Manuals / BT / Communications / Telephone

BT BT Versatility manual Mounting the Backplane, Securing the backplane to the wall bracket

Models: BT Versatility

1 59

Download 59 pages 3.62 Kb

Page 13

Image 13

BT Versatility

Installation and maintenance Manual

Mounting the Backplane

Slide the backplane on from the right hand side. Ensure the connector is fully mated with the CCU.

Securing the backplane to the wall bracket

A mounting screw is used to securely locate the backplane on the wall bracket. This provides additional rigidity to ensure the backplane and CCU connectors do not move.

Remove the fourth and fifth cover from the backplane.Locate the backplane on the bracket and connect it to the CCU. The backplane must be fully connected to the CCU to correctly locate the mounting screw hole. Insert the screw into the pillar on the bracket, which can be seen through the backplane mounting screw hole.

Mounting screw hole

Page 13

Image 13

BT BT Versatility manual Mounting the Backplane, Securing the backplane to the wall bracket

Contents

BT Versatility Installation and Maintenance ManualCommunications without the complications BT Versatility ContentsGeneral overview IntroductionElectrostatic precaution ESP Safety Precautions during installation and system upgradesLightning and surge voltage protection BT Versatility Voice Digital Includes System BT Versatility Pro. PlusIncludes System, VM, 1M,2V8BT Versatility Voice Analogue Inculdes System Versatility Value Add PacksBT Versatility Maintenance itemsTHIRD, install the Network and Expansion modules as required Installation checklistCCU LocationCCU Installing the Central Control UnitMounting the CCU 300mm CCU Mounting bracket clearances300mm min Mounting the CCUModule location Modules located in the CCUSystem Expansion Installing the Backplane wall bracketMounting the CCU with two brackets Securing the backplane to the wall bracket Mounting the BackplaneExpansion Modules BT Versatility Installing an Expansion modulePush up to lock Analogue line module Installing the Analogue Module in the CCUBT Versatility To Locate the Analogue Module in the Ports ModuleFirst network module Basic Rate ISDN expansion module Installing the Basic Rate ISDN Module in the CCUBT Versatility Digital Line Module ISDN First network moduleFirst network module To Locate the Digital Line Module ISDN 2 in the PORTS moduleT0 interface termination System ISDN settingsS0 interface termination Back up Voice Module voice messages and Greetings Voicemail moduleBT Versatility BT Versatility Primary Rate Interface Availability TBCConnecting the battery backup unit to the system Ensure the battery switch on the BBU unit is turned off Connecting the BatteryLed Indicators BT VersatilityV16 Featurephone connections underside of phone FeaturephoneFeaturephone V8 Featurephone connections underside of phonePosition at 20 degrees Attaching the Featurephone desk plinth V8 andWall mount Plinth position Plinth position Plinth position V16 expansion console Feature phone with consoleTo connect the V16 Console to a Featurephone V16 only BT Versatility15 cm cord RJ11 connector Clip, Plinth and installation of the V16 expansion consoleCord Rail Line cord rails Wall-mounting a FeaturephoneWall hook when the V8/V16 is in a 20 degrees or 35 degrees position Door IntercomDoor intercom bracket Mounting screw Cabling the unit Connecting the extensionsA Speech - LJU Pin B Speech - LJU Pin C Data - LJU Pin Standard 4-Wire IDC Krone connectorD Data - LJU Pin CCU connections Connecting a MOH Music On Hold ModuleDoorstrike Door IntercomConnecting a PC or Printer to the Serial Port Connecting a PA public Address amplifierPorts Module MDF Connections BT VersatilityBT Versatility Internet Module MDF ConnectionsCentral Bell Options Module MDF ConnectionsExternal Extension Installing additional modules Installing an additional Network Analogue or ISDN moduleExpanding an Existing system Hot Swapping faulty modules Maintenance proceduresBT Versatility Replacing a faulty Module MDFReplacing the 008 extension board Replacing Faulty PCBsReplacing the CCU Control PCB BT Versatility Power supply unit spare fuseBT Versatility Replacing the Power Supply UnitSpare Fuse Replacing the CCU MDF Analogue Power failISDN Switch on Power up and testCommissioning BT Versatility ProgrammingEquipped exchange lines Incoming ringingCall Barring BT VersatilityInternet Module Programming Installation WizardADSL BT Versatility ISDNRecommendations for customer training Troubleshooting 230 ± 10% V 50 Hz Technical specification2 see above for system max 2 see above for system maxEN55022, EN55024, EN60950 BT VersatilityCharcoal ref Pantone 432COptional software Full remote support from a BT Maintenance CentreINDEX PHME 42396/11/04 Offices Worldwide