Manuals / AT&T / Communications / Cordless Telephone

AT&T 9370 user manual Review Feature Settings, Record Your Announcement from the Base

Models: 9370

1 55

Download 55 pages 44.35 Kb

Page 15

9370_to make pdf_1ATT 6/12/00 2:06 PM Page 13

FEATURE SETUP

Review Feature Settings

Check the status of the answering system feature settings by pressing

9(SETUP) on the base.

Record Your Announcement from the Base

•You can record up to three different announcements — A, B, and AO

— that callers will hear when the system answers a call. Each announcement can be up to three minutes long.

•Announcements A and B are used when you want the system to record callers’ messages. Announcement AO (Announce Only) is used when you want to give information to callers without accepting messages.

•If you choose not to record an announcement for A or B, the system answers with a prerecorded announcement: “Hello. Please leave a message after the tone.” The system does not have a prerecorded announcement for AO.

•For Announcements A and B, make sure you indicate in your announcement who has been assigned to each mailbox, and that callers should press 1or 2to access the appropriate mailbox.

NOTE: For best sound quality, record your announcement from the cordless handset (see “Remote Access Commands” in ANSWERING SYSTEM OPERATION At Cordless Handset or Touch Tone Phone on page 35).

1If the announcement you want to record is the currently selected announcement (A, B, or AO) go to Step 2. If not, select the announcement by following the instructions in “Select Your Announcement” on page 11, then go to Step 2 below.

2Press *(CHANGE) on the base.

3Press 7(ANNC) .

4At the prompt, begin recording your announcement. Speak in a normal tone of voice, about nine inches from the microphone.

5When you are finished, press Xor x. If the announcement did not record successfully, you’ll hear an error tone. Record the announcement again.

To review the announcement at any time, press 7(ANNC).

NOTE: The total recording time for this system is about 12 minutes. Since all messages, memos, and announcements contribute to that time, a short outgoing announcement is recommended.

13

Image 15

AT&T 9370 user manual Review Feature Settings, Record Your Announcement from the Base

Contents

Revised 6/12/00 Advanced American Telephones. All rights reserved Contents Page Before YOU Begin About Caller ID with Call WaitingAbout Home and Local Area Codes Before You Install InstallationInstall the handset battery Table/Desk and Wall InstallationConnect the telephone line cord Feature Setup Message Window Display for Feature SetupSoftkeys Handset Ringer Telephone Feature SetupDial Mode Handset Ringer Off / Battery SaveCall List Options Caller ID Feature SetupProgram Home and Local Area Codes Caller ID with Call WaitingAnswering System Feature Setup Select Your Announcement Ring Select / Toll SaverAudible Message Alert Change Remote Access Code Priority Call SignalChange Priority Calling Code Record Your Announcement from the Base Review Feature SettingsSet the Clock Delete an AnnouncementTalking Caller ID Feature Setup Caller Specific Outgoing Announcement Feature SetupAnnouncements Outgoing Local Review ADD Enter Number Done Menu Call ID DIR Directory MEM ANS SYS Delete Done Telephone Operation Redial Temporary ToneMute Hold IntercomRecord a Phone Conversation Headset Jack Changing ChannelsAT the Base Speaker Base Ringer VolumeHandset Locator Page/IntercomStore a Number in Memory Telephone MEMORY/DIRECTORYStore a Pause in a Memory Number Store a Name with a Memory NumberReplace a Stored Number View Memory Numbers Store a Number and Name from Call HistoryEdit Memory Numbers Delete Memory NumbersPriority Ring Numbers Dial a Memory Number from the HandsetDial a Memory Number from the Base Announcement Play/Silent Audible IndicatorsAnswering System Operation About MailboxesRecord a Memo Answering CallsCall Screening/Intercept Announcement BypassFunction Button Listen To, Save & Delete MessagesCL ↔ AO Message Window DisplayFrom a Touch Tone Phone Call ScreeningConnect with the Answering System From the Cordless HandsetFunction Command Remote Access CommandsEnd remote access call Voice Help Menu Audible SignalsCall Waiting Incoming Call HistoryMemory Match Caller ID Operation Review Call HistoryDisplay Dial Delete a Specific Call Record Delete Call Records from Call HistoryDelete All Call Records Caller ID Display MessagesOperating Range Battery Life Charge the Handset Battery PackBatteries Batteries Replace the Handset Battery Pack To re-initialize the handset and base Case of DifficultyIf the phone does not work at all, check these items first If you have no dial toneIf you hear noise or interference when using the phone If the phone does not ring when you receive a callIf the caller’s name or phone number is not displayed If speakerphone conversation sounds distorted If messages are incompleteIf you have difficulty hearing messages If your outgoing announcement isn’t clear If CL appears in the Message WindowIndex Index Answering System Remote CommandsRemote Command Press