Using Built-in Tones (Tutorial)

■Editable SYSTEM Parameters

•Parts 5 through 16 do not support use of resonance effects.

System Chorus

Parameter Value Ranges:

1:Type (Light Cho, Chorus, FB Chorus, Flanger) Selects the chorus type.

2:LFO Rate (0 to 127)

Adjusts the LFO rate.

3:LFO Depth (0 to 127) Adjusts the LFO depth.

4:Feedback (0 to 127)

Adjusts the feedback amount.

5:Tone (0 to 127) Adjusts the tone.

6:Delay Time (0 to 127) Adjusts the delay time.

7:Delay Send (0 to 127)

Adjust the send level to system delay.

8 :Reverb Send (0 to 127)

Adjust the send level to system reverb.

9:Return (0 to 127) Adjusts the return level.

System Delay

Parameter Value Ranges:

1 :Time (0 to 127)

Adjusts the total delay time.

2 :Feedback (0 to 127)

Adjusts the feedback amount.

3 :High Damp (0 to 127)

Adjusts the high-range damp. A larger number increases damping.

4 :Ratio L (0 to 127)

Adjusts the ratio of the left channel relative to the total delay time.

5 :Ratio C (0 to 127)

Adjusts the ratio of the center channel relative to the total delay time.

6 :Ratio R (0 to 127)

Adjusts the ratio of the right channel relative to the total delay time.

7 :Level L (0 to 127)

Adjusts the level of the left channel.

8 :Level C (0 to 127)

Adjusts the level of the center channel.

9 :Level R (0 to 127)

Adjusts the level of the right channel.

10:Tempo Sync (Off, 1/4, 1/3, 3/8, 1/2, 2/3, 3/4, 1, 4/3, 3/2, 2) Specifies how the actual total delay time is synced with tempo.

•Off: Uses Delay Time value.

•1/4 to 2: Uses value in accordance with number of beats.

11:Reverb Send (0 to 127)

Adjust the send level to system reverb.

12:Return (0 to 127) Adjusts the return level.

System Reverb

Parameter Value Ranges:

1:Type (Room, Hall1, Hall2, Plate) Selects the reverb type.

2:Time (0 to 127)

Adjusts the reverb time.

3 :Early Reflection (0 to 127)

Adjusts the level of the initial reflection.

4 :High Damp (0 to 127)

Adjusts the high-range damp. A larger number increases damping.

5:Tone (0 to 127) Adjusts the tone.

6:Return (0 to 127) Adjusts the return level.

System Resonance

Parameter Value Ranges:

1 :String Reso Send (0 to 15)

Adjusts the send level to string resonance.

2 :Damper Reso Send (0 to 15)

Adjusts the send level to damper resonance.

3:Damper Noise Enable (Off, On) Enables/disables the damper noise effect.

■Editable MASTER Parameters

Master Compressor

Parameter Value Ranges:

1 :Threshold (0 to 127)

Adjusts the threshold (where application of an effect starts) level. Set a lower value for a compressor effect, and a higher value for a limiter effect.

2 :Ratio (0 to 127)

Adjusts the compression ratio.

Set a lower value to for a compressor effect, and the maximum value to for a limiter effect.

3:Level (0 to 127) Adjusts the output level.

4:Attack (0 to 127)

Adjusts the time until the compression effect starts.

A smaller value causes prompt compressor operation, which suppresses the attack of the input signal. A larger values delays compressor operation, which causes the attack of the input signal to be output as-is.

5:Release (0 to 127) Adjusts the release time.

Adjusts the time until the compression effect is released.

6:Position (PreEQ, PostEQ)

Selects the connection position with the compressor and EQ.

Master Equalizer

Parameter Value Ranges:

1:Low Gain (–12 to 0 to +12) Adjusts the low-range gain.

2:Low Frequency (200, 400, 800 [Hz]) Selects the low-range cutoff frequency.

3:Mid 1 Gain (–12 to 0 to +12)

Adjusts the low mid-range gain.

4 :Mid 1 Frequency

(1.0k, 1.3k, 1.6k, 2.0k, 2.5k, 3.2k, 4.0k, 5.0k [Hz]) Selects the low mid-range frequency.

5:Mid 2 Gain (–12 to 0 to +12) Adjusts the high mid-range gain.

6:Mid 2 Frequency

(1.0k, 1.3k, 1.6k, 2.0k, 2.5k, 3.2k, 4.0k, 5.0k [Hz]) Selects the high mid-range frequency.

7:High Gain (–12 to 0 to +12) Adjusts the high-range gain.

8:High Frequency (6.0k, 8.0k, 10k [Hz]) Selects the high-range cutoff frequency.

9:Input Level (0 to 127)

Adjusts the input level.

10:Output Level (0 to 127) Adjusts the output level.

E-23