Manuals / Brother / Computer Equipment / Printer

Brother MFC/HL-P2000 manual Operating And Storage Environment, Power Supply

Models: MFC/HL-P2000

1 89

Download 89 pages 57.43 Kb

Page 13

USER’S GUIDE

OPERATING AND STORAGE ENVIRONMENT

Please take note of the following before using the machine.

Power Supply

Use the machine within the specified power range.

AC power: ±10% of the rated power voltage in your country

Frequency: 50/60 Hz (220 V– 240 V) or 50/60 Hz (110–120 V)

The power cord, including extensions, should not exceed 5 meters (16.5 feet).

Do not share the same power circuit with other high-power appliances, particularly an air conditioner, copier, shredder and so on. If it is unavoidable that you must use the machine with these appliances, it is recommended that you use an isolation transformer or a high-frequency noise filter.

Use a voltage regulator if the power source is not stable.

Environment

The machine should be installed near a power outlet which is easily accessible.

Use the machine only within the following ranges of temperature and humidity.

Ambient temperature: 10°C to 32.5°C (50°F to 90.5°F)

Ambient humidity:

20% to 80% (without condensation)

The machine should be used in a well ventilation room.

Place the machine on a flat, horizontal surface.

Keep the machine clean. Do not place the machine in a dusty place.

Do not place the machine where the ventilation hole of the machine can be blocked.

Do not place the machine where it is exposed to direct sunlight. Use a blind or a heavy curtain to protect the machine from direct sunlight when the machine is unavoidably set up near a window.

Do not place the machine near devices that contain magnets or generate magnetic fields.

