Information

In Case of Difficulty

If you encounter a problem, turn the power off, then on again. If the unit is still not functioning normally, review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer.

Basic

No function or display.

•Vehicle’s ignition is off.

–If connected following instructions, the unit will not operate with the vehicle’s ignition off.

•Improper power lead (Red) and battery lead (Yellow) connections.

–Check power lead and battery lead connections.

•Blown fuse.

–Check the fuse of the unit; replace with the proper value if necessary.

•Internal micro-computer malfunctioned due to interference noise etc.

–Press the RESET switch with a ballpoint pen or other pointed article.

Radio

Unable to receive stations.

•No antenna or open connection in cable.

–Make sure the antenna is properly connected; replace the antenna or cable if necessary.

Unable to tune stations in the seek mode.

•You are in a weak signal area.

–Make sure the tuner is in the DX mode.

•If the area you are in is a primary signal area, the antenna may not be grounded and connected properly.

–Check your antenna connections; make sure the antenna is properly grounded at its mounting location.

•The antenna may not be the proper length.

–Make sure the antenna is fully extended; if broken, replace the antenna with a new one.

Broadcast is noisy.

•The antenna is not the proper length.

–Extend the antenna fully; replace it if it is broken.

•The antenna is poorly grounded.

–Make sure the antenna is grounded properly at its mounting location.

CD

CD Player not functioning.

•Out of operating temperature range +50°C (+120°F) for CD.

– Allow the vehicle’s interior (or trunk) temperature to cool.

CD playback sound is wavering.

•Moisture condensation in the CD Module.

–Allow enough time for the condensation to evaporate (about 1 hour).

CD insertion not possible.

•A CD is already in the CD player.

– Eject the CD and remove it.

•The CD is being improperly inserted.

–Make sure the CD is being inserted following instructions in the CD Player Operation section.

Unable to fast forward or backward the CD.

•The CD has been damaged.

–Eject the CD and discard it; using a damaged CD in your unit can cause damage to the mechanism.

CD playback sound skips due to vibration.

•Improper mounting of the unit.

–Securely re-mount the unit.

•The disc is very dirty.

–Clean the disc.

•The disc has scratches.

–Change the disc.

•The pick-up lens is dirty.

–Do not use a commercially available lens cleaner disc. Consult your nearest Alpine dealer.

CD playback sound skips without vibration.

•The disc is dirty or scratched.

– Clean the disc; damaged disc should be replaced.

Error displays (built-in CD player only).

•Mechanical error.

–Press . After the error indication disappears, insert the disc again. If the above-mentioned solution does not solve the problem, consult your nearest Alpine dealer.

CD-R/CD-RW playback not possible.

•Close session (finalization) has not been performed.

– Perform finalization and attempt playback again.

MP3/WMA/AAC

MP3, WMA or AAC is not played back.

•Writing error occurred. The MP3/WMA/AAC format is not compatible.

–Make sure the MP3/WMA/AAC has been written in a supported format. Refer to “About MP3/WMA/AAC” on page 14, then rewrite in the format supported by this device.

Audio

The sound is not output from the speakers.

•There is no signal output from the internal amplifier.

–Power IC is switched to “ON” (refer to “Connecting to an External Amplifier” on page 22).

iPod

iPod does not play and no sound is output.

•The iPod has not been recognized.

–Reset this unit and the iPod. Refer to “Initial System Start-Up” on page 8. To reset the iPod, refer to the Owner’s Manual of the iPod.

Indication for CD Player

•No CD is inserted.

–Insert a CD.

•Although a disc is inserted, “No Disc” is displayed and the unit does not start to play or eject the disc.

–Remove the disc by following these steps: Press the button again for at least 2 seconds.

If the disc still does not eject, consult your Alpine dealer.

45-EN