Manuals / Brands / Laundry Appliance / Washer / Alliance Laundry Systems / Laundry Appliance / Washer

Alliance Laundry Systems UW35P2, UW35P3, UW60P2, UW60P3 Tutorial Cycle, Enter, Enter, Enter, Enter, Enter, Enter, Enter, High Speed

1 66

Download 66 pages, 1.54 Mb

Programming

24.Press the Enter key. The display flashes “SDLY” for one second.

The display will then read “0M-00S,” allowing the programmer to enter the time for a slow down delay (coast).

At some point in the future–to have the basket coast before it stops, enter the desired coast time (up to 99 seconds). However, do not enter a time now. That would cause a coast before a higher spin speed (which will be the next step).

For no coast, press the Enter key.

25.The next step is to program a high-speed spin.

a.Press the High Speed key once. The display will read “HS1139.”

b.Press the Enter key. The display will read “M---S.”

c.Enter a length of time for the high-speed spin (six minutes). Press key 6. The display will read “6M-00S.”

NOTE: High-speed spin is preceded automatically by medium-speed spin for 30 seconds for nonvariable-speed UW rigid-mount models.

26.Press the Enter key. The display will flash “SDLY” for one second. (“SDLY” also displays during the entire actual coastdown.) The display will then read “0M-00S,” inviting the programmer to enter a time for the slow-down delay (coast). If the application requires that the basket coast before it stops, enter the desired coast time (30 seconds here) and press the Enter key. If no coast is desired, press the Enter key only. The display will read “1239.”

NOTE: A slow-down delay of 30 seconds minimum should be programmed after each high-speed spin. All the preprogrammed and optional cycles in this manual reflect this practice.

27.The previous step ends the tutorial. Cycle 39, consisting of 11 steps, has been completely programmed.

To end the cycle, turn the program mode switch located on the left side of the control module to the RUN position and remove the key. The display will then

read “NEXT.”

The programmer can now select Cycle 39 and press the Enter key to run the cycle, if desired; or a cycle of the programmer’s own design can be programmed.

Tutorial Cycle

Step	Description	Min:sec

1	Hot Fill to Low Level	4:00

2	Supply 1	0:30

3	Wash 1	6:00

4	Drain 1	1:00

5	Warm Spray Rinse	2:30

6	Warm/Warm Fill to High Level	5:00

7	Supply 3	0:30

8	Wash 1	3:00

9	Drain 1	1:00

10	Medium Speed Spin	1:00

11	High Speed Spin	6:00
	SDLY	0:30
	Stop Routine

28

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232090

Contents

Keep These Instructions for Future Reference www.comlaundry.com Page Table of Contents Page Safety Information Explanation of Safety Messages Important Safety Instructions Page Safety Decals Key To Symbols Operator Safety Safe Operating Environment Environmental Conditions Machine Location Input and Output Services Misuse Operation Delivery Inspection Customer Service Serial Plate Location Model Number Familiarization Guide UW60P2OU70001 Machine Familiarization Guide Theory Of Operation Emergency Stop Button WE-6Microcomputer LED Display Display Interpretations UWP_01 DONE DOOR EMTY EXISTS EDIT TEMP OVERHT WATER Operational Keypad Start-up Opening Door Loading Supply Dispenser Cycle Selection Cycle Execution Test Cycle Stop Routine Balance Switch Detection Temperature Display Error Recovery Routine Motor Thermal Overload Indicator Manual Mode Control Feature Programming Programming Keypad Programming Keypad (Continued) Edit Cycle Edit Cycle Add Step Add Step Programming Tutorial spin-spray dilution High Medium Speed Tutorial Cycle Programming Hints CYCLE System Programming Prompting the WE-6 Cycle Programming Displaying a Cycle in Memory Displaying Individual Cycle Usage Editing a Cycle Erasing a Cycle in Memory Step Programming Programming a Fill without Spray Programming a Fill Temperature Fill Temperature Programming Keys Pressed Display Valves Operating Hot + Low + Enter Programming a Supply Step Programming Heat Programming a Wash Step Programming a Wash 5 Thermal Cool-down Programming No Reversing Programming a Soak Step Programming a Drain Step Programming a Flush Step Programming a Spin Step Programming a Rinse Step Programming an Auxiliary Step Simulator Operation and Program Transfer Simulator Operation Transferring All Cycles from Computer to Simulator Transferring One Cycle from Computer to Simulator Transferring All Cycles from Simulator to Computer Transferring One Cycle from Simulator to Computer Preprogrammed Cycles Cycle Categories Standard Supply Legend Standard Cycle Charts Hotels and Motels (Sheets, light soil, cotton/poly blends) (Sheets, light soil, no bleach, cotton/poly blends) (Towels, light soil, cotton) Hotels And Motels (Towels, light soil, no bleach, cotton) (Sheets, medium soil, cotton/poly blends) (Towels, medium soil, cotton) (Blankets, spreads, no bleach) (Blankets, spreads, cold water) (Towels, heavy soil, cotton) (Rinse and spin only) Page (Sheets, heavy soil, cotton/poly blends) (Thermal blankets, bleach, cotton) (Diapers, pads, heavy soil, cotton) (Personals, bleach) (Personals, no bleach) (Pads, polyester) Restaurants (Table napery, bleach, starch, iron) (Table napery, bleach, no iron) (Table napery, colors, no iron) (Visa table napery, bleach, starch, iron) (Visa table napery, bleach, no iron) starch, iron) (Visa table napery, colors, no iron) Shirt Laundries (Shirts, colors, no bleach, starch) (Shirts, bleach, starch) (Shirts, colored, no bleach, no starch) CYCLE (Shirts, no bleach, no starch, delicates) (Starch, extract only) Formula Common to All Markets (Uniforms, with bleach) (Uniforms, without bleach) Formula Common to All Markets (Rags/housekeeping, heavy soil) (Rags/kitchen, mops) (Rewash/reclaim) Cycle 39 (Test)