Figure D-7 | Anritsu 0701012, MA24106A instruction

Upgrading the Firmware

Upgrading the Firmware

7.Click Program Device. The following messages will be displayed during the program operation:

MESSAGE - Programming FLASH Completed MESSAGE - Erasing and Programming FLASH...

Figure D-6.Firmware Upgrade Application

8.Disconnect and reconnect the USB cable from the power sensor, and then click OK to complete the firmware upgrade procedure.

Figure D-7.

9.Launch the Anritsu Power Meter application to begin using the upgraded sensor.

D-4	MA24106A UG

Image 66

Anritsu 0701012, MA24106A manual Figure D-7

Contents

MA24106A USB Power Sensor User Guide True-RMS, 50 MHz to 6 GHz Updates Anritsu Company Software License Agreement Page Table of Contents Table of Contents General Information Preparation for Storage/Shipment Preparation for Storage/Shipment Installation Driver InstallationHardware and Software Requirements Driver Installation Anritsu Power Meter Installation Installation Driver Installation License Agreement Software will then install to the selected location Found New Hardware Wizard Select the hardware type Computer, and then click Next Click Have Disk..., and then click Next 14.Found New Hardware Wizard Click Finish to close the wizard Page Using the Power Sensor Graphical User Interface Buttons Using the Power Sensor ButtonsData Entry Fields Using the Power Sensor Display Window Display WindowStatus Bar File Menu Menu Bar Using the Power SensorMenu Bar Tools Menu Data Logging Menu DataLogging Menu Power Graph 10. Data Logging Time, X-axis 30 minutes Offset Table 14.Offset Entry Screen 16. Open Dialog MA24106A UG Session Restore 17.Offset Table Menu Offset Table Off Status Using the Power Sensor Making Measurements Basic Power MeasurementConnecting the DUT Making Measurements Calibrating the Sensor Making Measurements Using the Power SensorZeroing the Sensor Applying a Calibration Factor Correction Number Averages Needed for ±0.20 dB ±0.15 dB ±0.10 dB ±0.05 dB ±0.01 dB DBm Noise Measurement Considerations Using the Power Sensor Error StatesTime Varying Signals Message Description Resolution Using the Power Sensor Measurement Considerations High Crest Factor Signals peak to average ratioMultitone Signals Noise and Averaging Settling Time Using the Power Sensor Uncertainty of a Measurement Uncertainty of a Measurement Uncertainty Example Uncertainty of a Measurement Using the Power SensorUncertainty Adjusted Specification Noise Calculations at 12 dBm 16 mW Remote Operation Commands Summary Command DescriptionRemote Operation Remote Operation Command Details Remote Operation Command Details Remote Operation Remote Operation Command Details FREQ? HAT Sensor Operational Tests Required Equipment Test Procedure Vswr PretestVswr Pretest Sensor Operational Tests Calibration Factor Test Sensor Operational Tests Calibration Factor Test Calibration Factor Test Sensor Operational Tests MA24106A Linearity Test Sensor Operational Tests Linearity Test Linearity Test Sensor Operational Tests Apply Sensor Operational Tests Linearity Test +20 +15 +10 Adjust per Max Min Delta E11 E12 Measurement Results 2 GHz Measurement Results 6 GHz Appendix a Connector Care and Handling Beware of destructive pin depth mating connectors Cleaning connectors Avoid over torquing connectorsAvoid applying excessive power Connector Care and Handling Using the Demo Application Appendix B Sample Visual Basic CodeDemo Application Using the Demo Application Sample Visual Basic Code Sample Visual Basic Code Using the Demo Application Delay routine For Anritsu Power Meter 1.0 Only Appendix C Serial Port Compatibility Method 1-Download Updated Software Method 3-Remapping a Serial Port Serial Port Compatibility Figure C-2.System Properties Method 3-Remapping a Serial Port Figure C-3.Device Manager Figure C-4.Advanced Settings for COM Port Close all windows that you have opened up to this point Appendix D Upgrading the Firmware Upgrading the Firmware Figure D-3.Firmware Upgrade Dialog Upgrading the Firmware Figure D-5.Open File Dialog Figure D-7 Symbols Symbols to LIndex To S Index-2 MA24106A UG To Z USB