Manuals / ADTRAN / Computer Equipment / Switch

ADTRAN 4200659L5, 4200659L1, 4175043L2, 4200659L8 Load Default Settings, Update FLASH Software

Models: 1200287L1 1200291L1 1200657L2 4200659L4 4200659L6 4200659L3 4200659L7 4200659L2 4200659L8 4200659L5 4175043L2 4200659L1

1 192

Download 192 pages 19.94 Kb

Page 86

Load Default Settings

Chapter 3. Configuration

Load Default Settings

Loading the default settings will disable all STS-1 ports.

Select LOAD DEFAULT SETTINGS from the UTILITIES menu. The screen will display !WARNING! Defaulting configuration will disrupt traffic on all ports. Select CONFIRM to proceed or press Esc to abort.

The IP Address, Default Gateway, and subnet mask will not be reset when default settings are loaded.

Update FLASH Software

Select UPDATE FLASH SOFTWARE from the UTILITIES menu to update software using either XMODEM protocol or Trivial File Transfer Protocol (TFTP).

Update Via XMODEM

Select UPDATE VIA XMODEM from the UPDATE FLASH SOFTWARE

menu; then select 1-STARTto begin the transfer. Once you select 1-STARTfrom this menu, start the XMODEM transfer from your terminal menu program (the XMODEM utility is available under most terminal programs). If you wish to cancel a transfer in progress, press Ctrl-Xthree times.

This function is available only when updating the software through the CRAFT port.

3-40

MX2800 STS-1 User Manual

61200659L1-1

Image 86

ADTRAN 4200659L5 Load Default Settings, Update FLASH Software, Loading the default settings will disable all STS-1 ports

