Manuals / Agilent Technologies / Computer Equipment / Computer Accessories

Agilent Technologies N5700 manual Test Record Form Agilent N5744A and N5764A

Models: N5700

1 132

Download 132 pages 28.95 Kb

Page 104

Appendix B Verification and Calibration

Test Record Form – Agilent N5744A and N5764A

Agilent N5744A and N5764A	Report No _______________		Date __________________
Description	Model	Minimum Specs.	Results		Maximum Specs.
Voltage Programming & Readback
Minimum Voltage Vout	Both	0 mV	__________		+ 50 mV
Measurement Readback	Both	Vout − 20 mV	__________		Vout + 20 mV
High Voltage Vout	Both	19.98 V	__________		20.02 V
Measurement Readback	Both	Vout − 40 mV	__________		Vout + 40 mV
CV Load Effect	Both	− 4 mV	__________		+ 4 mV
CV Source Effect	Both	− 4 mV	__________		+ 4 mV
CV Ripple and Noise
peak-to-peak	Both	N/A	__________		60 mV
rms	Both	N/A	__________		8 mV
Transient Response
Voltage @ 1ms	Both	− 100 mV	__________		+ 100 mV

Current Programming & Readback
Minimum Current Iout	N5744A	0 mA	__________		+ 191 mA
	N5764A	0 mA	__________		+ 381 mA
Measurement Readback	N5744A	Iout − 114 mA	__________		Iout + 114 mA
	N5764A	Iout − 228 mA	__________		Iout + 228 mA
High Current Iout	N5744A	37.924 A	__________		38.076 A
	N5764A	75.848 A	__________		76.152 A
Measurement Readback	N5744A	Iout − 152 mA	__________		Iout + 152 mA
	N5764A	Iout − 304 mA	__________		Iout + 304 mA
CC Load Effect	N5744A	− 12.6 mA	__________		+ 12.6 mA
	N5764A	− 20.2 mA	__________		+ 20.2 mA
CC Source Effect	N5744A	− 5.8 mA	__________		+ 5.8 mA
	N5764A	− 9.6 mA	__________		+ 9.6 mA


Test Description		N5744A Setting		N5764A Setting
Voltage Programming & Readback, Min Voltage		≤40 mV, 152 mA		≤40 mV, 304 mA
Voltage Programming & Readback, High Voltage		20 V, 152 mA			20 V, 304 mA
CV Load Effect, Source Effect, Ripple and Noise		20 V, 38 A			20 V, 76 A
Transient Response		20 V, from 3.8 A to 34.2 A		20 V, from 7.6 A to 68.4 A
Current Programming & Readback, Min Current		152 mA, 20 V			304 mA, 20 V
Current Programming & Readback, High Current		38 A, 20 V			76 A, 20 V
CC Load Effect, Source Effect		38 A, 20 V			76 A, 20 V


Load Requirements		N5744A			N5764A
Current shunt		0.01Ω 100 A			0.01Ω 100 A
Agilent N3300 Electronic load modules		2 – N3305A			3 – N3305A
Fixed Resistor for CV Ripple and Noise		0.53Ω 1kW			0.26Ω 2kW

