Manuals / American Telecom / Computer Equipment / Modem

American Telecom AM64/128A Injecting 0s, Injecting 1s, Injection Mode, Transparent Mode, Time

Models: AM64/128A

1 55

Download 55 pages 42.17 Kb

Page 24

Test Menu	AM64/128A User Manual

2/ Pattern display

The pattern display usually shows	Injecting 0s

Pressing SELECT will cause binary 1s to be injected (e.g. for loop verification):

Injecting 1s

This pattern will continue to be injected until the SELECT key is pressed again, (or the mode is exited).

3/ Transparency display

The Transparency option is usually disabled, when the display reads:

Injection Mode

Pressing SELECT on this option changes the display to:

Transparent Mode

Binary 0 injection is then disabled and the data path is direct to the DTE or data tester. Selecting Transparent mode changes the pattern display to show:

No Injection

The facility to inject binary 1's remains however. The SELECT key now toggles between no pattern injected and injecting binary 1's.

4/ Time display

The time display simply shows the time since the test has started in seconds.

For example

Time 000010

If the count is stopped the display is	T Stop 000010

Using the transparent mode of the Data Test to test the local interface cable (alternatively a local loop can be used with the local DTE)

24

Image 24

American Telecom AM64/128A manual Injecting 0s, Injecting 1s, Injection Mode, Transparent Mode, No Injection, Time, Stop

Contents

ATL Part No /203/002/610 Issue 4 September Base Band ModemInformation Contained This Document is Confidential to Contents Appendix B Introduction International ModelsConstructional Details Baseband ModemsInterface Modules System Overview System Overview Installation TestingBBM to BBM Link Self Test PassLTU Ready No Alarm LTU Not Ready Link ModeNetwork Mode BBM to Line Card LinkFront Panel Features Menu OperationLoop back Off Loop back OnStatus Menu Over all StatusLoop Active Alarm Status No Alarm No Signal Receiving AIS No AlignmentLOS/CD Fail CD FailUser Rate Line RateInterface Status Operating Mode Link Mode Network ModeTest Menu Local loopLocal loop from menu Top level display shows Loc Loop Off Loc Loop OnLoopback Local loop from DTELoopback is applied by selecting the display Loopback Off Loopback OnRemote Loop Remote Loop from menuRem Loop Off Rem Loop OnBinary Patterns Remote loop from DTEBin Keys Off Sending Bin Error Count Bit Error Rate BER = User Data Rate x Time Data TestOverview OperationErrors nnnnnn Errors s000001Errors Data TestInjection Mode Transparent ModeInjecting 0s Injecting 1sService Test Svc TestComms Evp Rx Evp Tx Time If the count is stopped the display is StopLamp Test Self TestCommunication Channel Loopback Comm Loop OffRate Menu Rate 4.8KMaster 64K BT Slave 4.8K Option Menu 2 X.21bisAsynchronous Mode Signalling Rate3 G.703 Character Length Char LenConfiguration Menu Master SlaveLine Rate 3 X.21 Loop Control ModemSynchronisation Type for software versions below Synchronisation Type for software version V1.3 and above Ext Byte ClkExt Bit Clk Internal Clk5 64k Mode Power LevelMenu Lock Glossary of Terms Band circuits General Specifications Way D type X.21 bis V.24 / V.28* Connector pin allocation Way D-type X.21 V.11 Connector pin allocationAppendix a Interface Pin Connections Mrac Connector Pin allocation Way D-type V.36 Connector pin allocationWay D-type RS-530 Connector pin allocation Line ConnectorAppendix B Internal Link Settings Page Interface Modules Interface ModuleRS530 Interface Module 21bis Interface ModuleService Test Facilities Frame StructureAppendix C In Service Test LVD Safety Statements TTE Network and Safety statementsAppendix E 21 bit timing cable 15 way to 15 way D type plugs21 byte timing cable 15 way to 15 way D type plugs 24 / V.28 bit timing cable 25 way to 25 way D type plugs35 bit timing cable 34 way to 34 way Mrac plugs 21 bis V.36 bit timing cable 37 way to 37 way D type plugs RS530 bit timing cable 25 way to 25 way D type plugsAppendix F Troubleshooting Slave Mode 64K Rate Power 10dBmMaster Mode C 64K Rate Rate 64K