English

Troubleshooting

Turntable does not operate

1.Make certain the turntable’s AC cord is plugged into an AC outlet, and that the AC outlet is “live.”

2.Check the drive belt to make certain it is on correctly. (See Figure 11.)

A)Remove the record mat from the turntable platter (Fig. 11a). Place the mat in the cardboard packaging sleeve for safekeeping. Through an opening in the turntable platter, visually inspect to see if the drive belt is around the motor pulley (Fig. 11b).

B)If the drive belt is not around the motor pulley: Lift and remove the turntable. Place a thumb into each of the left and right openings on the turntable platter; and, using the fingers to press down on the turntable housing’s surface, pull the platter straight up (Fig. 11c). Avoid pressing on the tone arm.

C)With the turntable platter bottom side up, place the belt along the outside wall of the turntable platter’s drive rim, making certain that the belt is smooth and flat all the way around (Fig. 11d).

D)Put the turntable back on the center spindle, make certain it is fully seated, and align one of its openings over the motor pulley position.

E)Through the opening, carefully hook the turntable belt with a finger or with the original red ribbon (never use a sharp object) and pull the belt over the motor pulley (Fig. 11e). Make certain the belt is not twisted between the pulley and the platter’s drive rim.

F)Put the record mat back on the platter.

G)While holding the tone arm in its rest position, slowly turn the platter by hand clockwise at least 10 rotations to clear the mechanism’s automatic cycle.

Turntable operates, but no sound at all

1.The stylus guard is still in place.

2.The tone arm Lift button is pressed in.

3.Amplifier controls set incorrectly: wrong input selected, tape monitor on, speakers switched off, etc.

4.Check the stylus on phono cartridge for correct placement. Refer to the instructions for replacing the stylus on page 6.

Turntable operates, but no sound, or sound not loud enough

1.If the turntable is connected to an AUX (high-level) input: The Pre-amp Selector Switch may be set to the “PHONO” position (phono-input level).

2.The input gain of the amplified speaker or similar device may be too low.

3.The stylus assembly may not be fully seated in the cartridge body. (See Fig. 10 on page 6.)

Sound is very distorted

1.Turntable connected to an amplifier’s PHONO input: If the pre-amp switch is set to the “LINE” position (AUX high-level output), a phono input will be overloaded.

Record/tone arm moves slightly up and down

1.Usually this is a normal condition and not a problem. If this causes the turntable to be unable to track the record, please contact your dealer or our service department. Make very certain the surface upon which the turntable is resting is not picking up vibrations from the floor or walls, or from direct speaker sound.

Figure 11 – Checking the drive belt

11a

11b

11c

11d

Drive belt

11e

Motor pulley

7

Page 7
Image 7
Audio-Technica AT-LP60-USB manual Troubleshooting

AT-LP60-USB specifications

The Audio-Technica AT-LP60-USB is a remarkable entry-level turntable that bridges the gap between classic vinyl enjoyment and modern digital convenience. Designed for both novice listeners and audiophiles alike, this fully automatic belt-drive turntable stands out for its combination of affordability, performance, and user-friendliness.

One of the key features of the AT-LP60-USB is its fully automatic operation. With just the push of a button, users can start the turntable with ease. The tonearm lifts and lowers automatically, ensuring minimal contact with the record. This feature not only enhances convenience but also helps to preserve vinyl records over time, as the stylus minimizes the risk of scratching.

Equipped with a high-quality dual-magnet cartridge, the AT-LP60-USB delivers exceptional audio fidelity, ensuring that listeners can enjoy the warm, rich sound inherent to vinyl. The included ATN3600L stylus provides clarity and precision, capturing the full spectrum of sound from any record. This model is compatible with both 33 1/3 RPM and 45 RPM records, allowing users an extensive range of vinyl options.

Another standout feature of this turntable is its USB output, which provides the ability to convert vinyl records into digital formats. This aspect is especially appealing for those who wish to preserve their collections in a more modern, portable format. By connecting the AT-LP60-USB to a computer, users can easily digitize their favorite albums, making them accessible for playback on various digital devices.

In terms of build quality, the turntable boasts a sleek, minimalist design that fits well in any home setting. Its lightweight plastic chassis and detachable dust cover contribute to its user-friendly design. Additionally, the unit comes with a built-in dual RCA output, making it easy to connect to a variety of audio systems.

The AT-LP60-USB also incorporates an anti-resonance design, which aids in minimizing vibrations and enhancing sound quality. This thoughtful engineering allows the turntable to deliver a clean and uninterrupted audio experience, crucial for enjoying the authenticity of vinyl playback.

In conclusion, the Audio-Technica AT-LP60-USB is an exceptional choice for anyone looking to experience the magic of vinyl in an intuitive and high-quality package. With its automatic operation, USB capability, and impressive sound fidelity, it's an excellent gateway for both new listeners and seasoned vinyl enthusiasts.