Performing
|
|
|
|
|
| Table 5 |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| Task |
|
| Notes | ||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| If you plan to install Cisco CallManager Release |
| See the “Uninstalling Microsoft Hotfix 831877” | |||
|
|
|
|
|
| 3.3(2) or 3.3(3), uninstall the |
| section on page 22. | |||
|
|
|
|
|
| Microsoft hotfix 831877 that the operating system |
|
|
|
| |
|
|
|
|
|
| includes. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| Subscribe to the Cisco Unified CallManager |
| This task enables you to receive | |||
|
|
|
|
|
| Notification Tool and PSIRT notification tool. |
| notification whenever new fixes, operating system | |||
|
|
|
|
|
|
|
|
| updates, and service releases become available. | ||
|
|
|
|
|
|
|
|
| See the “Applying Additional Security” section | ||
|
|
|
|
|
|
|
|
| on page 23. | ||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| Increase the security on your server. |
| See the “Applying Additional Security” section | |||
|
|
|
|
|
|
|
|
| on page 23. | ||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| If your hardware supports network teaming (HP |
| Refer to Using the Cisco Media Convergence | |||
|
|
|
|
|
| only), enable the Cisco Media Convergence |
| Server Network Teaming Driver for a list of | |||
|
|
|
|
|
| Server (MCS) Network Teaming Driver to support |
| supported servers and installation information. | |||
|
|
|
|
|
| the functionality for the failover, |
|
|
|
| |
|
|
|
|
|
| network adapters. |
|
|
|
| |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| Configure the speed and duplex of your network |
| Refer to Using the Cisco Media Convergence | |||
|
|
|
|
|
| card to 1000/Full if the hardware on your server |
| Server Network Teaming Driver. | |||
|
|
|
|
|
| and network supports gigabit speed. |
|
|
|
| |
|
|
|
|
|
| ||||||
Configuring Network Settings |
|
|
| ||||||||
|
|
|
|
|
|
|
|
| |||
|
|
|
| Tip | Cisco recommends that you configure static IP information, which ensures that the Cisco Unified | ||||||
|
|
|
|
|
| CallManager server obtains a fixed IP address. With this choice, Cisco Unified IP Phones can register | |||||
|
|
|
|
|
| with Cisco Unified CallManager when you plug the phones into the network. | |||||
|
|
|
|
|
| If you choose to use Dynamic Host Configuration Protocol (DHCP), Cisco Technical Assistance Center | |||||
|
|
|
|
|
| (TAC) requires that you reserve an IP address for each server in the DHCP server scope. This action | |||||
|
|
|
|
|
| prevents the release or reassignment of IP addresses. If you do not reserve IP addresses through the | |||||
|
|
|
|
|
| DHCP server scope, the DHCP server may assign a different address to the server if the server is | |||||
|
|
|
|
|
| disconnected from, and then reconnected to, the network. To return the server to its original IP address, | |||||
|
|
|
|
|
| you must reprogram the IP addresses of the other devices on the network. | |||||
|
|
|
|
|
| For other information on configuring network settings, see the “What data must I provide to configure | |||||
|
|
|
|
|
| the server?” section on page 9. |
|
|
| ||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| To configure network settings on the server, perform the following procedure: | |||||
|
|
|
|
|
| Procedure |
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
| Step 1 | On the desktop, right click My Network Connections and choose Properties. | |||||||
|
|
| Step 2 | Although the server comes with two Network Interface Cards (NIC), Cisco recommends that you | |||||||
|
|
|
|
|
| configure the network settings on the first NIC. To configure network settings on the first NIC on the | |||||
|
|
|
|
|
| server, click Internet Protocol (TCP/IP); then, click Properties. | |||||
|
|
| Installing the Operating System on the Cisco Unified Communications Server, Versions 2000.4.3 and 2000.4.3a | ||||||||
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| 20 |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |||
