Caller ID Feature Setup, Caller ID with Call Waiting | AT&T 9370

9370_to make pdf_1ATT 6/12/00 2:06 PM Page 9

FEATURE SETUP

Caller ID Feature Setup

You can set up Caller ID features at the handset right after setting up the final Telephone feature (Handset Ringer), by programming your Home Area Code. Otherwise, follow Steps 1-4in “Telephone Feature Setup” on page 8 to begin setting up Caller ID features.

Program Home and Local Area Codes

Your “home area code” is usually the area code from which you are dialing. “Local area codes” are area codes for which you must dial an area code but not “1.” Always program your home area code, and, if you need them, up to four local area codes to allow for correct operation of the Display Dial feature (see page 39).

NOTE: Do not select CHANGE. Instead, when screen displays AREA CODE 1:

1Use the keypad to enter your home area code (AREA CODE 1).

2Select CODE 2 to reach AREA CODE 2 (the screen displays any current local area code stored here). Use the keypad to enter a three-digit local area code.

3Continue as in Step 1 for area codes 3, 4 and 5 as needed.

4Select DONE when finished.

AREA	CODE 1:000
CODE	2	DONE

Caller ID with Call Waiting

You must subscribe to Caller ID with Call Waiting service (a combined service) in order for this feature to work. If you don’t have Caller ID with Call Waiting service, turn this feature off.

CIDCW: ON

CHANGE DONE

CIDCW: OFF

CHANGE DONE

Call List Options

Choose whether the system stores information about ALL CALLS received, or for NO CALLS.

LIST:ALL CALLS

CHANGE DONE

LIST:NO CALLS

CHANGE DONE

9

Image 11

AT&T 9370 Caller ID Feature Setup, Program Home and Local Area Codes, Caller ID with Call Waiting, Call List Options

Contents

Revised 6/12/00 Advanced American Telephones. All rights reserved Contents Page About Home and Local Area Codes Before YOU BeginAbout Caller ID with Call Waiting Before You Install Installation Install the handset battery Table/Desk and Wall Installation Connect the telephone line cord Softkeys Feature SetupMessage Window Display for Feature Setup Handset Ringer Telephone Feature SetupDial Mode Handset Ringer Off / Battery Save Call List Options Caller ID Feature SetupProgram Home and Local Area Codes Caller ID with Call Waiting Answering System Feature Setup Audible Message Alert Select Your AnnouncementRing Select / Toll Saver Change Priority Calling Code Change Remote Access CodePriority Call Signal Record Your Announcement from the Base Review Feature Settings Set the Clock Delete an Announcement Talking Caller ID Feature Setup Caller Specific Outgoing Announcement Feature Setup Announcements Outgoing Local Review ADD Enter Number Done Menu Call ID DIR Directory MEM ANS SYS Delete Done Telephone Operation Mute RedialTemporary Tone Record a Phone Conversation HoldIntercom Headset Jack Changing Channels AT the Base Speaker Base Ringer Volume Handset Locator Page/Intercom Store a Number in Memory Telephone MEMORY/DIRECTORY Replace a Stored Number Store a Pause in a Memory NumberStore a Name with a Memory Number View Memory Numbers Store a Number and Name from Call History Edit Memory Numbers Delete Memory Numbers Dial a Memory Number from the Base Priority Ring NumbersDial a Memory Number from the Handset Announcement Play/Silent Audible IndicatorsAnswering System Operation About Mailboxes Record a Memo Answering CallsCall Screening/Intercept Announcement Bypass Function Button Listen To, Save & Delete Messages CL ↔ AO Message Window Display From a Touch Tone Phone Call ScreeningConnect with the Answering System From the Cordless Handset Function Command Remote Access Commands End remote access call Voice Help Menu Audible Signals Memory Match Call WaitingIncoming Call History Display Dial Caller ID OperationReview Call History Delete a Specific Call Record Delete Call Records from Call History Delete All Call Records Caller ID Display Messages Operating Range Batteries Battery LifeCharge the Handset Battery Pack Batteries Replace the Handset Battery Pack To re-initialize the handset and base Case of DifficultyIf the phone does not work at all, check these items first If you have no dial tone If the caller’s name or phone number is not displayed If you hear noise or interference when using the phoneIf the phone does not ring when you receive a call If you have difficulty hearing messages If speakerphone conversation sounds distortedIf messages are incomplete If your outgoing announcement isn’t clear If CL appears in the Message Window Index Index Answering System Remote Commands Remote Command Press