5 Press SOURCE/POWER.
The main menu is displayed.
6 Press 4 (A.PROC).
A.PROC (Audio processor) list display appears.
7 Turn the Rotary encoder to select "TCR/PHASE".
The Function Guide changes.
8 Press 1 (SETUP L/R) or 2 (SETUP L+R).
TCR/PHASE adjustment display appears.
L/R: Different adjustment values can be set for the left and right channels.
L+R:Sets the same adjustment values for the left and right channels.
9 Turn the Rotary encoder to select a speaker to be set.
10 Press the 1 (TIME ; DN) or 2 (TIME UP :) to adjust the time revision value.
11 Press 3 (0°) or 4 (180°) to switch phase.
12 Repeat steps 9 to 11 to adjust other channels.
13 Press 7 (RETURN) to return to the previous display.
•When the speaker is set to the “OFF” mode, the TCR for that speaker cannot be set. Refer to “Setting the Speakers” (page 44).
Graphic Equalizer Adjustments
The graphic equalizer allows you to modify the sound using 31 bands each for the front (left and right), rear (left and right) and center speakers. An additional 10 bands are available for the subwoofer. This allows you to customize the sound to suit your taste.
1 Check that the Defeat mode is off.
2 Press SOURCE/POWER.
The main menu is displayed.
3 Press 4(A.PROC).
The A.PROC (Audio processor) list display appears.
4 Turn the Rotary encoder to select "G.EQ (Graphic EQ)".
The Function Guide changes.
5 Press 2 (ON), then press 3 (SETUP L/R) or 4
(SETUP L+R).
G.EQ adjustment display appears.
L/R: Different adjustment values can be set for the left and right channels.
L+R: Sets the same adjustment values for the left and right channels.
When you do not adjust it, set to OFF.
6 Press the function button of your desired speaker (channel).
The Function Guide changes.
7 Turn the Rotary encoder to select a frequency to be adjusted.
8 Press 1 (LEVEL; DN) or 2 (LEVEL UP :) to adjust the level.
Press 7 (RETURN) to return to the Function Guide in step 6.
9 Repeat steps 6 to 8 to adjust other frequencies.
•When the speaker is set to the “OFF” mode, the graphic equalizer for that speaker cannot be set. Refer to “Setting the Speakers” (page 45).
•Check the playable frequency ranges of the connected speakers before making the equalizer adjustments. If the speaker’s playable frequency range is 55 Hz to 30 kHz, for example, adjusting the 40 Hz or 20 Hz band has no effect. Additionally, you may overload and damage the speakers.
•When graphic EQ is adjusted, the adjustment for parametric EQ becomes ineffective.
Parametric Equalizer Adjustments
The frequency bands of the graphic equalizer are fixed. This makes it very difficult to correct for undesired peaks and dips at specific frequencies. The parametric equalizer’s center frequency can be tuned to these specific frequencies. Then, the bandwidth (Q) and level are
1 Check that Defeat mode is off.
2 Press SOURCE/POWER.
The main menu is displayed.
3 Press 4 (A.PROC).
The A.PROC (Audio processor) list display appears.
4 Turn the Rotary encoder to select "P.EQ (Parametric EQ)".
The Function Guide changes.
5 Press 2 (ON), then press 3 (SETUP L/R) or 4
(SETUP L+R).
P.EQ adjustment display appears.
L/R: Different adjustment values can be set for the left and right channels.
L+R: Sets the same adjustment values for the left and right channels.
When you do not adjust it, set to OFF.
6 Press the function button of your desired speaker (channel).
The Function Guide changes.
7 Turn the Rotary encoder to select a frequency to be adjusted.
8 Press the function button to adjust as follows.
FREQ. ;DN or UP :: Selects the frequency.
LEVEL ;DN or UP :: Adjusts the level.
WIDTH ;DN or UP :: Adjust the band width.
Press RETURN to return to the function guide in step 6.
9 Repeat steps 6 to 8 to adjust other bands.
•When the speaker is set to the “OFF” mode, the parametric equalizer for that speaker cannot be set. Refer to “Setting the Speakers” (page 45).
•It is not possible to adjust the frequencies of adjacent bands within 7 steps.
•Check the playable frequency ranges of the connected speakers before making the equalizer adjustments. If the speaker's playable frequency range is 55 Hz to 30 kHz, for example, adjusting the 40 Hz or 20 Hz band has no effect. Additionally, you may overload and damage the speakers.
•When the parametric EQ is adjusted, the adjustment for graphic EQ becomes ineffective.