Contents

User Manual MX2800 STS-12001 ADTRAN, Inc All rights reserved Printed in USA Trademark Information901 Explorer Boulevard P.O. Box Huntsville, AL Phone 256 5. This unit contains no user-serviceable parts Canadian Emissions Requirements Federal Communications CommissionRadio Frequency Interference Statement 61200659L1-1Canadian Equipment Limitations Save These Instructions Important Safety InstructionsWarranty and Customer Service LIMITED PRODUCT WARRANTY Post-Sale Support Customer Service, Product Support Information, and TrainingPresales Inquiries and Applications Support Repair and Return TrainingMX2800 STS-1 User Manual 61200659L1-1Chapter 1. Introduction Table of ContentsChapter 2. Installation and Operation Chapter 3. Configuration SNMP Management Options Restore VT Mapping DefaultsTable of Contents Chapter 4. Status Chapter 5. Statistics Acknowledge Alarms ACOSeverely Errored Framing Seconds SEFS Far End STS-1 StatisticsChapter 7. Circuit and Network Redundancy Chapter 6. DiagnosticsChapter 8. Power Loss Recovery Chapter 9. Transaction Language 1 TL1TL1 Responses IndexIndex-1 MX2800 STS-1 User Manual Table of Contentsxviii 61200659L1-1List of Figures Far End STS-1 Statistics Menu List of Tables MX2800 STS-1 User Manual List of Tablesxxii 61200659L1-1Chapter 1 Introduction PRODUCT OVERVIEWController Card 11 Redundancy STS-1 Pointers STS-1 OVERVIEWSTS-1 Framing Virtual Tributaries VT Transport Overhead TOHSTS-1 Synchronous Payload Envelope SPE Unit Timing SNMPAgent TELNETNetwork Manager Page Breakout Panel P/N 1200291L1 Battery Backup P/N 4175043L2AVAILABLE OPTIONS ADTRAN Shipments Include Chapter 2 Installation and OperationUNPACK, INSPECT, POWER UP Receiving Inspection Power Up Chapter 8, Power Loss RecoverySymbol Figure 2-1. DC Power ConnectorTable 2-1. DC Connector Symbol Definitions Battery backup connection. If AC fails, a trap is sent to2. Input Minimum 48 VDC, 0.8 A Minimum 120 VAC, 0.32 A RACKMOUNT INSTALLATION Be sure to install the flanges with the screws providedRear View Connecting the Breakout PanelFront View Figure 2-3. MX2800 STS-1 Rear View REAR PANELFunction LAN Port Noncritical and Critical Alarm ConnectorsConnect the LAN port to intra-building wiring only Modem PortNetwork Interfaces Power ConnectionConnect the DSX-1/E1 interfaces to intra-building wiring only DSX-1/E1 InterfacesFRONT PANEL Craft PortIf you want to Figure 2-5. Terminal Main MenuNavigating Within the Menus PressACO Buttons Status LEDs LED DescriptionsPower Supply A/B Card Condition Table 2-2. LED Conditions for Active CardsLED State These LEDs apply to each individual T1 or E1. Different conditions are indicated by the state of the LED its color and whether it flashes, alternates color, or remains solid. The condition descriptions vary depending on whether the LEDs represent T1s or E1s of the active controller card or the controller card on standby. Table 2-4 on page 2-16 provides LED definitions for the active and standby cards T1/E1 Condition Table 2-4. T1/E1 LED ConditionsLED State ActiveChapter 3 Configuration Figure 3-1. Configuration MenuMX2800 STS-1 User Manual Figure 3-2. Configuration Menu TreeChapter 3. Configuration Figure 3-3. Network Configuration Menu STS-1 ConfigurationNETWORK INTERFACE Line LengthXCV Threshold The unit switches controller cards if Protection ConfigurationSetting VT ModeMiscellaneous Chapter 7, Circuit and Network RedundancyFigure 3-4. VT Interface Menu VT INTERFACEExternal Clock Configuration VT Interface #1-28 T1 Remote Loopback Set MultipleT1 Line Length T1 Circuit ProtectionSet Cross-Connect Mapping Figure 3-6. Set Multiple MenuRestore VT Mapping Defaults Protection ThresholdXCV Threshold Configuration changes to LOCAL IP ADDRESS, GATEWAY IP SYSTEM MANAGEMENTGateway IP Address Management OptionsLocal IP Address Subnet MaskDial String Figure 3-10. Dialup Options Menu Primary and Secondary Phone NumbersInitializing String Maximum