Manuals / ATTO Technology / Computer Equipment / Network Router

ATTO Technology 2400C/R/D, 2370E, 2390C/R/D operation manual zModem Send filename Receive

Models: 2400C/R/D 2390C/R/D 2370E

1 51

Page 47

zModem

Allows transfer of a firmware image to or from the FibreBridge using the zModem file transfer protocol. Available only through the RS232 interface.

zModem [Send filename Receive]

CAUTION

After a firmware image is downloaded to the FibreBridge, the image is placed into flash memory. During this time (about 30 seconds), DO NOT remove power to the FibreBridge or the flash may become corrupted.

xvi

Page 47

Image 47

ATTO Technology 2400C/R/D, 2370E, 2390C/R/D operation manual zModem Send filename Receive

Contents

ATTO FibreBridge 2400C/R/D ATTO FibreBridge Installation and Operation ManualATTO FibreBridge 2370E ATTO FibreBridge 2390C/R/D sls@attotech.com ATTO Technology, Inc155 CrossPoint Parkway Amherst, New York 14068 USA Sales support1.2 ATTO FibreBridge 2390R/D Contents1.0 ATTO FibreBridge provides storage options 1.1 ATTO FibreBridge 2370E3.2 Remote monitoring, management 2.0 Installing the FibreBridge3.0 Configuring the FibreBridge 3.1 Map devicesManufacturer limited warranty Appendix D Warranty information1.0 ATTO FibreBridge provides storage options ATTO FibreBridge 2370E features, benefitsATTO FibreBridge 2400C/R/D features, benefits ATTO FibreBridge 2390C/R/D features, benefitsLED indicators Board dimensionsPower Management accessExhibit 1.1-1 FibreBridge 2370E board layout LED Header P5 PinsLED Header P6 Pins Management ports Dimensions1.2 ATTO FibreBridge 2390R/D Fibre Channel interfaceLED indicators Manual reset switchA manual reset switch reboots the FibreBridge Manual reset switch 1.3 ATTO FibreBridge 2390CBoard dimensions Management accessExhibit 1.3-2 The FibreBridge 2390C board layout Exhibit 1.3-1 The FibreBridge 2390C connectors and LEDSCooling and airflow 1.4 ATTO FibreBridge 2400R/DDimensions PowerPower receptacle Manual reset switchLED indicators air vents Ready/Fault LEDSCSI activity LEDsManagement access 1.5 ATTO FibreBridge 2400CBoard dimensions Powermounting hole 10-pin serial header Ready/Fault LED Ethernet portcPCI connector 6.299 inchesDiscover the IP address 2.0 Install the FibreBridgeUnpack the packing box verify contents Install the FibreBridge5 Click on Launch Browser Internet Explorer setupBegin initial configuration Interface options on pageModify passwords 3.0 Configure the FibreBridgeUsing ExpressNAV on Port configurationsEnhance performance SCSI device mapping 3.1 Map devicesFibreBridge mapping Mapping devices manually Multiple Node addressing FB2400 onlyMapping devices automatically ExpressNAV on page3.2 Remote monitoring, management Consult your network administrator for further assistance with SNMP SNMP-based monitoringEmail messages provide error notification IP Addresses Subject The Type of Event that Occurred Message BodyUnit Information Serial Number Serial NumberUsing the zModem command 4.0 Update firmwareUsing ExpressNAV Using FTP7 Click Send File Opening an ExpressNAV session Using ExpressNAVUsing the serial port 5.0 Interface optionsEnter Using TelnetSerial port connections Appendix A CablingSCSI port connections Fibre Channel connectionsIndicates Appendix B CLI provides ASCII-based interfaceCommand conventions SymbolDefault CLI error messagesCLI summary reference CommandExample CommandDefault Example CommandDefault Command explanations DisplayTraceLog DumpConfigurationDisplayEventLog DisplayEventLogFilterEmailNotifyAddress FCMultiNode FB2400 only FCPortErrorsFCHard FCHardAddressFirmwareRestart RestoreConfiguration PasswordReadOnlyPassword Reset FCPortErrorsRoute xiii Controls whether or not SNMP functions on the FibreBridgeSNMPTraps SpeedWriteDefaultDefault 192.43.244.18 time.nist.gov set SNTPServer SNMPTrapAddressTimeZone zModem Send filename Receive zModemEuropean Standards Appendix C Standards and compliancesFCC Standards Radio and Television Interference Canadian StandardsCertification for the FibreBridge 2400 only Appendix D Warranty information