104	Series N5700 User’s Guide

Image 104

Agilent Technologies N5700 manual Test Record Form Agilent N5744A and N5764A

Contents

User’s Guide Legal Notices Agilent Technologies, IncOn supply Off supply Safety NoticesFrame or chassis terminal This Book Contents 113 116118 124Quick Reference System Features Agilent N5700 DC Power Supplies At a GlanceOutput Features Model Voltage Current Range Programmable FunctionsModel Ratings Front Panel At a Glance LAN indicator OCP indicatorLimit indicator Fine indicatorRear Panel At a Glance J2 Sense Connector SW1 Setup SwitchEnable/Disable control Remote sense + Local sense + Not usedJ1 Analog Programming Connector Installation Accessories General InformationModels Items SuppliedInstalling the Unit Safety ConsiderationsInspecting the Unit EnvironmentThan 6 mm into the sides of the unit Rack InstallationCleaning Connecting the Line Cord Power cord, resulting in fireInput Connections for 750W units Input Connections for 1500W unitsInstallation Wire Size TightenedShorted, whichever is greater For 5 a For 10 a For 20A For 50A For 150AOutput voltage of the power supply Load Connections for 6V to 60V ModelsPrevent loosening the connections or bending the bus-bars Cross Section ResistanceWire Size Load Connections for 80V to 600V Models10 mm 0.39 TorqueLoad wires Output Voltage SensingPlug Type Local SensingRemote Sensing Load Considerations Multiple LoadsOutput Noise and Impedance Effects Inductive LoadsBattery Charging Grounding the OutputThan ±60 VDC above or below chassis ground Shall be more than ±600 VDC above or below chassis groundSetting up the Master Unit Remote SensingSetting up the Slave Units Setting the Over-Voltage ProtectionSetting the Over-Current Protection Series ConnectionsLocal Sensing Separated and floated from each otherJ1 Connector Connections Voltage of the power supplyMating Plug Extraction toolOperating the Power Supply Locally On check-out procedure Turn-On Check-OutBefore Check-Out Constant Voltage CheckOCP Check UVL CheckConstant Current Check Normal Operation Constant Voltage ModeConstant Current Mode CV/CC Mode Crossover CV/CC SignalOver-Voltage Protection Limit the sink current to less than 10mAUnder-Voltage Limit Over-Current ProtectionOver-Temperature Protection Power-Fail ProtectionFront Panel Lock-Out SYSTCOMMRLST, it cannot be unlocked from the front panelOutput On/Off Controls OUT on buttonSafe-Start and Auto-Restart Output Shut-Off TerminalsSW1 switch ENA+/ENA- pins Output Display Prot Indicator Enable/Disable TerminalsSW1 switch SO Signal Level Output Display Power Supply OK Signal Analog Programming of Output Voltage and CurrentDaisy-Chained Output Shut-down Sense terminal, as it may damage the unitAnalog Programming Control Terminals Voltage Programming of Output Voltage and CurrentSW1 switch Down defaultResistance Programming of Output Voltage and Current Voltage Programming Current ProgrammingDown default J1 pin Voltage Monitor Current Monitor External Monitoring of Output Voltage and CurrentPage Operating the Power Supply Remotely Automation-Ready CD-ROM included with this productAutomation-Ready CD-ROM that is shipped with your product Connecting to the InterfacesGpib Interface Visa address is USB023912055serialnumber0INSTR USB InterfaceLAN Interface Connecting to a Site LAN An example of a hostnameConnecting to a Private LAN Previous settingsCAT5 Crossover Cable InstrumentEthernet Connection Monitoring Using the Web ServerLAN Communication Using Telnet Using SocketsConfiguring the LAN Parameters By the subnet mask setting Factory-shipped non-volatile LAN settings Using the Setup UtilityFactory-shipped LAN Settings Series N5700 User’s Guide Syntax Scpi Commands an IntroductionMultiple Commands in a Message Commands from Different Subsystems Message UnitQueries Common CommandsCommand Terminators Parameter Types Numeric ParametersSuffixes and Multipliers Response Data TypesSubsystem is in the Initiated state Scpi Command CompletionDevice Clear Language Reference Scpi Command Description Scpi Command SummarySubsystem Commands Command Description Calibration Commands Commands will generate an errorMeasure Commands CALibrateSTATe Onoff ,password CALibrateSTATe?Output Commands OUTPutSTATe Onoff OUTPutSTATe?Source Commands Model V ratingMin. low limit Max. low limit Status Commands WTG GenerationBit Position Bit Value1024 256 Bit NameSTATusQUEStionableEVENt? 1024 512CLS Bit Position Bit Value 128SRE SRE? ESB = Event status byte summary MAV = Message availableSystem Commands SYSTemCOMMunicateTCPipCONTrol?TST? Trigger Commands ABORtPage Microsoft Excel Microsoft Visual BasicMicrosoft Visual C++ Output Programming Example Series N5700 User’s Guide Trigger Programming Example Series N5700 User’s Guide Page Appendix a Specifications Performance Specifications Agilent Models N5741A N5752A and N5761A N5772ASupplemental Characteristics Programming Resolution Measurement ResolutionRemote Sense Compensation Over-voltage ProtectionSeries and Parallel Capability Savable statesInterface Capabilities Environmental ConditionsOutline Diagram 43.6mmPage Appendix B Verification and Calibration Limits and does not need to be re-calibratedVerification Equipment RequiredPerformance CalibrationPower Supply Measurement TechniquesElectronic Load Current-Monitoring ResistorConstant Voltage Tests Voltage Programming and Readback AccuracyCV Load Effect Model you are checkingCV Source Effect CV NoiseTransient Recovery Time Current Programming and Readback Accuracy CC Load EffectCC Source Effect Test Record Form Agilent N5741A and N5761A Test Record Form Agilent N5742A and N5762A Agilent N5742A and N5762A Report No Date DescriptionTest Record Form Agilent N5743A and N5763A Agilent N5743A and N5763A Report No Date DescriptionTest Record Form Agilent N5744A and N5764A Agilent N5744A and N5764A Report No Date DescriptionTest Record Form Agilent N5745A and N5765A Agilent N5745A and N5765A Report No Date DescriptionTest Record Form Agilent N5746A and N5766A Agilent N5746A and N5766A Report No Date DescriptionTest Record Form Agilent N5747A and N5767A Agilent N5747A and N5767A Report No Date DescriptionTest Record Form Agilent N5748A and N5768A Agilent N5748A and N5768A Report No Date DescriptionTest Record Form Agilent N5749A and N5769A Agilent N5749A and N5769A Report No Date DescriptionTest Record Form Agilent N5750A and N5770A Agilent N5750A and N5770A Report No Date DescriptionUse fixed resistor instead of load modules Test Record Form Agilent N5751A and N5771AAgilent N5751A and N5771A Report No Date Description Test Record Form Agilent N5752A and N5772A Agilent N5752A and N5772A Report No Date DescriptionCalibration Procedure CalibrationVoltage Programming and Measurement Calibration Viattrtmovalue in the ViSetAttribute functionCurrent Programming and Measurement Calibration Appendix C Service Types of Service Available Operating ChecklistTurn-on check out procedure Trouble-shooting guideSymptom Check Does the AC source voltage sag when a load is applied?Error Messages Displaying the Scpi error queueError List ErrorCommand error Syntax errorData type error Command header errorCommand Errors Execution Errors Query ErrorQuery Interrupted Query UnterminatedPage Appendix D Compatibility Result in unpredictable instrument behaviorDifferences In General DifferencesCompatibility Command Compatibility Command SummaryDescription Similar Scpi Command MEASVOLT? Index Initiate commands IndexSpecifications Over-voltage protection130 Series N5700 User’s Guide Safety Manufacturer’sAddress Conforms with the following product standardsManual Updates