Battery installation and charging, Step | AT&T ATTCL83201 specs

Getting started

Battery installation and charging

Install the battery as shown below. Once you have installed the battery, the screen indicates the battery status (see the table below). If necessary, place the handset in the telephone base or charger to charge the battery. For best performance, keep the handset in the telephone base or charger when not in use. The battery is fully charged after ten hours of continuous charging. See the table on page 110 for battery operating times.

If the screen shows Place in charger and flashes, you need to charge the handset without interruption for at least 30 minutes to give the handset enough charge to use the telephone for a short time. The following table summarizes the battery charge indicators and actions to take.

Battery indicators	Battery status	Action

The screen is blank, or	Battery has no or very	Charge without interruption
shows Place in charger	little charge. The handset	(at least 30 minutes).
and (flashing).	cannot be used.

The screen shows	Battery has enough charge	Charge without interruption
Low battery and	to be used for a short time.	(at least 30 minutes).
(flashing).

The screen shows	Battery is charged.	To keep the battery charged,
HANDSET X.		place it in the telephone base or
		charger when not in use.

NOTE: If you are on a phone call in low battery mode, you hear four short beeps every minute.

BT183342/BT283342BY 1021

Step 1

Plug the battery connector securely into the socket inside the handset battery compartment. Insert the supplied battery with the label THIS SIDE UP facing up as indicated.

Step 2

Align the cover flat against the battery compartment, then slide it upwards until it clicks into place.

Image 13

AT&T ATTCL83201 user manual Battery installation and charging, Step

Contents

Complete user’s manual Congratulations Abridged user’s manual Parts checklist Table of contents Multiple handset use Index Quick reference guide handset QCID/VOLUME Main menu Quick reference guide telephone base Cancel MENU/SELECT Answer on Avoid placing the telephone base too close to Installation Telephone base installation Telephone base and charger installationCharger installation Step Battery installation and charging Charge light Step Tabletop to wall mount installation Installation options Wall mount to tabletop installation Setting Handset settings Ringer tone Ringer volume To set the date and time manually Set date/time LCD language To turn on or off the caller ID announce featurePress MENU/SELECT to choose LCD language Set English/Français/Español as LCD language? Save your speed dial voicemail number Voicemail visual message waiting indicatorTo save your voicemail number Clear voicemail indication To manually turn off the new voicemail indicators Key tone Rename handset Home area code Use caller ID to automatically set date and timeTo set the home area code Only for 7 digit dial from CID To set the dial mode Dial modeWebsite Telephone base settings Ringer Volume MENU/SELECT, or enter the number using the dialing Or Español Base Use this feature when the telephone indicates there is Rename base Press MENU/SELECT. The screen briefly shows Use qCID or pDIR to highlight Tone or Pulse, then Telephone operation Using the telephone base Press /SPEAKER Auto off Ending a call Using a cordless handsetTemporary ringer silencing Using a cordless handset Last number redial Handset speakerphoneTo view the ten most recently dialed numbers To delete a redial entry Using a cordless handset To redial a number Using a cordless handset Equalizer Options while on calls Volume control Using a cordless handsetCall waiting Using the telephone base To mute a call Using a cordless handset To mute a callMute To end mute a call To access the redial list while on a call To access the caller ID log while on a callChain dialing Temporary tone dialing To transfer an outside call from a handset Blind transferPress MENU/SELECT to choose Transfer Transfer from Base 0 Base represents To transfer an outside call from the telephone base Handset locator Multiple handset useTo start the paging tone To stop the paging tone Intercom Calling Handset Press MENU/SELECTCalling Handset X or Calling all handsets Calling or Base 0 is calling all Transfer . The handset shows Call transferred . Call transfer using intercom Push-to-talk PTT Turn PTT on or off Using a cordless handset Handset shows Connecting to Handset PTT call to a single device Using a cordless handset Telephone base shows Connecting to Handset Connecting to group To call multiple devices Using a cordless handsetPTT call to multiple devices Answer a PTT call Answer an incoming call during a PTT call Change a one-to-one PTT call to an intercom call End or leave a PTT call Make an outgoing call during PTT call Shared directory About the directoryCapacity Create a new directory entry Create directory entries Add a predialed telephone number to the directory Review directory entries Review the directory Search by name Search the directory Dial, delete or edit directory entries Delete a directory entry Using a cordless handsetDisplay dial Edit a directory entry Assign a speed dial number Speed dialAssign your voicemail speed dial number Delete a speed dial number Reassign a speed dial numberDial. Press Check your voicemail using speed dial Make a call using speed dial Information about caller ID with call waiting About caller ID Caller ID history Missed new call indicatorHow the caller ID history caller ID log works Memory match Caller ID operation Beginning or end of the caller ID log Review the caller ID history Dial a caller ID log entry View dialing optionsDelete caller ID log entries To delete an entry To delete all entries Save a caller ID log entry to the directory On-screen message Reason Reasons for missing caller ID information Announcement Answering system settingsPress MENU/SELECT to select Play annc MENU/SELECT to enter the main menu Answering system settings ANS on Answer on/off Call screening To change the setting Using a cordless handsetPress MENU/SELECT to select Call screening Number of rings To set the number of rings Using a cordless handsetToll saver To change the remote access code Remote access code Message alert tone Message recording time Using the answering machine and voicemail together Answering system and voicemail indicatorsAbout the answering system Voice prompts Message capacityCall screening To screen a call at the telephone base Call intercept To screen a call at the handsetBase ringer Temporarily turning off the message alert tone To listen to messages at the telephone base Message playbackPlay old msgs, then press MENU/SELECT or /PLAY/STOP To listen to messages on a cordless handset When messages are playing on the handset When messages are playing on the telephone baseOptions during playback To delete all old messages on the telephone base Delete all old messagesDelete all old messages? To delete all old messages on the handset Recording and playing memos Record a memo Using a cordless handsetPlay back a memo Message counter displays Base message counter displays Remote commands Remote accessTo remotely reach your answering system Remote access Register a handset to the telephone base Adding and registering handsets/headsetsRegistering... Please wait and the in USE light on Press and hold /HANDSET Locator on Deregistering handsetsIt shows Deregister all devices? Release /HANDSET Locator Handset screen icons Alert tones and lightsTelephone base screen icons Telephone base alert tones Handset alert tones USE Lights Screen messages Screen display messages Transfer to Display screen messages My telephone doesn’t work at all TroubleshootingCannot get a dial tone Cannot dial out Batteries do not hold a charge My cordless handset isn’t performing normally My cordless handset does not ring when I receive a call Hear other calls while using my phone My calls cut in and out while I’m using my cordless handset Charge light is off or blinking System does not receive caller ID when on a callMy caller ID isn’t working Incomplete messages Difficulty hearing messages System does not respond to remote commandsSystem does not answer after the correct number of rings Outgoing announcement is not clear System does not record messagesNew voicemail and show on the screens, and I don’t know why Cannot retrieve voicemail messages Common cure for electronic equipment Cleaning your telephone MaintenanceTaking care of your telephone Avoid water Safety information Important safety information Especially about cordless telephones Industry Canada FCC Part 68 and Acta FCC Part Call 1 800 222-3111. In Canada, dial 1 866 Limited warranty How do you get warranty service? Operation Operating time Technical specifications Index 112 Action Remote command Remote access wallet card