NXR-ZRP Specifications | AMX NXR-ZGW/-ZRP guide

Overview

NXR-ZRP Specifications

The following table outlines the specifications for the NXR-ZRP.

NXR-ZRP (FG5791-02) Specifications

Dimensions (HWD):	• 906 x 2.500 x 3.424 (23.01 mm x 63.50 mm x 86.96 mm) depth does not
	include antenna

Weight:	• 0.25 lbs (113.39g)

Power:	10.5 - 18 VDC; 13.5 (nominal operation voltage)

Memory:	• 16 Mbytes of Flash
	• 1 Megabit external memory

Radio Specifications:
Frequency	IEEE 802.15.4
Operating channels
Operating channels	• 11 - 26
Modulation technique
Modulation technique	• DSS
Output power
Output power	• Region/country specific
Coverage area
Coverage area	165 feet (502.m)

Firmware/Software
Specifications:
Communications	The NXR-ZRP communicates with a Netlinx master via a NXR-ZGW. The
	NXR-ZGW communicates with a Netlinx master over TCP/IP encapsulating the
	ICSP protocol via a physical Ethernet connection. The ICSP device number
	can be set via the browser-based management system.
Front Components:
Front Components:
LEDs	• PWR/STATUS - A green LED that blinks to indicate the device is
	programmed and communicating properly. Power ON, but no master
	connection, is indicated with a solid light; Power OFF is indicated with no
	light.
	• ICSP - The LED is solid when ICSP connection is in place with the NetLinx
	master.
	• RF - The LED is solid when end devices are connected; end devices not
	connected is indicated with no LED light; the LED blinks to indicate activity.

Antenna Mount	A reverse SMA connection that supports a 2.4GHz antenna.

Reset Button	Press and hold for approximately 10 seconds to return the NXR-ZRP to factory
	default settings.

Rear Components:
Power connector	• 2-pin 3.5mm Phoenix connector

Certifications:	• FCC ID: CWU-ZRD
	• IC ID: 5088A-ZRD
	• CE
	• IEC-60590
	• TELEC

Operating/Storage	• Operating Temperature: -30°C (-22°F) to 70°C (158°F)
Environments:	• Relative Humidity: 5% to 85% non-condensing; intended for indoor use only


Included Accessories:	• 2.4GHZ, MONO, RSMA, 3.5IN, 2.0DBI Antenna (70-0012-SA)
	• Rubber feet
	• Velcro mounting strip
	• Power Supply (24-5791-SA)

NXR-ZGW/-ZRP	3

Image 9

AMX NXR-ZGW/-ZRP manual NXR-ZRP Specifications, NXR-ZRP FG5791-02 Specifications

Contents

NXR-ZGW/-ZRP AMX Limited Warranty and Disclaimer Software License and Warranty Agreement Page Table of Contents Device Configuration NXR-ZGW Specifications NXR-ZGW FG5791-01 SpecificationsOverview NXA-WAP 2403A 3 dBI Antenna FG2255-20 NXR-ZRP FG5791-02 Specifications NXR-ZRP Specifications Front and Rear Components of the NXR-ZRP Network structure How ZigBee works Single PAN ID installations Multiple PAN ID installationsMesh Network Arrangements Multiple PAN ID Network FCC Compliance NXR-ZGW/-ZRP Installation Things to Consider Before StartingLocation and Antenna Direction Connecting Power to the NXR-ZGW and NXR-ZRP Connecting the NXR-ZGW to a LANConnecting the Optional Accessory Antennas Determining the Power Source Table top installation of the NXR-ZGW and NXR-ZRP Using the PSN NetLinx connector for powerRack mounting the NXR-ZGW and NXR-ZRP NXR-ZGW/-ZRP Setting up a Network NXR-ZGW/-ZRP NXR-ZGW Browser-based Configuration Manager Pages Summary of Gateway SettingsSummary Determining the PAN settings of the NXR-ZGW Determining the IP settings of the NXR-ZGWRebooting the Configuration Manager Checking the firmware version Network IP Settings ConfigurationSetting the IP Address IP Address User Settings Setting the DNS AddressSetting a new username and password User Settings Connecting an NXR-ZRP to the network for the first time Enabling and disabling the wireless networkPersonal Area Network PAN Network Connecting a Repeater to the Gateway Setting the PAN channel Finding a device’s EUI address ConnectionsFinding the device’s description Determining the device type Checking the device link status Determining the device link quality PAN Device Details PAN Device Details Removing a device from the Access List Putting a device on the Access ListLocating the device Changing a Connected Device description Changing a device’s ZigBee networking information Allowing firmware updates to all devices on a network Allowing firmware updates to individual devicesUtilities Device Firmware Determining the connection status of a device Connection LogFinding the device’s Icsp number Connection Log Traffic Log Traffic Log Finding the device traffic NXR-ZGW/-ZRP Before beginning the Upgrade process Device ConfigurationSending Firmware to The NXR-ZGW Upgrading The NXR-ZGW via An IP Address Verifying and Upgrading the device firmware via an IP Assigning Communication Settings and TCP/IP Settings Select the device’s firmware file from the Files section FIG Using the ID Button to Change the NXR-ZGW’s Device Number NXR-ZGW/-ZRP It’s Your World Take Control