1-6

Image 13

Brother MFC/HL-P2000 manual Operating And Storage Environment, Power Supply

Contents

User’s Guide Brother Laser Printer / Scanner / CopierPlease read this manual thoroughly before using the machine MFC/HL-P2000CHAPTER 1 INTRODUCTION TABLE OF CONTENTSCHAPTER 2 PAPER HANDLING CHAPTER 3 PRINTCHAPTER 4 COPY CHAPTER 6 MAINTENANCECHAPTER 5 SCAN SCANNING FROM THE VISIONEER PaperPortLE SOFTWAREAPPENDIX CHAPTER 7 TROUBLESHOOTINGINDEX To Use the Machine Safely Definitions of Warnings, Cautions, and NotesHigh Temperature Shipment of the Machine VOID THE WARRANTYFor USA & CANADA Only CHAPTER INTRODUCTION Finding Out How to Use the MachineABOUT THE GUIDEBOOKS Machine Overview ABOUT YOUR MACHINEUSER’S GUIDE Fig. 1-1 Front ViewFeatures System Requirements in Brother Printing Solution for WindowsHigh Resolution and Fast Printing Speed Versatile Paper HandlingEnhanced Printing Performance and User-Friendly Operation for Windows TWAIN Compliant Scanner DriverRemote Printer Console Program for DOS Popular Printer Emulation SupportSleep Mode Power Save Mode Environment-Friendly Economy Printing ModeEnhanced Memory Management Low Running CostOPERATING AND STORAGE ENVIRONMENT Power SupplyEnvironment Do not subject the machine to strong physical shocks or vibrations Keep the machine horizontal when carrying itDo not expose the machine to open flames or salty or corrosive gasses Do not place objects on top of the machineCHAPTER2 PAPER HANDLING PAPER SPECIFICATIONSPaper Type Paper SizeCut Sheet RemarksLabels / Transparencies Fig. 2-1 Fan the Paper and Straighten the Paper Special PaperEnvelopes Paper Capacity in Document Feeder DOCUMENT SPECIFICATIONSEnvelopes, Organizer 10 sheets MULTI-PURPOSE SHEET FEEDER FOR PRINTING Loading Paper into the Feeder 3. Move the paper guide to the paper width. ➀ Two Side Printing Manual Duplexing OUTPUT TRAY AND PAPER SUPPORT WIRE CHAPTER PRINT LAMPS AND SWITCHReady Paper Lamp Data Toner Lamp Alarm LampDrum Lamp Other Control Features SwitchCancel printing Error RecoveryAlarm Test Print ModeLamp Lit ChoiceTO MAKE SETTINGS FOR EACH COPY COPYING IN STANDARD MODECHAPTER COPY Enlarge/Reduce Photo/TextCHAPTER 4 COPY The Number of CopiesFig. 4-2 Enlarge and Reduce Error SCANNING FROM TWAIN COMPLIANT APPLICATIONS CHAPTER SCAN3. Make the necessary settings 4. Press the Start button SCANNING FROM THE VISIONEER PaperPort LE SOFTWARE MFC-P20001. Launch the Visioneer PaperPortLE application 2. Click the Scan icon The scanner driver dialog is launched1. Launch the Unimessage Viewer application 2. Select “Scan” REPLACING THE TONER CARTRIDGE CHAPTER MAINTENANCEpossible toner spill or scatter Keep the drum unit level after removing the toner cartridge, to avoidCHAPTER 6 MAINTENANCE High TemperatureFig. 6-3 Inside the Machine Fig. 6-4 Turning the Lever to Close the Shuttertime, the toner life is shortened 7. Turn the drum unit upside down gently Fig. 6-9 Cleaning the Primary Corona Wire 9. Re-install the drum unit into the machine and close the top coverUSER’S GUIDE Fig. 6-10 Close the top coverFig. 6-11 Drum Unit Nearly at the End of its Life REPLACING THE DRUM UNITFollow these steps to replace the drum unit High TemperatureDo not remove the starter sheet Fig. 6-17 Installing the Drum Unit 5. Install the new drum unit into the machine6. Close the top cover USER’S GUIDECleaning the Machine Exterior CLEANING THE MACHINEHigh Temperature Cleaning the Machine Interior and Drum UnitFig. 6-20 Turning off the Switch and Unplugging Fig. 6-21 Inside the MachineScanner Window Fig. 6-22 Cleaning the Scanner WindowSee the section “REPLACING THE DRUM UNIT” in this chapter Fig. 6-24 Cleaning the Scanning Unit Cleaning the Scanning UnitRE-PACKING THE MACHINE 5. Close the top cover, the extension wire, and the output tray ALARM INDICATIONS AT A GLANCE CHAPTER TROUBLESHOOTINGOperator Calls for the Printing Function Alarm ↔Page Operator Calls for the Copying and Scanning Functions Alarm Service Calls for the Printing FunctionAlarm AlarmService Calls for the Copying and Scanning Functions High Temperature PAPER JAMSFig. 7-1 Locating Paper Jam Position Fig. 7-2 Inside the MachinePaper Jam in the Multi-Purpose Sheet Feeder Paper Jam near the Drum Unit or at the Paper Output Tray Paper Jam in the Document Feeder CHAPTER 7 TROUBLESHOOTINGFig. 7-7 Paper Jam in the Document Feeder Setting Up the Machine for Windows Setting Up the Machine HardwareQ & A power switch is onQuestion Setting Up the Machine for DOSRecommendation Question Paper HandlingRecommendation loading paper, see “Paper Handling” in ChapterQuestion PrintingRecommendation Scan CopyQuestion RecommendationQuestion Print QualityRecommendation Interior and Drum Unit” in ChapterRecommendation QuestionFig. 7-11 Scattering Toner Fig. 7-12 Black PageRecommendation QuestionMachine Interior and Drum Unit.” Recommendation QuestionFig. 7-17 Black Spots position of smudge o on the drum 94mm interval600 dots/inch Scanning CopyingElectrical and Mechanical FunctionsPARALLEL INTERFACE SPECIFICATIONS Fig. A-1 Parallel Interface Cable APPENDIXBitmapped Fonts RESIDENT FONTSHP LaserJet IIP Mode SYMBOL SETS/CHARACTER SETSEPSON Mode IBM ModeUSER’S GUIDE HP LaserJet IIPAPPENDIX HP LaserJet IIP, EPSON FX-850, IBM Propritner XL EPSON FX-850A-10 USER’S GUIDECompilation and Publication Notice TrademarksThis product is designed for use in a professional environment REGULATIONSFederal Communications Commission Compliance Notice For USA Only Industry Canada Compliance Statement For Canada OnlyInternational Energy Star Compliance Statement Laser Safety For 110-120 V Model OnlyRadio Interference 220-240 V Model Only FDA Regulations For 110-120 V Model Only IEC 825 Specification For 220-240 V Model OnlyDeclaration of Conformity For Europe CAUTION ADVARSEL VARNING VARO ADVARSEL ATTENTION VORSICHT ATENCIÓNGeräuschemission / Acoustic Noise Emission For Germany Only IMPORTANT - For Your SafetyFor Finland and Sweden LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT Disconnect deviceIMPORTANT - Wiring Information For U.K. only INDEX