Your ePlatform Partner

User’s Manual for Advantech SOM-A2552 series module V1.00

 

2

 

2.

 

79

nSA_SKT0_IOI

I

IO Select 16. (input) Acknowledge

Pull high with

 

S16

 

from the PCMCIA card that the

10Kohm

 

 

 

current address is a valid 16 bit

 

 

 

 

wide I/O address.

 

80

SA_SKT0_VCC

P

PCMCIA/CF slot 0 power pin.

Powered

81

nSA_SKT1_IOI

I

PCMCIA/CF slot 0 IO Select 16.

Pull high with

 

S16

 

Acknowledge from the PCMCIA

10Kohm

 

 

 

card that the current address is a

 

 

 

 

valid 16 bit wide I/O address.

 

82

nSA_PWR_ON

I

System suspend/wakeup input pin.

Pull high with

 

 

 

Falling edge triggered.

10Kohm

83

nBATT_FALT

I

Main Battery Fault. Signals that

Pull high with

 

 

 

main battery is low or removed.

100Kohm

 

 

 

Assertion causes PXA255

 

 

 

 

processor to enter sleep mode or

 

 

 

 

force an Imprecise Data Exception,

 

 

 

 

which cannot be masked. PXA255

 

 

 

 

processor will not recognize a

 

 

 

 

wakeup event while this signal is

 

 

 

 

asserted. Minimum assertion time

 

 

 

 

for nBATT_FAULT is 1 ms.

 

84

nSW_RESET

I

System software reset input pin.

Pull high with

 

 

 

Falling edge triggered.

10Kohm

85

nVDD_FALT

I

VDD Fault. Signals that the main

Pull high with

 

 

 

power source is going out of

100Kohm

 

 

 

regulation. nVDD_FAULT causes

 

 

 

 

the PXA255 processor to enter

 

 

 

 

sleep mode or force an Imprecise

 

 

 

 

Data Exception, which cannot be

 

 

 

 

masked. nVDD_FAULT is ignored

 

 

 

 

after a wakeup event until the

 

 

 

 

power supply timer completes

 

 

 

 

(approximately 10 ms). Minimum

 

 

 

 

assertion time for nVDD_FAULT is

 

 

 

 

1 ms.

 

86

nRESET_OUT

O

Reset Out. Asserted when

No pulling

 

 

 

nRESET is asserted and deasserts

 

 

 

 

after nRESET is deasserted but

 

 

 

 

before the first instruction fetch.

 

 

 

 

nRESET_OUT is also asserted for

 

 

 

 

“soft” reset events: sleep,

 

 

 

 

watchdog reset, or GPIO reset.

 

87

GND

P

Ground

-

88

PWR_EN

 

Power Enable for the power

Pull high with

 

 

O

supply. (output) When negated, it

100Kohm

 

 

 

signals the power supply to

 

 

 

 

remove power to the core because

 

 

 

 

the system is entering sleep mode.

 

89

BAT_VCC

P

3.0V li-ion coin battery positive

No pulling

19

Page 19
Image 19
Advantech SOM-A2552 manual SASKT0VCC, Pwren, Batvcc