Summary of the available interfaces appears | Cisco Systems 2800

Step 6 Enter the virtual terminal password, which prevents unauthenticated access to the router through ports other than the console port:

The virtual terminal password is used to protect access to the router over a network interface. Enter virtual terminal password: xxxxxx

Step 7 Respond to the following prompts as appropriate for your network:

Configure SNMP Network Management? [yes]:

Community string [public]:

A summary of the available interfaces appears:

Note The interface numbering that appears is dependent on the type of Cisco modular router platform and on the installed interface modules and cards.

Current interface summary
Controller		Timeslots	D-Channel Configurable modes		Status
T1	0/0/0	24	23	pri/channelized	Administratively up
T1	0/0/1	24	23	pri/channelized	Administratively up
T1	0/2/0	24	23	pri/channelized	Administratively up
T1	0/2/1	24	23	pri/channelized	Administratively up

Any interface listed with OK? value "NO" does not have a valid configuration
Interface	IP-Address	OK?	Method	Status	Protocol
GigabitEthernet0/0	20.0.0.40	YES	DHCP	up	up
GigabitEthernet0/1	unassigned	NO	unset	up	up
GigabitEthernet0/3/0	unassigned	NO	unset	up	up

Step 8 Choose one of the available interfaces for connecting the router to the management network:

Enter interface name used to connect to the

management network from the above interface summary: fastethernet0/0

Step 9 Respond to the following prompts as appropriate for your network:

Configuring interface FastEthernet0/0:

Use the 100 Base-TX (RJ-45) connector? [yes]: yes

Operate in full-duplex mode? [no]: no

Configure IP on this interface? [yes]: yes

IP address for this interface: 172.1.2.3

Subnet mask for this interface [255.255.0.0] : 255.255.0.0

Class B network is 172.1.0.0, 16 subnet bits; mask is /16

Step 10 The configuration is displayed:

The following configuration command script was created:

hostname Router

enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1 enable password xxxxxx

line vty 0 4 password xxxxxx

snmp-server community public

!

no ip routing

!

interface FastEthernet0/0 no shutdown

media-type 100BaseX half-duplex

ip address 172.1.2.3 255.255.0.0

!

34

Image 34

Cisco Systems 2800 manual Summary of the available interfaces appears

Contents

Including License and Warranty Duration of Hardware Warranty Cisco 90-Day Limited Hardware Warranty TermsReplacement, Repair, or Refund Policy for Hardware To Receive a Return Materials Authorization RMA Number Overview Product Serial Number Location Serial Number Label Location for Cisco 2801 Router Items Included with Cisco 2801 Routers Documents, Equipment, and ToolsUser Documentation Translated Versions Safety Information Install ChassisItems Not Included Page OBS! Spara Dessa Anvisningar Guarde Estas Instruções GEM Disse Anvisninger Page Installing the Router Statement Rack-Mounting the Router Attaching Brackets to the Router for Rack-Mounting Bracket Installation for Front Mounting Installing the Router in a Rack Wall-Mounting the Router-Cisco 2811 Routers Only Attaching Brackets to the Router for Wall Mounting Grounding the Chassis Installing the Router on a DesktopGround during normal use. Statement Chassis Ground Connection on Cisco 2801 Chassis Connect Cables Protective device is rated not greater than Power ConnectionsConnecting the Router to AC Power 120 VAC, 15 a 240 VAC, 10 A. Statement 60 VDC, 20 A. Statement Connecting the Router to DC PowerSize Wire Terminal Lug Protection Use copper conductors only. Statement Step TipInsulation and conductor. Statement Be connected first and disconnected last. Statement DC Wire Routing and Attachment for Cisco 2811 Routers Electrical hazards. Statement Connecting to One Source Only-Source a or Source B Source a and Source B Wired with Opposite-Polarity Grounds Connecting the Router to Backup Power WAN, LAN, and Voice Connections Port or Connection Port Type, Color Cable T1/E1 WAN System Management Connections Power Up the RouterChecklist for Power-Up Port Color Connection Cable Power-Up Procedure Verify the Front Panel LED Indications Verify the Hardware ConfigurationInterface Numbering LED Label LED Color or State Meaning Slot Type Interface Numbering Range Port Location Interface Numbering Scheme Examples1 Perform Initial Configuration Initial Configuration Using the Setup Command Facility Summary of the available interfaces appears User prompt appears To access documentation on Cisco.com Where to Go NextVerify the Initial Configuration To access documentation using Cisco Connection Online CCO Product Documentation DVD Obtaining DocumentationCisco.com Ordering Documentation Documentation Feedback Reporting Security Problems in Cisco ProductsCisco Product Security Overview Obtaining Technical Assistance Submitting a Service RequestDefinitions of Service Request Severity Cisco Technical Support & Documentation Website Obtaining Additional Publications and Information Page Page Page Page USA