Manuals / Agilent Technologies / Computer Equipment / Computer Accessories

Agilent Technologies N5700 manual Tst?

Models: N5700

1 132

Download 132 pages 28.95 Kb

Page 78

5 Language Reference

*IDN?

This query requests the power supply to identify itself. It returns a string of four fields separated by commas.

Agilent Technologies	Manufacturer
xxxxxA	Model number followed by a letter suffix
0	Zero or serial number if available
<A.xx.xx>,<A.xx.xx>	Firmware revision, power supply revision

*OPT?

This query requests the unit to identify any installed options. A 0 indicates no options are installed.

*RCL <state>

	This command restores the power supply to a state that was
	previously stored in memory locations 0 through 15 with the *SAV
	command. Note that you can only recall a state from a location that
	contains a previously-stored state.
	All saved instrument states are lost when the unit is turned off.
NOTE

*RST

This command resets the power supply to a factory-defined state. This state is defined as follows. Note that *RST also forces an ABORt command. The *RST settings are as follows:

CAL:STAT	Off	[SOUR:]CURR:PROT:STAT	Off
INIT:CONT	Off	[SOUR:]VOLT	0
OUTP	Off	[SOUR:]VOLT:LIM	0
[SOUR:]CURR	0	[SOUR:]VOLT:TRIG	0
[SOUR:]CURR:TRIG	0	[SOUR:]VOLT:PROT	MAXimum

*SAV <state>

	This command stores the present state of the power supply to
	memory locations 0 through 15.
NOTE	All saved instrument states are lost when the unit is turned off.

*TST?

This query always returns a zero.

78	Series N5700 User’s Guide

Image 78

Agilent Technologies N5700 manual Tst?