Redial AttemptsA trap code indicating the error condition Idle TimeoutConnection Timeout A text description of the faultHangup Modem ModeModem Baud Rate Last Modem ResponseFigure 3-11. Alarm Relay Configuration Menu Alarm RelaysAlarm Relay Configuration Description STS-1 AlarmsAlarm SLM-P AlarmDescription Description VT/Port AlarmsAlarm Alarm DescriptionChapter 3. Configuration System AlarmsAlarm DescriptionAlarm AlarmPower Supply Alarms DescriptionMX2800 STS-1 sends traps SNMP Management OptionsEnter up to five IP addresses of SNMP managers to which the Trap IP AddressesTrap STS-1 Active Alarm TrapsIf enabled, the unit issues a trap when If enabled, the unit issues a trap when TrapTrap STS-1 Standby Alarm TrapsIf enabled, the unit issues a trap when If enabled, the unit issues a trap when TrapTrap If enabled, the unit issues a trap whenVT/Port Traps Trap If enabled, the unit issues a trap whenSystem Traps Trap If enabled, the unit issues a trap whenDISABLED LOS/AISIf enabled, the unit issues a trap when If enabled, the unit issues a trap whenPower Supply Alarm Traps TrapEnter the authentication strings used for SNMP management. Match the MX2800 STS-1 to the SNMP manager for read privileges System Security Date & TimeMiscellaneous These fields allow you to store information that identifies the unitThe system is unusable Shows error conditionsChapter 3. Configuration An action must be taken immediatelyCraft baud rate UTILITIESSave on Logout Then Figure 3-13. System Utilities MenuIf the self test results are Loading the default settings will disable all STS-1 ports Load Default SettingsUpdate FLASH Software Config Transfer Retrieving from a TFTP Server 3. Select SAVE CONFIG REMOTELY3. Select LOAD AND USE CONFIG System Reset SAVE CONFIGURATION3-44 Chapter 3. ConfigurationMX2800 STS-1 User Manual 61200659L1-1Chapter 4 Status Figure 4-1. Status MenuCard A Card A/Card B AlarmsSTS-1 STATE Condition DescriptionNetwork Port Mapping SYSTEM STATE POWER SUPPLY STATEAlarm Card A/Card B exceeded. See Max. Switch Threshold on pageProtection Card CommCurrent Source TIMING STATUSClock Status Chapter 4. Status PRI Ext. ClockSEC Ext. Clock 61200659L1-1VT/PORT STATE Alarm Description cont’dACKNOWLEDGE ALARMS ACO Chapter 5 Statistics Figure 5-2. Local STS-1 Statistics Menu 24 Hour Alarm HistorySTS-1 STATISTICS Description The following alarm counts are provided in this menuCondition Description Figure 5-3. Local STS-1 Current Alarm Count ScreenCondition Figure 5-4. Local STS-1 24-Hour Alarm History Screen Performance Parameters Number of coding violations encountered at the Section layer Path Errored Seconds PES Section Errored Seconds SESLine Errored Seconds LES Section Severely Errored Seconds SSESPath Unavailable Seconds PUAS LOCAL VT STATISTICSLine Unavailable Seconds LUAS Clear All Local STS-1 StatisticsAlarm History Description The following alarm counts are provided in this menuCondition Performance Parameters Figure 5-9. Local VT-LOP Alarm Count Screen Current 15 MinutesFigure 5-10. Local VT-LOP Alarm Count Screen 24 Hour History Coding Violation ConditionDescription Chapter 5. Statistics Figure 5-11. Local VT-CV Performance Parameters Current 15 MinutesFigure 5-12. Local VT-CV Performance Parameters 24 Hour History MX2800 STS-1 User ManualLOCAL PORT STATISTICS Performance Parameters FAR END STS-1 STATISTICSAIS Carrier Alarms Figure 5-14. Far End STS-1 Statistics MenuChapter 5. Statistics Figure 5-15. Far End STS-1 Performance Parameters Current 15 MinutesFigure 5-16. Far End STS-1 Performance Parameters 24 Hour History 61200659L1-1Number of coding violations encountered at the Section layer Path Errored Seconds PES Section Errored Seconds SESLine Errored Seconds LES Section Severely Errored Seconds SSESClear All Far End STS-1 Statistics Line Unavailable Seconds LUASPath Unavailable Seconds PUAS Chapter 5. StatisticsChapter 6 Diagnostics Figure 6-1. Diagnostics MenuFigure 