Manuals / Cisco Systems / Power Tools / Router

Cisco Systems AIRCAP3602IAK9 manual General Site Requirements, Power Supply Considerations

Models: AIRCAP3602IAK9

1 146

Download 146 pages 14.51 Kb

Page 39

Chapter 2 Preparing to Install the Router

General Site Requirements

General Site Requirements

This section describes the requirements your site must meet for safe installation and operation of your router. Ensure that the site is properly prepared before beginning installation. If you are experiencing shutdowns or unusually high errors with your existing equipment, this section can also help you isolate the cause of failures and prevent future problems.

Power Supply Considerations

Check the power at your site to ensure that you are receiving “clean” power (free of spikes and noise). Install a power conditioner if necessary.

Warning The device is designed for connection to TN and IT power systems. Statement 1007

The AC power supply includes the following features:

•Autoselects either 110-V or 220-V operation.

•All units include a 6-foot (1.8-meter) electrical power cord. (A label near the power cord indicates the correct voltage, frequency, current draw, and power dissipation for the unit.)

Table 2-1describes power requirements for Cisco 3600 series routers.

Table 2-1 Power Requirements for Cisco 3600 Series Routers

Router	Power Supply	Input Power				Input Voltage
						Tolerance Limits

Cisco 3620	AC	100 - 240 VAC, 1.0 A, 50 - 60 Hz				85	- 264 VAC

	DC, nominal 48 VDC	48	- 60 VDC, 3.0 A, positive or negative input			38	- 72 VDC

Cisco 3631	AC	100 - 240 VAC, 2.0 A, 50 - 60 Hz				85	- 264 VAC

	DC, nominal 24/48 VDC	24	- 36 VDC, 8 A, positive or negative input			18	- 72 VDC

		36	- 60 VDC, 4 A, positive or negative input

	DC, nominal 48 VDC	48	- 60 VDC, 4		A, positive or negative input	38	- 72	VDC

Cisco 3640	AC	100 - 240 VAC, 2.0 A, 50 - 60 Hz				85	- 264 VAC

	DC, nominal 48 VDC	48	- 60	VDC, 5.0 A, positive or negative input		38	- 72	VDC

Cisco 3660	AC	100 - 240 VAC, 4.0 A, 50 - 60 Hz				85	- 264 VAC

	DC, nominal 24/48 VDC	24	- 36	VDC, 16 A, positive or negative input		18 - 72		VDC

		36	- 60	VDC, 7	A, positive or negative input

	DC, nominal 48 VDC	48	- 60	VDC, 8	A, positive or negative input	38	- 72	VDC

Cisco 3600 Series Routers Hardware Installation Guide

	OL-2056-05	2-3

Image 39

Cisco Systems AIRCAP3602IAK9 manual General Site Requirements, Power Supply Considerations

