Allied Telesis 9100, 9101, 9102, 9103

Shelf Mounting Options 9101 Mounting Options

Telesyn 9100 Installation Guide (Installation of Allied Telesyn 9100)

1-10

1.5.1.2 Center Mounting Option - 9101

The bracket is mounted on the center of the 9101 unit as illustrated in Figure 1-5. Mount the bracket following

the steps of Section 1.5.1.1.

FIGURE 1-5 Mid-mount option for 9101

Contents

Main Introduction Who Should Read This Guide? About this Guide Table of Contents Telesyn 9100 Installation Guide (Table of Contents) 1 Installation of Allied Telesyn 9100- - - - - - - - - - - - - - - - - - -1-1 TOC-2 Telesyn User Guide (Table of Contents) 2 Appendix - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-1 1-1 1. Installation of Allied T elesyn 9100 1.1 Installation Overview for the 9100 1.1.1 Allied Telesyn 9100 Configuration 1-2 1.2 Following Procedures for the 9101, 9102, and 9103 1.3 Selecting a Site for the 9100 1-3 1.3.1 9101 Site Requirements Selecting a Site for the 9100 9102/9103 Site Requirements 1-4 1.3.2 9102/9103 Site Requirements Page 1-6 1.4 Setup Checklist 1.4.1 9101 Parts Included in Order 1-7 1.4.2 9102 / 9103 Parts Included in Order 1-8 1.5 Shelf Mounting Options 1.5.1 9101 Mounting Options Page Page 1-11 1.5.2 9102/3 Mounting Options Page 1-13 1-14 1.6 Wall Mounting Option 1.6.1 Overview 1.7 Allied Telesyn 9100 Installation Safety 1-16 1.7.2 Safety Precautions While Working with Electricity 1.7.3 Electrostatic Discharge Page 1.8 Installing Power and Ground for the 9101 1-19 1.8.2 Connect Power and Ground Page 1-21 1.8.3 Connect the -48VDC office power supply to the 9101 PEM plug. 1-22 1.8.4 Connect to Power Source (Single or Dual) 1.8.5 Apply and Check Power (DC Power Supply) 1-23 1.9 Installing Power and Ground for the 9102 1.9.1 Connect Power and Ground 1.9.2 Apply and Check Power (AC Power Supply) 1.10 Alarm Connections - 9101 (Optional) 1-24 1.11 Install Card Modules 1.11.1 Install the CFC12 1-25 1.11.2 Install the Service Module 1.11.3 Install the SFP Module 1.12 Configure Local Terminal or PC 1-27 1-28 1.13 Connect System Cables 1.13.1 Service Modules with RJ21connectors Page Page Data Management Cable (MGMT Port on CFC12) Apply Power and Check Startup Sequence 1-31 1.14 Apply Power and Check Startup Sequence Apply Power and Check Startup Sequence Data Management Cable (MGMT Port on CFC12) Username 6. Input a user ID of officer and a password of officer. 5. The system will run initialization tests and end with the prompt 1-32 : 1-33 1.15 Check the configuration 1.15.1 Check software load 1.15.2 Check management interfaces 1-34 1.16 Adding AC Power Module 1.17 Allied Telesyn Contact Information Page 2-2 2.2 Telesyn 9100 Inventory Form