Manuals / Brocade Communications Systems / Computer Equipment / Network Card

Brocade Communications Systems 53-1002163-02 manual Configuring the FCoE login information

Models: 53-1002163-02

1 168

Download 168 pages 40.76 Kb

Page 48

4	Configuring the FCoE login information
		Clearing logins
		Perform the following task to clear logins.

		Task	Command

		Clear the logins that occurred through a front-end	switch:admin> fcoe --resetlogin -teport slot/port
		port or from a device specified by the ENode's	-device wwn
		VN_port WWN. Syntax is as follows:
		• -teportslot/port—Specifies the slot or port

number.

• -devicewwn—Specifies the device WWN.

Displaying FCoE configuration-related information

Perform the following tasks to display FCoE-related configuration information.

Task	Command

Display the embedded FCoE port configuration.	switch:admin> fcoe --cfgshow[slot/port]
Configurations of all the ports are displayed if you
do not specify a specific port.

Display information about devices logged in to a	switch:admin> fcoe --loginshow [slot/port]
specific FCoE F_port.

Display FIP configurations.	switch:admin> fcoe --fipcfgshow

Configuring the FCoE login information

Another important task in administrating FCoE is configuring the FCoE login information.

Enabling or disabling login configuration management

The fcoelogincfg command allows only configured ENode VN_ports to log in. Use the fcoelogingroup command to configure allowed ENode VN_ports. The default is disabled.

Disabling the fcoelogincfg command allows unrestricted login on ENode VN_ports.

Perform one of the following tasks to toggle the availability of FCoE login configuration management.

Task	Command

Enable the FCoE login configuration management	switch:admin> fcoelogincfg --enable
on the switch (this is a switch-based command,
not port-based).

Disable the FCoE login configuration	switch:admin> fcoelogincfg --disable
management on the switch.

26	Converged Enhanced Ethernet Administrator’s Guide
	53-1002163-02

Image 48

Brocade Communications Systems 53-1002163-02 manual Configuring the FCoE login information, Clearing logins

