SmartSwitch # add spvcaddress | Cabletron Systems 04-0053-01

Soft PVC and PVP Connections

Virtual Ports and Static Connections

3.Use the add spvcaddress command on the target switch to specify the target port and ATM address.

SmartSwitch # add spvcaddress
PortNumber()	: 6b3 — Port on target switch
AtmAddress()	: 22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22
Added SPVC Address successfully.
SmartSwitch #

Note Both soft PVCs and Soft PVPs use the add spvcaddress command to specify the target switch’s target ATM address. There is no separate “ add spvpaddress” command.

4.Use the show spvcaddress command to see the soft PVP port and ATM address on the target switch:

SmartSwitch # show spvcaddress
PortNumber(ALL)		:
TargetAddress()		:
Port	SPVC Target Address

================================================================================

6B3	22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22

Total number of SPVC Addresses = 1

SmartSwitch #

5.On the source switch, use the add trafficdescriptor command to create traffic descriptors for the forward and reverse directions of the connection (See Section 5.1.1for information about traffic descriptors).

6.On the source switch, use the add spvp command to create the soft PVP connection between the two switches:

SmartSwitch # add spvp
PortNumber()	: 7a1 — Port on source switch
SourceVpi(0)	: 3
DestinationSelectType(REQUIRED)	:	— See note below
DestinationVPI(0)	: 3	— We use VPI= 3
TargetAddress()	: 22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22:22
TransmitTrafficDescriptorIndex()	: 3
ReceiveTrafficDescriptorIndex()	: 3
RetryInterval(10000)	:
RetryLimit(3)	:
RetryThreshold(1)	:

SmartSwitch #

Note The DestinationSelectType determines which vpi is used on the target switch. The possible settings are REQUIRED and ANY. If DestinationSelectType is set to REQUIRED, the specified target vpi is set at the target switch. If ANY is specified, the soft PVP uses the first available vpi it finds on the target switch. If ANY is specified, enter the show spvptraget command on the target switch to determine the vpi used.

