Casio PX-5S (K1), (ZONE), (TEMPO), (ENTER), Settings, Description, Display Text

Using the Stage Setups (Tutorial)

	Display Text			Description	Settings
			Master effect parameter. This is a group of editable master effect parameters
Master Effect Edit >Ent			(page E-23). For details about group items, see “Editable MASTER
			Parameters” (page E-23).
	Compressor Edit		Compressor edit. This is a group of editable compressor parameters within
	>Ent		master effects.
	Equalizer Edit >Ent		Equalizer edit. This is a group of editable equalizer parameters within
			master effects.
Common Edit >Ent			This is a group of editable pedal, PRN, and NPRN parameters.
	Tempo		Tempo. Adjusts the phrase playback speed. You also can change the phrase		20 - 255
			playback tempo using the ct (TEMPO) button.
	Phrase		Phrase number. Selects the phrase of the Phrase Sequencer (page E-29).		U000 - U999
	Arpeggio		Preset arpeggio type selection. See “To use the Arpeggio Function” in the		Off, On, Hold
			separate USER’S GUIDE (Basics).
	Hammer Response		Hammer response. Adjusts hammer response within the range of 0 (fast) to		0 - 7
			7 (slow).
	Knob1 Edit >Ent		Knob 1 (Knob 1 edit). This is a group of 3 (K1) knob editable parameters.
			Editing can be performed even when the “Knob 1 Enable” setting is “Off”.
			Target. Selects the parameters to be controlled by a controller. For example,
			the “CC67:Soft” setting specifies a soft pedal effect.
			• Two targets can be specified for a single controller. Use the dk (ZONE)
				minus (–), plus (+) buttons to switch between Target 1 and Target 2.
			No Assign: No target specified.
			CC00 to CC97: MIDI control change*1
			NRPN, RPN: MIDI NRPN and RPN parameters*1 *2
			Ch.Pressure: MIDI channel pressure*1
			Tempo: Tempo setting (page E-30)
			EQ Low Gain - EQ High Gain: Master EQ >Low Gain - High Gain (page
			E-23)
			DSP Bypass: Temporarily bypasses the DSP of the currently selected zone.
			Ext.Volume: Control the External Volume value.
			Layer Detune: Layer detune (page E-17)
			Layer1 Volume - Layer6: Tone parameter settings of each layer
			• The following can be assigned: Volume (Volume), Pan (panning), OctShift
				(octave shift), DspOnOff (DSP on/off), LfoPitch (LFO pitch), LfoFiltr (LFO
		Target		filter), LfoAmp (LFO amp). For details about each setting, see the editable	Refer to the cell to the
				parameters under “Using Built-in Tones (Tutorial)” on page E-10.	left.
			Dsp Param 1-16: DSP parameters
			Pedal1 On Rate, Pedal1 Off Rate, Pedal2 On Rate, Pedal2 Off Rate: on value,
			on rate, off value, off rate for each pedal*3
			Arp Hold On/Off: Arpeggio hold setting*4
			Song Str/Stp: Song sequencer playback start/stop*4
			Phrase Str/Stop: Phrase playback start/stop*4
			Audio Str/Stop: Audio playback start/stop*4
			*1	For details about each setting, see the MIDI Implementation Chart
			*2	(http://world.casio.com/) and/or MIDI documentation.
				After selecting these setting items, press the em (ENTER) button again
				and then adjust the items below.
				MSB: 63H for NRPN, 65H for RPN (Setting range: 000 to 127)
				LSB: 62H for NRPN, 64H for RPN (Setting range: 000 to 127)
				Send Data: Specifies whether knob operation controls MSB or LSB
				value. (Settings: MSB, LSB)
			*3	This setting is not supported for Damper/Pedal 1 (Pedal 1) or Pedal 2.
			*4	This setting is supported for Damper/Pedal 1 (Pedal 1) and Pedal 2 only.
		Min Value	Minimum value. Controller minimum output value setting.		0 - 127
		Max Value	Maximum value. Controller maximum output value setting.		0 - 127
			Knob 2 to 4 (Knob 2 to 4 edit). This is a group of 3 Knob (K2) through (K4)
	Knob2-4 Edit >Ent		editable parameters. Editing can be performed even when the “Knob 2-4
			Enable” setting is “Off”. Details of editable parameters are the same as
			“Knob1 Edit >Ent”, above.

E-34