AEG ARE I2 7.1.1 Settings of the Reader / Most Used Parameters

Manual

Page 22 / 33- Revision 01

ARE I2 / RS 232 – Installation Guide

AEG

Identifikationssysteme GmbH

Söflinger Straße 100

D-89077 Ulm

Tel. ++49(0)731-933-1340/1877

Fax ++49(0)731-933-1855

e-mail: info@AEGID.de

Figure 7.1.2 : Software triggered reading operation with TOR>0

Please note: The TOR parameter is only active, if the GT-Command is applied. Within the

time span defined by the value of TOR no NoRead will be output on the interface!

7.1.1 Settings of the Reader / Most Used Parameters

The default operation mode is changed by sending a software command to the reader.

In combination with an R / W transponder, the serial number of the transponder device is read

out only.

MD 2 - triggerd by an software command

most used parameters.

• CID 0 - no suppression of repeatedly read Ids

• CN 0 - no suppression of NoReads

• NID 1 failure protection.; selection guide 2 out 2 transponder codes

• TOR XYZ maximum reading time after the standard read command

is applied to the reader. The chosen value must match the

timing demands of the production process.

TOR 5 Default value

exciter

processor

interface

TOR

GT

reading process

NoRead

reading cycle reading cycle reading cycle

Contents

Main Contents 1 INTRODUCTION 5 2 SYSTEM OVERVIEW 5 3 START-UP PROCEDURE 6 4 INSTALLATION 7 5 VISUAL SIGNAL LAMPS 14 6 SETTINGS OF THE READER / MOST IMPORTANT PARAMETERS 15 7 OPERATING MODES OF THE READER 21 8 INSTRUCTIONS 28 9 HOTLINE 30 10 REFERENCE DOCUMENTATION 30 11 REVISIONS 30 12 APPENDIX 31 Page 1 Introduction 2 System Overview Reader with Integrated Antenna ARE I2 3 Start-up Procedure 4 Installation 4.1 Mounting of the Housing 4.2 Grounding of the Reader 4.3 Assemblage of the Line Connectors 4.3.1 Allowed Diameter of the Used Cables 4.3.2 Assembling of the Cable Pipe 4.3.3 Mounting of the Power Supply Cable ARE I2 / RS 232 Installation Guide 4.3.4 Assembling of the Power Supply and Data Cable (Single Cable Pipe) + green - black 4.3.5 Final Assembly of the Cable Pipe 4.3.6 Plug in of the SAB Cab 1 B 2 A 4.3.7 Using the Service Cable ID 70213 RS232 4.3.8 Using the Power Supply and Data Cable ID 70212 4.4 Power Supply ID ARE I2 5 Visual Signal Lamps 6 Settings of the Reader / Most Important Parameters 6.1 General 6.2 Error Codes 6.3 CID Suppression of ID Codes 6.4 CN Suppression of No Reads 6.5 NID- Failure Protection Page 6.6 EC- Echo 6.7 BD- Baudrate 6.8 TOR Maximum Reading Time 6.9 VS- Show Parameter 6.10 VSAVE Save Parameter 7 Operating Modes of the Reader 7.1 Mode 2 Triggered by an Software Command 7.1.1 Settings of the Reader / Most Used Parameters 7.1.2 Basic Data Exchange Process 7.1.3 ReadOnly-Transponder 7.1.4 R / W Transponder 7.1.4.1 Standard Read Process / Serial Number of the Transponder GT 7.1.4.2 Selective Read RD Example 7.1.4.3 Writing Process WD Example 7.2 Operating Mode 0 - Continuous Reading 7.2.1 Settings of the Reader / Most Used Parameters Page 8 Instructions 8.1 General Instructions 8.2 Special Instructions for Using a Read / Write System 9 Hotline 10 Reference Documentation 11 Revisions ARE I2 / RS 232 Installation Guide 12 Appendix 12.1 Best Orientation for an F-Type -Reader Compact Reader ARE I2 Internal Antenna F-Typ F-Typ-Reading Coil- Best Orientation Disc Transponder 12.2 Best Orientation for an L-Type -Reader Compact Reader ARE I2 12.3 Assembling of the SAB Cab