5-16 SmartSwitch ATM User Guide

Image 82

Cabletron Systems 04-0053-01 manual SmartSwitch # add spvcaddress, We use VPI=

Contents

SmartSwitch ATM Switch User Guide Part Number 04-0053-01 Rev. a Order Number Ii SmartSwitch ATM Switch User Guide FCC Class a Notice Manufacturer’s Address Application of Council DirectivesManufacturer’s Name Product Name Safety Information Class 1 Laser Transceivers Fiber Optic Protective Caps Regulatory Compliance Summary Safety Revision History Document Name Table of Contents Virtual Ports and Static Connections Index Table of Contents Xii SmartSwitch ATM User Guide List of Figures List of Figures Xiv SmartSwitch ATM User Guide List of Tables List of Tables Xvi SmartSwitch ATM User Guide Contents of the User Guide Introduction Smartswitch ATM Switch Differences IP address is for example only IP Over ATM and LaneCreating AN IP Over ATM Vlan Subnet mask is for example only Creating an IP over ATM Vlan IP Over ATM and Lane Default Netprefix for SmartSwitch Default ATM Addressing for IP over ATMDefault Netprefix for SmartSwitch 2500 Family Switches Default IP Over ATM Local Client Address Creating AN Emulated LAN Ilmi SmartSwitch 2500 Family Default Lane Addressing ATM Addressing for LAN Emulation Chassis MAC address = 0020D4144180 Then SmartSwitch 6500 Default Lane AddressingLecs address is constructed from CPU MAC address = 0020D4144180 Elan number = Then Chassis MAC address = 00001DA3870B Then ELANs Across Multiple SwitchesChassis MAC address = 00001DA3870B Elan number = Then Distributed Lane Services Switch ClientsJust for this example Use the add leselan command to create an LES on switch SW2 Specify the LES address on SW2 Best Effort Elan Join Test Elan Join PoliciesSW1 # show client By MAC Address By Route Descriptor Lecselanlec Table Weight the policy atUse ? to see possible types No MAC address is specified Lane Over WAN CircuitsPhysical Versus Logical BUS Multicasting Elan is specified by Elan number Single PVP connection between clients and Lane services Using Lnni Lane Service Redundancy Lane Load Sharing Lnni Redundant LECSs on same network Lnni call set up load sharing Setting up Lnni LECs How Lnni handles Elan join requests SW1 # set lnniinfo SW1 # stop lecsSW1 # stop les SW2# set lnniinfo SW1 # add elan On SW1, create an Elan in this example, we create elan1Similarly, create the same Elan elan1 on SW2 SW2 # add elan SW2 # show elan Configuring Lnni Distributed LES/BUS ServersSW1 # show lecsneighborinfo On switch SW3, use the set lnniinfo to configure Lnni SW3 # start les SW1 # show lecsserverlist LESPage SmartSwitch 6500 Family Default Node ID Default Pnni AddressingSmartSwitch 2500 Family Default Node ID Pnni Routing SmartSwitch 2500 Family Default Node ATM Address SmartSwitch 6500 Default Node ATM Address Connecting Multiple Peer Groups MULTI-LEVEL Pnni Topology SWA1 # set pnnipeergroupid Change the tenth byte to Specifies node number Do the same for switch SWB3Highest priority in election process SWB3 # set pnnipglelection Do the same on switch SWB3SWA3 # show pnnipglelection Physical Connections Between Peer Groups Adding Higher-level Peer Groups Adding a third Pnni node for next level connectivity SmartSwitch # show pnniinterface Managing Parallel Pnni Links 4a3 Link on switch SWB2 comes from this port Perform the same operation on switch SWB2 in group B7b2 Link on switch SWA2 comes from this port Aggregation Tokens Pnni Link Timing Aggregation token values and parallel links SmartSwitch # set linkmonitortimeout Iisp Routes RoutingAdditional Routing Protocols This is an exterior route Iisp Routing Considerations Iisp Routing Example One Iisp Routing Example Two Set linkmonitortimeout Iisp Link Timing Yes Take the default to make this an internal routeUNI Routes Advertise this address into the Pnni domain UNI Link Timing Route Metrics Administrative WeightsCreating Route Metrics Create the incoming member of the metric pair Create the outgoing member of the metric pairEnter show pnnimetric to view the newly created metric pair Index tag of our metric pair IP Routing for Management6b2 90.1.1.254 To see the route, enter the show route command on SW2 Route NET Table PVC Connections SmartSwitch # add trafficdescriptorVirtual Ports and Static Connections Point-to-Point PVCs Specify its Vpci Point-to-Multipoint PVCsSpecify first port Specify its VCI Perform for ports 7a3 and 7a4 Take the default valuesSet PCRCLP01 to zero Use add ipatmclient to create an IP over ATM local client Connecting to Local Switch Client Through a PVCConnect the end node to port 7a1 of the ATM SmartSwitch Set client number PVP Connections Turn off signalingTurn off Ilmi See note below Use the show pvp command to display the PVP connection7b1 Specify the first port Virtual Ports Connecting PVPs7a1.3, 5b2.3, A1.3, C5.3, and so on Creating Virtual Ports Available VPIs = 2MaxVpiBits Instance of set portconfig Default MaxVpiBits =Default MaxVciBits = Set to 1 this translates to VPIs = 2 1-1 = MaxVciBits decrements by .1 means our Base VPI is oneVPIs used = Base VPI + 2 0 1 = 1 + 0 = Specify virtual port number and Base VPI Soft PVC and PVP Connections Things To Watch Out For When Creating Virtual PortsSoft PVC and Soft PVP differences Making Soft PVC and PVP Connections Creating a soft PVC 6b3 Port on target switch SmartSwitch # add spvcaddressSmartSwitch # show spvcaddress 7a1 Port on source switch 102 Creating a Soft PVP We use VPI= SmartSwitch # show spvp PortNumberALL Soft PVC and PVP Connections Traffic Management Capabilities Traffic ManagementTraffic Descriptors PeakCellRate CLP0+1, PeakCellRate CLP0 No Traffic DescriptorPeakCellRate CLP0+1 PeakCellRate CLP0+1, PeakCellRate CLP0, Tag CLP = Call Admission Control Policy SmartSwitch # set cacserviceclassbw SmartSwitch # set caceqbwallocschemeUbr Queue Buffers CPU UBR Corresponds to CBR 7a3MinIndex for SmartSwitch # set switchtrafficcongestion SmartSwitch # show switchtrafficcongestionEFCI, EPD, and RM Cell Marking Traffic Management Capabilities Unsuccessful Update Firmware Upgrades and Bootline CommandsUpdate Firmware Commands IP address of Tftp server Enter the go command to start the ATM SmartSwitch Bootline Commands=df s Accessing the Bootline Prompt Bootline Commands Explanations Scsm Changes the slave TSM/CPU to the masterSwms Upgrading Boot Load firmware =df b =chpi Upgrading Post Diagnostic firmwareChanging the Default Boot Load Image =df p Upgrading Switch Operating firmware Bootline CommandsFirmware Upgrades and Bootline Commands Start the ATM SmartSwitch by entering the go command Bootline Commands Creating ATM Address Filters ATM Filtering and ClockingPort ATM Address Filters How ATM Address Filters Work ATM Address Filter Example Source and Destination Address Masks Filter Considerations Regarding Lane and IP over ATM Port Clock ConfigurationFFFFFFFFFFFFFFFFFFFF00000000000000000000 Network Clocking Troubleshooting Troubleshooting IP Over ATM Troubleshooting LAN Emulation Switches in Same Peer Group Troubleshooting Pnni LinksSwitches in Different Peer Groups Global Congestion Troubleshooting CongestionDiagnosing Congestion Fewer than 100 connections on a port Min = 64, Max = Port Congestion Events and Alarms Event Categories Viewing Events and Alarms SmartSwitch # set eventdisplay Deleting Events and Alarms SmartSwitch # set alarmdisplay Saving Core Dumps Login name on the serverPassword IP address of my Tftp server Saving Core Dumps Appendix a Agent Support MIB, SMI, MIB Files and Internet MIB Hierarchy CSI ZeitNet Proprietary MIBs MIB, SMI, MIB Files and Internet MIB Hierarchy Relation Between Object Identifier and the Represented Value Supported SMI Formats Supported protocolsCSI ZeitNet Proprietary MIB Groups Ctron MIB Exceptions ATM SmartSwitch MIB SupportNon-Conformance Console Commands that Affect the Agent Managing AN ATM SmartswitchNot Supported Default Community Strings Update firmware Backup Restore Reboot Appendix B Technical Support FAX ServiceElectronic Services Telephone Assistance Software Warranty Hardware WarrantyRepair Services Accessing the boot load prompt Index 12,4-4,4-6 Fail-over timing Route type parameter Iisp routing considerations ZnPortTrafficCongTable ZnSwitchDiscoveryTableMulti-level Pnni topology PNN Changing EPD thresholds Enabling RM cell marking Vlan