Manuals / ATTO Technology / Computer Equipment / Network Router

ATTO Technology 2400C/R/D Manual reset switch, A manual reset switch reboots the FibreBridge

Models: 2400C/R/D 2390C/R/D 2370E

1 51

Download 51 pages 36.41 Kb

Page 11

Manual reset switch

Manual reset switch

A manual reset switch reboots the FibreBridge.

To reset the FibreBridge, depress the reset button for no more than three seconds.

To restore factory defaults, press the reset button for more than four seconds until the green Ready LED blinks.

LED indicators

The LED indicators can be viewed from the connector (back) side and the front side of the FibreBridge 2390R/D. (See Exhibit 1.2-1)

LEDs on the connector (back) side are:

A bicolor Ready/Fault LED lights green to indicate ready, lights yellow to show a faulted condition, and is off to indicate not ready.

Embedded in the Ethernet port connector: a lighted green LED shows a valid link; off indicates

that no link is present. A separate blinking yellow LED indicates activity.

Fibre Channel port: A lighted green LED indicates link; off means no link. A separate green LED indicates activity if it is lit, no activity if it is off. SCSI ports: A green LED on each port indicates activity if is lit.

LEDs on the front panel are:

A bicolor Ready/Fault LED is lighted green to indicate ready, lighted yellow to show a faulted condition, and off indicates not ready.

SCSI ports: A green LED on each port indicates activity if is lit.

Fibre Channel port: bicolor LED indicates FC speed. If it is off, speed is 1-Gb; if it is green, 2-Gb, and yellow indicates 4-Gb FC. A separate green LED indicates activity if it is lit, no activity if it is off.

Exhibit 1.2-1 Fibre Bridge 2390R/D dimensions with front panel LEDs and connector side details

Ready, Fault LEDs

FC Activity, Link LEDs

SCSI Activity LEDs

Serial port Ethernet port Fibre Channel port SCSI ports	Power receptacle
Reset switch

6

Image 11

ATTO Technology 2400C/R/D, 2370E Manual reset switch, A manual reset switch reboots the FibreBridge, LED indicators

Contents

ATTO FibreBridge 2400C/R/D ATTO FibreBridge Installation and Operation ManualATTO FibreBridge 2370E ATTO FibreBridge 2390C/R/D sls@attotech.com ATTO Technology, Inc155 CrossPoint Parkway Amherst, New York 14068 USA Sales support1.2 ATTO FibreBridge 2390R/D Contents1.0 ATTO FibreBridge provides storage options 1.1 ATTO FibreBridge 2370E3.2 Remote monitoring, management 2.0 Installing the FibreBridge3.0 Configuring the FibreBridge 3.1 Map devicesManufacturer limited warranty Appendix D Warranty information1.0 ATTO FibreBridge provides storage options ATTO FibreBridge 2370E features, benefitsATTO FibreBridge 2400C/R/D features, benefits ATTO FibreBridge 2390C/R/D features, benefitsLED indicators Board dimensionsPower Management accessExhibit 1.1-1 FibreBridge 2370E board layout LED Header P5 PinsLED Header P6 Pins Management ports Dimensions1.2 ATTO FibreBridge 2390R/D Fibre Channel interfaceLED indicators Manual reset switchA manual reset switch reboots the FibreBridge Manual reset switch 1.3 ATTO FibreBridge 2390CBoard dimensions Management accessExhibit 1.3-2 The FibreBridge 2390C board layout Exhibit 1.3-1 The FibreBridge 2390C connectors and LEDSCooling and airflow 1.4 ATTO FibreBridge 2400R/DDimensions PowerPower receptacle Manual reset switchLED indicators air vents Ready/Fault LEDSCSI activity LEDsManagement access 1.5 ATTO FibreBridge 2400CBoard dimensions Powermounting hole 10-pin serial header Ready/Fault LED Ethernet portcPCI connector 6.299 inchesDiscover the IP address 2.0 Install the FibreBridgeUnpack the packing box verify contents Install the FibreBridge5 Click on Launch Browser Internet Explorer setupBegin initial configuration Interface options on pageModify passwords 3.0 Configure the FibreBridgeUsing ExpressNAV on Port configurationsEnhance performance SCSI device mapping 3.1 Map devicesFibreBridge mapping Mapping devices manually Multiple Node addressing FB2400 onlyMapping devices automatically ExpressNAV on page3.2 Remote monitoring, management Consult your network administrator for further assistance with SNMP SNMP-based monitoringEmail messages provide error notification IP Addresses Subject The Type of Event that Occurred Message BodyUnit Information Serial Number Serial NumberUsing the zModem command 4.0 Update firmwareUsing ExpressNAV Using FTP7 Click Send File Opening an ExpressNAV session Using ExpressNAVUsing the serial port 5.0 Interface optionsEnter Using TelnetSerial port connections Appendix A CablingSCSI port connections Fibre Channel connectionsIndicates Appendix B CLI provides ASCII-based interfaceCommand conventions SymbolDefault CLI error messagesCLI summary reference CommandExample CommandDefault Example CommandDefault Command explanations DisplayTraceLog DumpConfigurationDisplayEventLog DisplayEventLogFilterEmailNotifyAddress FCMultiNode FB2400 only FCPortErrorsFCHard FCHardAddressFirmwareRestart RestoreConfiguration PasswordReadOnlyPassword Reset FCPortErrorsRoute xiii Controls whether or not SNMP functions on the FibreBridgeSNMPTraps SpeedWriteDefaultDefault 192.43.244.18 time.nist.gov set SNTPServer SNMPTrapAddressTimeZone zModem Send filename Receive zModemEuropean Standards Appendix C Standards and compliancesFCC Standards Radio and Television Interference Canadian StandardsCertification for the FibreBridge 2400 only Appendix D Warranty information