6-2. VT/Port Diagnostics Menu VT/PORT LOOPBACKSTributary Figure 6-4. Analog Network Loopback Analog NetworkFigure 6-3. Tributary Loopback Test Figure 6-5. Digital Line/Network Loopback Digital Line/NetCodec Line/Net Figure 6-6. Codec LoopbackCSU Loopback CSU Loopback w/BERTW/BERT, or a LINE BERT is already active at the time a new CSU VT BERTOnly one T1 port may engage a CSU LOOPBACK, CSU LOOPBACK former test will be terminated and the latter test will be engagedFigure 6-9. Line Bert Test Line BERTFigure 6-8. VT Bert Test Figure 6-10. STS-1 Diagnostics Menu STS-1 LOOPBACKSLine Network Figure 6-12. Analog Loopback Analog LoopbackFigure 6-11. Line Network Test Digital Loopback Figure 6-13. Digital LoopbackMetallic Diagnostics Figure 6-14. Metallic Diagnostics Loopback Test6-12 Chapter 6. DiagnosticsMX2800 STS-1 User Manual 61200659L1-1Chapter 7 Circuit and Network Redundancy NON-REDUNDANT MODE Figure 7-1. Non-Redundant ModeCIRCUIT FAILURE RECOVERY MODE Figure 7-2. Circuit Failure Recovery ModeRecommended Setting CIRCUIT AND NETWORK FAILURE RECOVERY MODETable 7-1. Configuration Requirements for Circuit Recovery Selection PathFigure 7-3. Circuit and Network Failure Recovery Mode 61200659L1-1 Chapter 7. Circuit and Network RedundancyMX2800 STS-1 User Manual Chapter 8 Power Loss Recovery NON-REDUNDANT POWER MODE Power supplies are hot-swappablePOWER SUPPLY RECOVERY MODE Figure 8-2. Power Supply Failure Recovery ModePOWER SUPPLY AND SOURCE RECOVERY MODE This configuration is only available with DC power suppliesBATTERY BACKUP MODE Figure 8-4. Battery Backup System61200659L1-1 Chapter 8. Power Loss RecoveryMX2800 STS-1 User Manual OVERVIEW Chapter 9 Transaction Language 1 TL1INTRODUCTION TL1 MESSAGES TL1 ResponsesCOMPLD - Successful execution of the received command The NTFCNCDE field will contain one of the following values TL1 COMMANDS An asterisk indicates optional command blocks Table 9-1. TL1 CommandsACT-USERusernamepassword ALW-MSG-EQPTrrALLENT-USER-SECUusernamepassword,,privileges Table 9-1. TL1 Commands ContinuedED-USER-SECUusername,password,,privileges DLT-USER-SECUuserRTRV-USER-SECU Table 9-1. TL1 Commands ContinuedRTRV-HDR RTRV-ALM-EQPTrrALLTable 9-1. TL1 Commands Continued TL1 AUTONOMOUS MESSAGES Table 9-2. MX2800 STS-1 Alarm EventsNotification Table 9-2. MX2800 STS-1 Alarm Events ContinuedService ConditionService Table 9-2. MX2800 STS-1 Alarm Events ContinuedService Table 9-3. MX2800 STS-1 Informational EventsError Code TL1 ERROR CODESTable 9-4. TL1 Error Codes Table 9-3. MX2800 STS-1 Informational Events Continued9-14 Chapter 9. Transaction Language 1 TL1MX2800 STS-1 User Manual 61200659L1-1RJ Pin# Appendix A PinoutsTable A-1. Craft Port Pin Assignments DB-9Table A-3. Modem Port Pin Assignments Table A-2. LAN Port Pin AssignmentsDescription DescriptionFunction Table A-4 applies to both the IN and OUT DSX-1/E1 Amp connectorsTable A-4. Amp Pin Assignments 61200659L1-1 Appendix A. PinoutsMX2800 STS-1 User Manual Appendix B Specifications Summary SPECIFICATIONS AND FEATURESANSI T1.107 compatible loopbacks Line loopbacks Power Dimensions 7.86“D x 17.0“W x 1.7“HWeight 5.5 lbs. redundant 4.5 lbs. non-redundant Operating 0 to 50 C 32 to 122 F Storage -20 to 70 C -4 to 158 F61200659L1-1 Appendix B. Specifications SummaryMX2800 STS-1 User Manual Appendix C Acronyms/Abbreviations CSES FEBE PSES data terminal ready 61200659L1-1 Appendix C. Acronyms/AbbreviationsMX2800 STS-1 User Manual ANSI Appendix D Glossary10BaseT asynchronousbipolar bit errorBERT bit ratecarrier channel service unitbyte C-bitdata communications equipment See DCE clockingcraft port data service unit See DSUdelay DLCIethernet end deviceend user facilitiesidle code gatewayhost computer in-bandmonitor Mbpsmodem multi-point circuitout-of-band red alarmremote configuration point-to-pointsignaling serviceservice provider routertransmission Telnettransceiver V.35yellow alarm Numerics IndexPage Page Page