.

5 Gently slide the accelerator card into the PCI slot as shown. The card is keyed to fit into the slot

only one way. To avoid damaging the card pins, do not use excessive force.

6 Replace the unit cover, screws, and mounting brackets.

7 Restore power to the unit.

STATUS

NET

WAN

DBU

TD

RD

TD

RD

LNK

LAN 2

NetVanta 4305

ST

A

TUS

ACTIVITY

TEST

WIDE SLOT 1

TD

RD

LNK

LAN 1

NET

WAN

DBU

TD

RD

Contents

Main NetVanta 4300/4400 Series Hardware Installation Guide 61200890E2-34R September 2013 Trademarks To the Holder of the Manual Software Licensing Agreement Page Safety Instructions Save These Important Safety Instructions FCC-Required Information FCC Radio Frequency Interference Statement NetVanta 4300/4400 Series 6 Copyright 2013 ADTRAN, Inc. 61200890E2-34R FCC Radio Frequency Interference Statement Electromagnetic Compatibility (EMC) Table Industry Canada Compliance Information Canadian Emissions Requirements Toll Fraud Liability Service and Warranty Page Table of Contents Page List of Figures Page List of Tables Page 1. INTRODUCTION 2. PHYSICAL DESCRIPTIONS NetVanta 4305 NetVanta 4305 Features and Specifications Network Interface Modules and Dial Backup Interface Modules Supported NetVanta 4305 Shipping Contents NetVanta 4305 Front Panel Design NetVanta 4305 Rear Panel Design The SLOT 3 WIDE MODULE slot accepts the Octal T1/E1 Wide Module. The SLOT 2 NET/DBU and described in the section Option Modules on page 24. Connection directly to an external modem requires a cross-over cable. NetVanta 4430 NetVanta 4430 Features and Specifications Network Interface Modules and Dial Backup Interface Modules Supported SFP Module Slots NetVanta 4430 Shipping Contents Page NetVanta 4430 Rear Panel Design NetVanta 4300/4400 Series Physical Descriptions NetVanta 4300/4400 Series Front Panel LEDs Tabl e 1 describes the front panel LEDs. Table 1. NetVanta 4300/4400 Series LEDs LED Color Indication WIDE SLOT ACTIVITY WIDE SLOT TEST 3. OPTION MODULES Option Module Shipping Contents Page Page Network Interface Modules NetVanta 56K/64K NIM (P/N 1200861L1) NetVanta T1/FT1 NIM (P/N 1202862L1) NetVanta T1/FT1 NEBS NIM (P/N 1200862L2#NEBS) NetVanta T1/FT1 + DSX-1 NIM (P/N 1202863L1) NetVanta Dual T1 NIM (P/N 1200872L1/1202872L1) NetVanta Octal T1/E1 Wide Module (P/N 1202843E1) T1/E1 Mode DIP Switch NetVanta E1/FE1 NIM (P/N 1200868E1/L1) NetVanta E1/FE1 + G.703 Drop NIM (P/N 1200878E1/L1) NetVanta Serial NIM (P/N 1200866E1) NetVanta ADSL NIM, Annex A (P/N 1202869E1) NetVanta ADSL NIM, Annex B (P/N 1202889E1) NetVanta SHDSL NIM, Annex A (P/N 1200936E1) NetVanta SHDSL NIM, Annex B (P/N 1200937E1) NetVanta USB WWAN NIM (P/N 1702803F1) Dial Backup Interface Modules NetVanta Analog Modem DIM (P/N 1200864L1) NetVanta ISDN BRI DIM (P/N 1200865L1) NetVanta ISDN S/T DIM (P/N 1200875L1) 4. UNIT INSTALLATION Tools Required Mounting Options Rack Mounting NetVanta 4300/4400 Series Wall Mounting NetVanta 4300/4400 Series Supplying Power to the Unit NetVanta 4305 (AC) and NetVanta 4430 NetVanta 4305 (DC) Installing Dial Backup and Network Interface Modules Page Using a USB Cellular Modem with the NetVanta USB WWAN NIM Installing the NetVanta VPN Accelerator Card (included in P/N 4200368L1) Installing a SODIMM for Expandable Memory Page Installing a CompactFlash Card Page APPENDIX A. CONNECTOR PIN DEFINITIONS Base Unit Pinouts Connection directly to an external modem requires a cross-over cable. Network Interface Module Pinouts Page Page Dial Backup Interface Module Pinouts (DBU Connector) An optional DIM is required for dial backup applications.