Contents

User’s Guide Legal Notices Agilent Technologies, IncSafety Notices Frame or chassis terminalOn supply Off supply This Book Contents 118 113116 124Quick Reference Agilent N5700 DC Power Supplies At a Glance Output FeaturesSystem Features Programmable Functions Model RatingsModel Voltage Current Range Front Panel At a Glance Limit indicator LAN indicatorOCP indicator Fine indicatorRear Panel At a Glance Enable/Disable control J2 Sense ConnectorSW1 Setup Switch Remote sense + Local sense + Not usedJ1 Analog Programming Connector Installation Models AccessoriesGeneral Information Items SuppliedInspecting the Unit Installing the UnitSafety Considerations EnvironmentRack Installation CleaningThan 6 mm into the sides of the unit Input Connections for 750W units Connecting the Line CordPower cord, resulting in fire Input Connections for 1500W unitsInstallation Shorted, whichever is greater Wire SizeTightened For 5 a For 10 a For 20A For 50A For 150APrevent loosening the connections or bending the bus-bars Output voltage of the power supplyLoad Connections for 6V to 60V Models Cross Section Resistance10 mm 0.39 Wire SizeLoad Connections for 80V to 600V Models TorqueLoad wires Output Voltage SensingLocal Sensing Remote SensingPlug Type Load Considerations Multiple LoadsOutput Noise and Impedance Effects Inductive LoadsThan ±60 VDC above or below chassis ground Battery ChargingGrounding the Output Shall be more than ±600 VDC above or below chassis groundSetting up the Master Unit Remote SensingSetting the Over-Current Protection Setting up the Slave UnitsSetting the Over-Voltage Protection Series ConnectionsLocal Sensing Separated and floated from each otherMating Plug J1 Connector ConnectionsVoltage of the power supply Extraction toolOperating the Power Supply Locally Before Check-Out On check-out procedureTurn-On Check-Out Constant Voltage CheckUVL Check Constant Current CheckOCP Check Constant Voltage Mode Constant Current ModeNormal Operation Over-Voltage Protection CV/CC Mode CrossoverCV/CC Signal Limit the sink current to less than 10mAUnder-Voltage Limit Over-Current ProtectionFront Panel Lock-Out Over-Temperature ProtectionPower-Fail Protection SYSTCOMMRLST, it cannot be unlocked from the front panelSafe-Start and Auto-Restart Output On/Off ControlsOUT on button Output Shut-Off TerminalsEnable/Disable Terminals SW1 switch SO Signal Level Output DisplaySW1 switch ENA+/ENA- pins Output Display Prot Indicator Daisy-Chained Output Shut-down Power Supply OK SignalAnalog Programming of Output Voltage and Current Sense terminal, as it may damage the unitAnalog Programming Control Terminals Voltage Programming of Output Voltage and CurrentResistance Programming of Output Voltage and Current SW1 switchDown default Voltage Programming Current ProgrammingDown default J1 pin Voltage Monitor Current Monitor External Monitoring of Output Voltage and CurrentPage Operating the Power Supply Remotely Automation-Ready CD-ROM included with this productConnecting to the Interfaces Gpib InterfaceAutomation-Ready CD-ROM that is shipped with your product USB Interface LAN InterfaceVisa address is USB023912055serialnumber0INSTR Connecting to a Site LAN An example of a hostnameCAT5 Crossover Cable Connecting to a Private LANPrevious settings InstrumentUsing the Web Server LAN CommunicationEthernet Connection Monitoring Using Telnet Using SocketsConfiguring the LAN Parameters By the subnet mask setting Using the Setup Utility Factory-shipped LAN SettingsFactory-shipped non-volatile LAN settings Series N5700 User’s Guide Scpi Commands an Introduction Multiple Commands in a MessageSyntax Commands from Different Subsystems Message UnitCommon Commands Command TerminatorsQueries Suffixes and Multipliers Parameter TypesNumeric Parameters Response Data TypesScpi Command Completion Device ClearSubsystem is in the Initiated state Language Reference Scpi Command Summary Subsystem CommandsScpi Command Description Command Description Calibration Commands Commands will generate an errorMeasure Commands CALibrateSTATe Onoff ,password CALibrateSTATe?Output Commands OUTPutSTATe Onoff OUTPutSTATe?Source Commands Model V ratingMin. low limit Max. low limit Status Commands WTG Generation1024 256 Bit PositionBit Value Bit NameSTATusQUEStionableEVENt? 1024 512CLS Bit Position Bit Value 128SRE SRE? ESB = Event status byte summary MAV = Message availableSystem Commands SYSTemCOMMunicateTCPipCONTrol?TST? Trigger Commands ABORtPage Microsoft Visual Basic Microsoft Visual C++Microsoft Excel Output Programming Example Series N5700 User’s Guide Trigger Programming Example Series N5700 User’s Guide Page Appendix a Specifications Performance Specifications Agilent Models N5741A N5752A and N5761A N5772ARemote Sense Compensation Supplemental CharacteristicsProgramming Resolution Measurement Resolution Over-voltage ProtectionInterface Capabilities Series and Parallel CapabilitySavable states Environmental ConditionsOutline Diagram 43.6mmPage Appendix B Verification and Calibration Limits and does not need to be re-calibratedPerformance VerificationEquipment Required CalibrationElectronic Load Power SupplyMeasurement Techniques Current-Monitoring ResistorCV Load Effect Constant Voltage TestsVoltage Programming and Readback Accuracy Model you are checkingCV Source Effect CV NoiseTransient Recovery Time Current Programming and Readback Accuracy CC Load EffectCC Source Effect Test Record Form Agilent N5741A and N5761A Test Record Form Agilent N5742A and N5762A Agilent N5742A and N5762A Report No Date DescriptionTest Record Form Agilent N5743A and N5763A Agilent N5743A and N5763A Report No Date DescriptionTest Record Form Agilent N5744A and N5764A Agilent N5744A and N5764A Report No Date DescriptionTest Record Form Agilent N5745A and N5765A Agilent N5745A and N5765A Report No Date DescriptionTest Record Form Agilent N5746A and N5766A Agilent N5746A and N5766A Report No Date DescriptionTest Record Form Agilent N5747A and N5767A Agilent N5747A and N5767A Report No Date DescriptionTest Record Form Agilent N5748A and N5768A Agilent N5748A and N5768A Report No Date DescriptionTest Record Form Agilent N5749A and N5769A Agilent N5749A and N5769A Report No Date DescriptionTest Record Form Agilent N5750A and N5770A Agilent N5750A and N5770A Report No Date DescriptionTest Record Form Agilent N5751A and N5771A Agilent N5751A and N5771A Report No Date DescriptionUse fixed resistor instead of load modules Test Record Form Agilent N5752A and N5772A Agilent N5752A and N5772A Report No Date DescriptionVoltage Programming and Measurement Calibration Calibration ProcedureCalibration Viattrtmovalue in the ViSetAttribute functionCurrent Programming and Measurement Calibration Appendix C Service Turn-on check out procedure Types of Service AvailableOperating Checklist Trouble-shooting guideSymptom Check Does the AC source voltage sag when a load is applied?Error List Error MessagesDisplaying the Scpi error queue ErrorData type error Command errorSyntax error Command header errorCommand Errors Query Interrupted Execution ErrorsQuery Error Query UnterminatedPage Appendix D Compatibility Result in unpredictable instrument behaviorDifferences In General DifferencesCompatibility Command Summary Description Similar Scpi CommandCompatibility Command MEASVOLT? Index Initiate commands IndexSpecifications Over-voltage protection130 Series N5700 User’s Guide Address SafetyManufacturer’s Conforms with the following product standardsManual Updates