Upflowdownflow Horizontal | Carrier 58PHA/PHX manual

UPFLOWDOWNFLOW HORIZONTAL

90°

YES

120°	YES
MIN

NO

OUTER DOOR

ASSEMBLY

8" (203mm) MIN

FOR DOOR REMOVAL

(2)HEX NUTS, (2) WASHERS & (2) LOCK WASHERS REQ. PER ROD

90°

YES	YES

120°	YES	120°	YES
MIN		MIN

NO

NO

A02020

Fig. 14 - Duct Flanges

1/4" (6mm) THREADED ROD

4 REQ.

SECURE ANGLE

IRON TO BOTTOM

OF FURNACE WITH

3 #8 x 3/4" (19mm) SCREWS TYPICAL FOR 2 SUPPORTS

1” (25mm) SQUARE, 1-1/4”x1-1/4”x1/8” (32x32x3mm)

ANGLE IRON OR UNI-STRUT MAY BE USED

58PHA

A05027

Fig. 15 - Horizontal Unit Suspension

15

Image 15

Carrier 58PHA/PHX instruction manual Upflowdownflow Horizontal

Contents

Ama Furnace Reliability Hazard Safety Considerations CUT Hazard Introduction Clearances to Combustibles Codes and Standards Venting Electrostatic Discharge ESD Precautions Procedure Location GeneralCarbon Monoxide Poisoning Hazard Personal Injury AND/OR Property Damage Hazard Electrical Operation Hazard Location Relative to Cooling Equipment AIR for Combustion VentilationFire Hazard Furnace Corrosion Hazard ACH Side Return Air Inlet InstallationCombination of Indoor and Outdoor Air Bottom Return Air Inlet Leveling Legs Downflow Installation A08556 Roll-Out Protection Opening Dimensions In. mmSuspended Furnace Support Platform Furnace Support Ductwork Acoustical Treatment Supply Air Connections Filter Arrangement Carbon Monoxide and Poisoning HazardAIR Ducts General Requirements Upflowdownflow Horizontal Horizontal Suspension with Straps Return Air Connections GAS Piping Fire or Explosion HazardFurnace Overheat Hazard Maximum Capacity of Pipe Air Delivery CFM With Filter Upflow Return Air Configurations and Restrictions Horizontal Return Air Configurations and Restrictions Electrical Data Electrical Connections Electrical Shock HazardElectrical Shock and Fire Hazard Electrical Connection to J-BOX WiringFurnace MAY not Operate BOX Relocation Venting Power Cord Installation in Furnace J-BOXBX Cable Installation in Furnace J-BOX Accessories Furnace Control Masonry Chimney Requirements General Venting Requirements Single-Stage Furnace with Single-Speed Air Con Ditioner Humidfier Internal Area of Chimney Appliance Application Requirements Chimney Inspection Chart Additional Venting Requirements Burn HazardSidewall Venting Upflow Application-Vent Elbow Up See Notes 1,2,4,5,7,8,9 on See Notes 1,2,4,5,7,8,9 Venting Notes for Figures Using Tin Snips to Cut Tie Points Rounded End of Knockout START-UP, ADJUSTMENT, and Safety Check Fire and Explosion HazardFurnace Damage Hazard Canada Follow exclusively the National Fuel Gas CodeAltitude Derate Multiplier for U.S.A Gas Control Valve Check Safety Controls Speed SelectionFurnace Overheating Hazard Gas Rate Cu Ft./Hr Checklist A08220 A08220A Electrical SHOCK, Fire or Explosion Hazard Service and Maintenance ProceduresElectrical Controls and Wiring Electrical Shock Hazard FIRE, INJURY, or Death Hazard A08221 Service Filter Size Information In. / mm Care and Maintenance Fire or Explosion HazardCleaning AND/OR Replacing AIR Filter Carbon Monoxide Poisoning Fire Hazard Unit Damage Hazard Cleaning Heat Exchanger Igniter Position-Side View Sequence of Operation Cleaning Heat Exchanger Cell Two-Speed Cooling Cooling ModeThermidistat Mode Continuous Blower Mode Wiring Diagrams TroubleshootingHeat pump Wiring Diagram Troubleshooting Guide Catalog No 58PHA---03SI