Manuals / BT / Communications / Telephone

BT BT Versatility manual Power up and test, Commissioning, Switch on

Models: BT Versatility

1 59

Download 59 pages 3.62 Kb

Page 47

Image 47

BT Versatility

Installation and maintenance Manual

Power up and test

•Ensure the mains plug is fitted with a 3A fuse.

Switch on

•Power up the system by inserting the mains plug.

•Wait approximately 30 seconds for the system power up routine to be complete.

•Check that the vital activity LED is flashing. This is the top led of the four LEDs in the CCU MDF area.

•Check the Power led is lighting. This is the third led in the CCU MDF area

Commissioning

1.Remove any anti-scratch protective film from Featurephone LCD’s.

2.Label up all Featurephones and other telephones.

3.Ensure that all Featurephones provide dialling tone, ringing and hands free (loud speaking) facilities. Check that the display is not showing corrupt information.

4.Carry out a 'First Day Reset'.

5.Check that all other telephones are connected. Make sure all these phones ring and that you can dial from them.

6.Commission System

Page 47

Image 47

BT BT Versatility manual Power up and test, Commissioning, Switch on

Contents

Communications without the complications Installation and Maintenance ManualBT Versatility BT Versatility ContentsGeneral overview IntroductionLightning and surge voltage protection Safety Precautions during installation and system upgradesElectrostatic precaution ESP Versatility Value Add Packs BT Versatility Pro. PlusIncludes System, VM, 1M,2V8BT Versatility Voice Digital Includes System BT Versatility Voice Analogue Inculdes SystemBT Versatility Maintenance itemsTHIRD, install the Network and Expansion modules as required Installation checklistMounting the CCU Installing the Central Control UnitCCU LocationCCU 300mm CCU Mounting bracket clearances300mm min Mounting the CCUModule location Modules located in the CCUMounting the CCU with two brackets Installing the Backplane wall bracketSystem Expansion Securing the backplane to the wall bracket Mounting the BackplaneExpansion Modules Push up to lock Installing an Expansion moduleBT Versatility Analogue line module Installing the Analogue Module in the CCUFirst network module To Locate the Analogue Module in the Ports ModuleBT Versatility Digital Line Module ISDN First network module Installing the Basic Rate ISDN Module in the CCUBasic Rate ISDN expansion module BT VersatilityFirst network module To Locate the Digital Line Module ISDN 2 in the PORTS moduleS0 interface termination System ISDN settingsT0 interface termination BT Versatility Voicemail moduleBack up Voice Module voice messages and Greetings BT Versatility Primary Rate Interface Availability TBCConnecting the battery backup unit to the system BT Versatility Connecting the BatteryEnsure the battery switch on the BBU unit is turned off Led IndicatorsV16 Featurephone connections underside of phone FeaturephoneFeaturephone V8 Featurephone connections underside of phoneWall mount Plinth position Plinth position Plinth position Attaching the Featurephone desk plinth V8 andPosition at 20 degrees BT Versatility Feature phone with consoleV16 expansion console To connect the V16 Console to a Featurephone V16 onlyCord Rail Clip, Plinth and installation of the V16 expansion console15 cm cord RJ11 connector Line cord rails Wall-mounting a FeaturephoneDoor intercom bracket Mounting screw Door IntercomWall hook when the V8/V16 is in a 20 degrees or 35 degrees position Cabling the unit Connecting the extensionsD Data - LJU Pin Standard 4-Wire IDC Krone connectorA Speech - LJU Pin B Speech - LJU Pin C Data - LJU Pin Door Intercom Connecting a MOH Music On Hold ModuleCCU connections DoorstrikeBT Versatility Connecting a PA public Address amplifierConnecting a PC or Printer to the Serial Port Ports Module MDF ConnectionsBT Versatility Internet Module MDF ConnectionsExternal Extension Options Module MDF ConnectionsCentral Bell Expanding an Existing system Installing an additional Network Analogue or ISDN moduleInstalling additional modules Hot Swapping faulty modules Maintenance proceduresBT Versatility Replacing a faulty Module MDFReplacing the 008 extension board Replacing Faulty PCBsReplacing the CCU Control PCB BT Versatility Power supply unit spare fuseSpare Fuse Replacing the Power Supply UnitBT Versatility Replacing the CCU MDF ISDN Power failAnalogue Commissioning Power up and testSwitch on Incoming ringing ProgrammingBT Versatility Equipped exchange linesCall Barring BT VersatilityInternet Module Programming Installation WizardADSL BT Versatility ISDNRecommendations for customer training Troubleshooting 2 see above for system max Technical specification230 ± 10% V 50 Hz 2 see above for system maxref Pantone 432C BT VersatilityEN55022, EN55024, EN60950 CharcoalOptional software Full remote support from a BT Maintenance CentreINDEX PHME 42396/11/04 Offices Worldwide