AEG ARE I2 -

Manual

Page 10 / 33- Revision 01

ARE I2 / RS 232 – Installation GuideAEGIdentifikationssysteme GmbHSöflinger Straße 100D-89077 UlmTel. ++49(0)731-933-1340/1877Fax ++49(0)731-933-1855e-mail: info@AEGID.de

4.3.4 Assembling of the Power Supply and Data Cable (Single Cable Pipe)

The connection of the cable is also done inside of the SAB Cab. Instead of an 2-wire powersupply cable there is now an 5-wire data cable needed. The diameter of the inner wires mustbe big enough to keep the voltage drop in the specified range.The steps to mount the cable is decried in Chapter 4.3.3.

green

-

+

-U

black

shielding

+9..30V

GND (0V)

TXD

RXD

ARE I2

V+

TxD (reader)

GND

RxD (reader)

V+

green-

+

-U

black

shielding

+9..30V

GND (0V)

TXD

RXD

ARE I2

Contents

Main Contents 1 INTRODUCTION 5 2 SYSTEM OVERVIEW 5 3 START-UP PROCEDURE 6 4 INSTALLATION 7 5 VISUAL SIGNAL LAMPS 14 6 SETTINGS OF THE READER / MOST IMPORTANT PARAMETERS 15 7 OPERATING MODES OF THE READER 21 8 INSTRUCTIONS 28 9 HOTLINE 30 10 REFERENCE DOCUMENTATION 30 11 REVISIONS 30 12 APPENDIX 31 Page 1 Introduction 2 System Overview Reader with Integrated Antenna ARE I2 3 Start-up Procedure 4 Installation 4.1 Mounting of the Housing 4.2 Grounding of the Reader 4.3 Assemblage of the Line Connectors 4.3.1 Allowed Diameter of the Used Cables 4.3.2 Assembling of the Cable Pipe 4.3.3 Mounting of the Power Supply Cable ARE I2 / RS 232 Installation Guide 4.3.4 Assembling of the Power Supply and Data Cable (Single Cable Pipe) + green - black 4.3.5 Final Assembly of the Cable Pipe 4.3.6 Plug in of the SAB Cab 1 B 2 A 4.3.7 Using the Service Cable ID 70213 RS232 4.3.8 Using the Power Supply and Data Cable ID 70212 4.4 Power Supply ID ARE I2 5 Visual Signal Lamps 6 Settings of the Reader / Most Important Parameters 6.1 General 6.2 Error Codes 6.3 CID Suppression of ID Codes 6.4 CN Suppression of No Reads 6.5 NID- Failure Protection Page 6.6 EC- Echo 6.7 BD- Baudrate 6.8 TOR Maximum Reading Time 6.9 VS- Show Parameter 6.10 VSAVE Save Parameter 7 Operating Modes of the Reader 7.1 Mode 2 Triggered by an Software Command 7.1.1 Settings of the Reader / Most Used Parameters 7.1.2 Basic Data Exchange Process 7.1.3 ReadOnly-Transponder 7.1.4 R / W Transponder 7.1.4.1 Standard Read Process / Serial Number of the Transponder GT 7.1.4.2 Selective Read RD Example 7.1.4.3 Writing Process WD Example 7.2 Operating Mode 0 - Continuous Reading 7.2.1 Settings of the Reader / Most Used Parameters Page 8 Instructions 8.1 General Instructions 8.2 Special Instructions for Using a Read / Write System 9 Hotline 10 Reference Documentation 11 Revisions ARE I2 / RS 232 Installation Guide 12 Appendix 12.1 Best Orientation for an F-Type -Reader Compact Reader ARE I2 Internal Antenna F-Typ F-Typ-Reading Coil- Best Orientation Disc Transponder 12.2 Best Orientation for an L-Type -Reader Compact Reader ARE I2 12.3 Assembling of the SAB Cab