Contents

Converged Enhanced Ethernet Brocade Communications Systems, Incorporated Title Publication number Summary of changes DateTitle Publication number Summary of changes Date Converged Enhanced Ethernet Administrator’s Guide Contents Chapter Using the CEE CLI This chapterChapter Initial FCoE and CEE Configuration Chapter Configuring STP, RSTP, and Mstp Chapter Configuring Link Aggregation 101 107123 127131 Appendix a Strict priority and Weighted Round Robin scheduler Strict priority schedule two queuesWRR schedule two queues Page Tables Page Configuring VLANs, describes how to configure VLANs About This DocumentThis chapter How this document is organizedSupported hardware and software What’s new in this documentCommand syntax conventions Document conventionsText formatting Additional information Key termsCorporation Referenced Trademarks and Products Getting technical help Brocade resourcesOther industry resources Document feedback FT00X0054E9Introducing FCoE FCoE terminologyFCoE overview Term DescriptionFCoE hardware Layer 2 Ethernet overview Layer 2 forwardingLayer 2 Ethernet overview Vlan tagging Loop-free network environmentFrame classification incoming Congestion control and queuingConverged Enhanced Ethernet Administrator’s Guide Access control TrunkingFCoE Initialization Protocol Flow ControlFIP discovery FIP login FIP logoutFCoE login LogincfgFCoE logout FCoE Initialization ProtocolName server FC zoningRegistered State Change Notification Rscn Upgrade and downgrade considerations for FCoE FCoE queuingUsing the CEE CLI CEE Command Line InterfaceManagement Tools Saving your configuration changes Accessing the CEE CLI through the console or TelnetSaving configuration changes with the copy command Saving configuration changes with the write memory commandAccessing the CEE CLI from the Fabric OS shell CEE CLI command modesTo return to the Fabric OS CLI, enter the following command Interface port-channel CEE Command Line Interface CEE CLI command modes CEE CLI keyboard shortcutsLists CEE CLI keyboard shortcuts Keystroke DescriptionUsing the do command as a shortcut Displaying CEE CLI commands and command syntaxCEE CLI command completion CEE CLI command output modifiersCEE Command Line Interface CEE CLI command output modifiers TeeConfiguration management Configuration management tasksCEE configuration guidelines and restrictions Display the running configuration file Saving the running configuration fileLoading the startup configuration file Erasing the startup configuration fileFlash file management commands Debugging and logging commandsArchiving the startup configuration file Restore an archived startup configuration fileSwitch#show debug FCoE Configuration Management Managing the FCoE configurationFCoE configuration guidelines and restrictions This chapterConfiguring the FCoE login information Clearing loginsDisplaying FCoE configuration-related information Enabling or disabling login configuration managementManaging the current configuration transaction Cleaning up login groups and VNport mappingsDisplaying the FCoE login configuration Creating an FCoE login group Saving the current FCoE configurationCreating an FCoE login group Modifying the FCoE login group device list Deleting an FCoE login groupRenaming an FCoE login group Perform the following task to delete an FCoE login groupCreating an FCoE login group Initial FCoE and CEE Configuration End to End FCoE using FC ISLsOverview FCoE Logical Port Numbering FCoE port-to-front end TenGigabit port mappingHigh availability Hot plugControl Processor failover Protocol type Time intervalHigh availability reference Operation, data, or state Expected behaviorConfiguring the FCoE interfaces Configuring the FCoE VlanAssigning an FCoE map onto an interface Show vlan fcoeConfiguring Dcbx Return to the privileged Exec mode using the end commandRepeat this procedure for any additional interfaces Activate the protocolConfiguring Spanning Tree Protocol Configuring Vlan membershipConfiguring Spanning Tree Protocol CEE map configuration Bandwidth%Activate the CEE map mode Defining a Priority Group Table mapDefine the CEE map for Pgid CoSPGIDDefining a Priority-Table map Applying a CEE provisioning map to an interfaceVerifying the CEE maps Activate privileged Exec mode CEE audit logsName Example Description Page CEE audit logs Configuring VLANs Vlan overviewIngress Vlan filtering Displays the frame processing logic for an incoming frame Vlan configuration guidelines and restrictions Default Vlan configurationParameter Default setting Vlan configuration and management Configuring the MTU on an interface portEnabling and disabling an interface port Creating a Vlan interfaceConfiguring a Vlan interface to forward FCoE traffic Enabling STP on a VlanDisabling STP on a Vlan Configuring an interface port as a Layer 2 switch port Configuring an interface port as an access interfaceConfiguring an interface port as a trunk interface Configuring an interface port as a converged interface Disabling a Vlan on a trunk interfaceConfiguring protocol-based Vlan classifier rules Configuring protocol-based Vlan classifier rulesDisabling a Vlan on a converged interface Configuring a Vlan classifier rule Configuring MAC address-based Vlan classifier rulesDeleting a Vlan classifier rule Creating a Vlan classifier group and adding rulesConfiguring the MAC address table Activating a Vlan classifier group with an interface portClearing Vlan counter statistics Displaying Vlan informationSpecifying or disabling the aging time for MAC addresses Adding static addresses to the MAC address tableConfiguring the MAC address table Configuring STP, RSTP, and Mstp STP overviewConfiguring STP Rstp overview STP interface state Rstp interface stateActive topology? Is the interface learning MAC addresses?Configuring Rstp Mstp overview Mstp overviewConfiguring Mstp Default STP, RSTP, and Mstp configuration STP, RSTP, and Mstp configuration and management Enabling STP, RSTP, or MstpSTP, RSTP, and Mstp configuration and management Disabling STP, RSTP, or MstpShutting down STP, RSTP, or Mstp globally Specifying the bridge prioritySpecifying the bridge forward delay Specify the bridge forward delaySpecifying the bridge maximum aging time Enabling the error disable timeout timer Specifying the error disable timeout intervalEnable the error disable timeout timer Specifying the port-channel