Using Built-in Tones (Tutorial)
3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| en | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 5 6 7 8 9 | cm cn co cp | dk | dr ds dt ek el em ep |
You can use the editing procedures explained in this section to edit tones and apply effects as desired. After editing a tone, you can give it a name and save it as a user tone.
•For information about tone editing, see “To edit a tone” (page
•For information about applying an effect (DSP and/ or system effect) to a tone, see “Applying Effects to Notes” (page
•To change the effects and/or functions assigned to wheel, knob, and slider operations, see “Using the Stage Setups (Tutorial)” (page
To edit a tone
1. Specify the number of the tone you want to edit.
2. Press the ep (EDIT) button.
This displays the editing screen.
3. Use the dt (w) and ek (q) buttons to select “Tone”, and then press the em (ENTER) button.
4. Use the ds (u), dt (w), ek (q), and el (i) buttons to select a setting item.
•If “>ENT” is on the display, it means that there are more setting items that can be edited in the operation you are performing. In this case, pressing the em (ENTER) button will advance to the next editing page.
•The setting items that appear on the editing screen depend on the tone you select.
•For information about editable parameters, see the explanations about each tone category from “Editable Melody Tone Parameters” (page
5.Change parameters as desired.
6.After you finish with your edits, press the dr (EXIT) button.
•Press the dr (EXIT) button as many times as required to return to the screen where you were before you started editing.
To change the name of a tone
1. Perform steps 1 through 3 of the procedure under “To edit a tone”, above.
2. Use the ds (u), dt (w), ek (q), and el (i) buttons to select “NameEdit”, and then press the em (ENTER) button.
3. Change the name.
4. After you finish with your edits, press the dr (EXIT) button.
•Press the dr (EXIT) button as many times as required to return to the screen where you were before you started editing.