CTK691E01-01.book 88 ページ 2003年9月29日 月曜日 午後4時47分

DSP Algorithm List

00 :Auto Pan

ŠFunction

Continually performs left-right panning of the input signal in accordance with an LFO.

ŠParameters

0 : Rate (Range: 0 to 127) Adjusts the panning rate.

1 : Depth (Range: 0 to 127) Adjusts the panning depth.

01:Tremolo

ŠFunction

Adjusts volume of input signal in accordance with an LFO.

ŠParameters

0 : Rate (Range: 0 to 127) Adjusts the tremolo rate.

1 : Depth (Range: 0 to 127)

Adjusts the tremolo depth.

0 : Low Frequency (Range: 0 (200Hz), 1 (400Hz), 2 (800Hz))

Adjusts the cutoff frequency of the low-band equalizer.

1:Low Gain (Range: –12, –11, –10 to 0 to +10, +11, +12)

Adjusts the gain of the low-band equalizer.

2:Mid Frequency (Range: 0 (1.0KHz), 1 (1.3KHz), 2 (1.6KHz), 3 (2.0KHz), 4 (3.0KHz), 5 (4.0KHz), 6 (6.0KHz), 7 (8.0KHz))

Adjusts the center frequency of the mid-band equalizer.

3:Mid Gain (Range: –12, –11, –10 to 0 to +10, +11, +12)

Adjusts the gain of the mid-band equalizer.

4:High Frequency (Range: 0 (6.0KHz), 1 (8.0KHz), 2 (10KHz))

Adjusts the cutoff frequency of the high-band equalizer.

5:High Gain (Range: –12, –11, –10 to 0 to +10, +11, +12)

Adjusts the gain of the high-band equalizer.

02:2BandEQ

ŠFunction

This is a two-band equalizer.

ŠParameters

0: Low Frequency (Range: 0 (200Hz), 1 (400Hz), 2 (800Hz))

Adjusts the cutoff frequency of the low-band equalizer.

1: Low Gain (Range: –12, –11, –10 to 0 to +10, +11, +12)

Adjusts the gain of the low-band equalizer.

2: High Frequency (Range: 0 (6.0KHz), 1 (8.0KHz), 2 (10KHz))

Adjusts the cutoff frequency of the high-band equalizer.

3: High Gain (Range: –12, –11, –10 to 0 to +10, +11, +12)

Adjusts the gain of the high-band equalizer.

03:3BandEQ

ŠFunction

This is a three-band equalizer.

ŠParameters

04 :LFO Wah

ŠFunction

This is a “wah” effect that can automatically affect the frequency in accordance with an LFO.

ŠParameters

0:Input Level (Range: 0 to 127)

Adjusts the input level. The input signal can become distorted when the level of the sound being input, the number of chords, or the Resonance value is large. Adjust this parameter to eliminate such distortion.

1:Resonance (Range: 0 to 127) Adjusts the resonance of the sound.

2:Manual (Range: 0 to 127)

Adjusts the frequency used as the basis for the wah filter.

3:LFO Rate (Range: 0 to 127) Adjusts the rate of the LFO.

4:LFO Depth (Range: 0 to 127) Adjusts the depth of the LFO.

05 :Auto Wah

ŠFunction

This is a “wah” effect that can automatically affect the frequency in accordance with the level of the input signal.

E-88

705A-E-090A