American Standard 6068.26X Roughing-in Dimensions, Recommended Tools Fig, Prior to Installation

Fig. 1 GENERAL DESCRIPTION:

Roughing-in Dimensions			25mm (1) MAX.			SELECTRONIC™
						PROXIMITY TOILET
			FINISHED WALL	MAXIMUM		FLUSH VALVE
	160mm		TOP SPUD	DETECTION ZONE		Concealed Flushometer
				400mm-800mm		for 1-1/2" Spud Fixtures
	(6-1/4)		TOILET	(15-3/4 TO 31-1/2)
						Exclusive, self cleaning piston-type flush
						valve with proximity operation and manual
160mm				127X127mm		override.	Operates on DC (batter y)or
(6-1/4)	OVERRIDE			(5X5 CUTOUT		AC power. Recommended operating
			15˚
	BUTTON			FOR BOX)		pressure 25psi (flowing) to 80 psi (static).
	SENSOR					Can install left or right-handed. Detection
						Zone can also be adjusted manually, or
						with optional remote control.
406mm				EXPOSED BACK
				SPUD TOILET				CONCEALED BACK
(16)	SUPPLY		WALL THICKNESS	432mm		289 TO 403mm		SPUD TOILET
	DN 25mm					(11-3/8 MIN. TO
				(17 MAX.)
	(1) I.P.S.					15-7/8 MAX.)			TOP OF
	-C-L-		51mm (2)	73 TO 111mm					FIXTURE
	115mm-134mm
			+ WALL THICKNESS
	(4-1/2 TO 5-1/4)			(2-7/8 TO		TOP OF		292mm
*-C-L-
				4-3/8)		FIXTURE		(11-1/2) MAX.
152mm	403 TO 441mm
(6) MIN.			73 TO 137mm			19mm
	(15-7/8) MIN. TO
	(17-3/8) MAX.		(2-7/8)MIN. TO			(3/4.)
			(5-3/8) MAX.
		51mm
		(2)
			127mm				51mm		19mm
	TOP SPUD								(3/4.)
		483mm	(5) MAX.					(2)
	TOILET					*FOR LOCATION OF INLET
		(19) MAX.	51mm
						SUPPLY ON BACK INLET
				(2)	FIXTURES,REFER TO FIXTURE
						BEING INSTALLED
			71mm		FOR CORRECT HEIGHT FROM
						FINISHED FLOOR
*Note: The Critical Line (-C-L-) on Vacuum			(2-3/4) DIA.

Breaker must typically be 6" (152mm) min. above fixture. Consult Codes for details.

RECOMMENDED TOOLS;Fig.2

1. Teflon Tape

2.Flat Blade Screwdriver

3.Adjustable Wrench

4.Tape Measure

5.Hacksaw

6.Tubing Cutter

7.File

8.For Sweat Connection; Solder and Torch

9.2.5mm Hex Wrench

10.1.5mm Hex Wrench

Fig. 2
1	2			3
		4
			10'
				6
	5			8
	7		9	10

PRIOR TO INSTALLATION	• Flush all water lines prior to operation (See Step 4). Dirt
Note: Prior to installing the Selectronic™Flush Valve
	and debris can cause flush valve to run continuously.
the following items must be installed.
1. Water Closet	• With the exception of Supply Stop Inlet, DO NOT use pipe
	sealant or plumbing grease on any valve component or
2. Drain line	coupling!
3. Water supply line	• Protect the chrome or special finish on chrome plated
	items.
	DO NOT USE toothed tools on finished surfaces to install or
IMPORTANT:	service these valves. Also see “Care and Cleaning” section
• All plumbing must be installed in accordance with	of this manual.
applicable codes and regulations.	• This product contains mechanical and/or electrical
• Water supply lines must be sized to provide an	components that are subject to normal wear. These
	components should be checked on a regular basis and
adequate volume of water for each fixture.
	replaced as needed to maintain the valve’s performance.
	M968550 REV. 1.5

2