path costSpecifying the bridge hello time STP and Rstp Specifying the transmit hold count Rstp and MstpSpecify the port-channel path cost Enabling Cisco interoperability Mstp Disabling Cisco interoperability MstpMapping a Vlan to an Mstp instance Specifying a revision number for an Mstp configuration Enter the region command to assign a name to an Mstp regionSpecifying the maximum number of hops for a Bpdu Mstp Specifying a name for an Mstp regionFlushing MAC addresses Rstp and Mstp Clearing spanning tree countersClearing spanning tree-detected protocols Configuring STP, RSTP, or Mstp on CEE interface ports Configuring the path costDisplaying STP, RSTP, and MSTP-related information Enabling automatic edge detectionEnabling a port interface as an edge port Enabling the guard rootEnter the no shutdown command to enable the CEE interface Specifying the Mstp hello timeSpecifying restrictions for an Mstp instance Specifying a link type Enabling port fast STPSpecifying the port priority Restricting the port from becoming a root port Restricting the topology change notificationEnabling spanning tree Disabling spanning tree Configuring STP, RSTP, or Mstp on CEE interface ports Configuring Link Aggregation Link Aggregation Group configurationLink aggregation overview Converged Enhanced Ethernet Administrator’s Guide Data Center Core Link Aggregation Control Protocol Dynamic link aggregationStatic link aggregation Brocade-proprietary aggregationLacp configuration guidelines and restrictions Default Lacp configurationLacp configuration and management LAG distribution processEnabling Lacp on an interface in Layer 2 mode Configuring the Lacp system priorityConfiguring the Lacp timeout period on a CEE interface Enter the switchport mode command to set the modeLacp troubleshooting tips Clearing Lacp counter statistics on a LAGClearing Lacp counter statistics on all LAG groups Displaying Lacp informationDeskew calculation failed for link link-name Configuring Lldp Lldp overviewLayer 2 topology mapping Layer 2 topology mappingDcbx overview Enhanced Transmission Selection ETS Priority Flow Control PFCPriority Priority group Bandwidth check Lldp configuration guidelines and restrictions Default Lldp configurationDcbx interaction with other vendor devices Lldp configuration and management Disabling and resetting Lldp globallyConfiguring Lldp global command options Enabling Lldp globallySpecifying a system name for the Brocade FCoE hardware Specifying a user description for LldpConfiguring the transmit frequency of Lldp frames Configuring the hold time for receiving devicesAdvertising the optional Lldp TLVs Configuring the advertisement of Lldp DCBX-related TLVs Configuring FCoE priority bitsAdvertise the Lldp DCBX-related TLVs using these commands Configure the FCoE priority bitsConfiguring iSCSI priority bits Configuring Lldp profilesConfiguring the iSCSI profile Configuring Lldp interface-level command options Clearing LLDP-related informationDisplaying LLDP-related information Display Lldp neighbor-related detail information Display Lldp interface-related informationDisplay all Lldp statistics Lldp configuration and management Configuring ACLs ACL overviewDefault ACL configuration ACL configuration guidelines and restrictionsACL configuration and management Creating a standard MAC ACL and adding rulesCreating an extended MAC ACL and adding rules Modifying MAC ACL rulesEnter the no seq command to delete the existing rule Removing a MAC ACLReordering the sequence numbers in a MAC ACL ACL configuration and management Applying a MAC ACL to a CEE interfaceApplying a MAC ACL to a Vlan interface ACL configuration and management Configuring QoS QoS overviewDefault user-priority mappings for untrusted interfaces RewritingQueueing User-priority mappingConfiguring the QoS trust mode Incoming CoS User PriorityConfiguring user-priority mappings Creating a CoS-to-CoS mutation QoS mapApplying a CoS-to-CoS mutation QoS map Traffic class mapping Unicast trafficUser priority Traffic class Multicast traffic Mapping CoS-to-Traffic-ClassActivating a mapping CoS-to-Traffic-Class QueueingCongestion control Tail dropVerifying a mapping CoS-to-Traffic-Class Ethernet pause Changing the Tail Drop thresholdEthernet Priority Flow Control Enabling Ethernet PauseEnable trust mode on the interface Enable an Ethernet PFC on the interfaceMulticast rate limiting Enabling an Ethernet PFCDeficit weighted round robin scheduling SchedulingStrict priority scheduling Traffic class scheduling policy Scheduling the QoS queueMulticast queue scheduling Scheduling the QoS multicast queueMulticast traffic class Equivalent unicast traffic class Pgid Defining a priority group table Defining a priority-table mapSpecify the name of the CEE map to define Applying a CEE provisioning map to an interface Verifying the CEE mapsConfiguring 802.1x Port Authentication 802.1x configuration guidelines and restrictions802.1x protocol overview 802.1x authentication configuration tasks Interface-specific administrative tasks forConfigure authentication Between the switch and CNA or NIC Configuring 802.1x on specific interface portsConfiguring 802.1x timeouts on specific interface ports Configure the timeout intervalEnable 802.1x authentication for the interface port Configure reauthentication for the interface portInterface-specific administrative tasks for Configuring Igmp About IgmpActive Igmp snooping Configuring Igmp Multicast routingConfiguring Igmp snooping querier Configuring Igmp snooping mrouterConfigure the mrouter timeout value Monitoring IgmpConfiguring Rmon Rmon configuration and managementDefault Rmon configuration Configuring Rmon group statistics collectionConfiguring Rmon settings Configuring Rmon eventsEnable the CEE interface Configure Rmon group statistics on the interfaceConfiguring Rmon history collection Rmon configuration and management Configure the Rmon eventActivate Rmon history collection for the interface Display the Rmon historyRmon configuration and management Brocade 8000 Replacement SwitchBrocade 8000 Replacement Enhanced Group Management licenseOriginalswitchadmin cfgactvshow Bring the new switch back online Upload the startup-configfile to the new switchUpload the running-configfile to the new switch Originalswitchadmin switchname originalswitch Brocade 8000 Replacement Index 802.1xQoS, 113 queuing FIP Layer LldpRadius Vlan