Contents

Corporate Headquarters Cisco 3600 Series Routers Hardware Installation GuideCisco 3600 Series Routers Hardware Installation Guide N T E N T S Creating a Site Log Connecting Routers to the Cisco Redundant Power System Troubleshooting A-1 Objectives PrefaceChapter Title Description AudienceOrganization ConventionsBewaar Deze Instructies Safety WarningsAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseGuarde Estas Instruções Aviso Instruções Importantes DE SegurançaGEM Disse Anvisninger Xiii Related Documentation Cisco Product Document Title Cisco 90-Day Limited Hardware Warranty Terms Duration of Hardware WarrantyReplacement, Repair, or Refund Policy for Hardware Documentation CD-ROM To Receive a Return Materials Authorization RMA NumberObtaining Documentation Cisco.comCisco TAC Website Documentation FeedbackObtaining Technical Assistance Ordering DocumentationTAC Case Priority Definitions Opening a TAC CaseObtaining Additional Publications and Information Overview of Cisco 3600 Series Routers Hardware FeaturesCisco Front Panel of the Cisco 3640 Router Front Panel of the Cisco 3660 Router Cisco 3662 Router with Two Fast Ethernet Interfaces Modules and Interface CardsMemory Memory Installation DocumentationMemory Specifications Description Specification55 KB Unit Numbering Interface NumberingCisco 3620 and Cisco 3640 Interfaces Slot NumberingCisco 3631 Interfaces Voice Interface NumberingWAN and LAN Interface Numbering Interface Numbering-Example Cisco 3660 Slot Numbers Cisco 3660 InterfacesRegulatory Compliance and Safety Information document that System SpecificationsCisco 3631 Router System Specifications Cisco 3640 Router System Specifications Regulatory Compliance OL-2056-05 Safety with Electricity Safety RecommendationsPreventing Electrostatic Discharge Damage General Site Requirements Power Supply ConsiderationsSite Environment Site ConfigurationEquipment Racks Task Verified by Date Installation ChecklistInspecting the Router Creating a Site LogTools and Equipment for Installation and Maintenance Console and Auxiliary Port Considerations Console Port ConnectionsAuxiliary Port Connections Ethernet Connections Preparing to Connect to a NetworkSerial DTE or DCE Devices Configuring Serial ConnectionsToken Ring Connections Serial ConnectionsSignaling Standards Supported Distance LimitationsDevice Type Gender Typical Devices Distance EIA-530 Distance Rate bps Feet Meters Isdn BRI ConnectionsAsynchronous/Synchronous Serial Module Baud Rates EIA/TIA-232Low-Capacitance Cable 56-K/Switched-56-kbps DSU/CSU ConnectionsInstalling the Router Installing Modules, Interface Cards, and Power Supplies Installing the Chassis Setting the Chassis on a DesktopRack-Mounting the Chassis Right Cisco 3640 Rack-Mount Brackets Attaching Brackets to the RouterFront-Panel-Forward Installation Use two screws on each side 17327 Rear-Panel-Forward Installation Four screws are required on each side 82808 Center-Mount Installation 22 Cisco 3660 Center-Mount Bracket Attachment Mounting the Router in the Rack Inch rack 24-inch rack 26 Mounting the Cisco 3631 Router 19-Inch Rack 28 Mounting the Cisco 3660 Router 19-Inch Rack Mounting the Router on the Wall Wall-Mounting the Cisco 3620 RouterAttaching Rubber Feet to the Router Attaching Wall-Mount Brackets to the RouterCisco 3620 and Cisco 3640 Chassis Ground Connection Installing Chassis Ground ConnectionMounting Screws Power supply Bracket NEBS-Compliant Ground Lug Attachment on a Cisco 3640 Router Ring terminal attached to a bracket Power supply Ring terminal Ground lug attachment Cisco 3631 Chassis Ground ConnectionCisco 3660 Chassis Ground Connection 103013 15A, 120VAC 10A, 240VAC. Statement Power ConnectionsConnecting Routers to AC Power Connecting Routers to a DC-Input Power SupplyDC Input DC Input Wire Size DC Wiring Requirements43 DC Power Connections for Cisco 3620 Routers Typical Wiring the DC-Input Power Supply in Cisco 3631 Routers DC InputOvercurrent 45 DC Power Connections for -DC Input to Cisco 3631 Routers 47 Wire Routing and Attachment for Cisco 3631 Routers Wiring the DC-Input Power Supply in Cisco 3660 RoutersDC Input Wire Size Method Protection Wire Termination Safety Ground OvercurrentReturn Safety ground Wire management bracket Connecting Routers to the Cisco Redundant Power System Ports and Cabling Connecting WAN, LAN, and Voice CablesT1/E1 WAN Port or Connection Port type, color Connected to CableConnections for Cisco 3660 Routers Connecting WAN, LAN, and Voice Cables Without Chassis ShieldLAN, WAN, and voice cables Power wires 54 Removing Panels from Chassis Shield 55 Cables Routed Through Openings in the Chassis Shield 56 Cables Routed Through the Chassis Cutout Connecting to a Console Terminal or Modem57 Connecting a Console Terminal to a Cisco 3620 Router Connecting to the Console Port58 Connecting a Console Terminal to a Cisco 3631 Router 60 Connecting a Console Terminal to a Cisco 3660 Router Connecting to the Auxiliary PortModem Modem cable AUX port Connector RJ-45 RJ-45-to-RJ-45 rollover cable 65 Identifying a Rollover Cable Identifying a Rollover CablePowering Up the Router Checklist for Power UpFront Panel Indicators Cisco 3620 series and Cisco 3640 series Power-Up ProcedureInitial Configuration Using SDM Configuring the RouterInitial Configuration Using the Setup Command Facility Summary of the available interfaces is displayed User prompt appears Enter privileged Exec mode Initial Configuration Using the CLI Manual ConfigurationOL-2056-05 Isolating Problems TroubleshootingTroubleshooting the Power and Cooling Systems Troubleshooting Modules, Cables, and Connections Environmental Reporting FeaturesFigure A-1 Cisco 3620 Router Front-Panel LEDs Reading Front-Panel LEDsFigure A-2 Cisco 3640 Router Front-Panel LEDs Color Power Supply Status Color DescriptionColor RPS Status LED Front-Panel LEDs on Cisco 3631 RoutersReading Rear-Panel LEDs Rear-Panel LEDs on Cisco 3631 RoutersColor Status System Rear-Panel LEDs on Cisco 3660 RoutersCisco 3600 Series Error Messages Error MessagesMessage LED Type LED Color Message Cisco 3660 Error MessagesFan Cage in Cisco 3660 Routers hardware configuration note Cisco 3600 Series Routers hardware configuration note PS1, PS2 Amber Recovering a Lost Password Entering ROM Monitor Mode Using the ROM MonitorEnter ROM Monitor Mode by Using the reload Command ROM Monitor CommandsROM Monitor Syntax Conventions Command abcROM Monitor Command Descriptions Router Management CommandsBoot Commands in the ROM Monitor Entering Boot Commands Other Useful ROM Monitor Commands Informational Commands in the ROM MonitorConfiguration Register Commands Debugging CommandsModifying the Configuration Register in Menu Mode Recovering Cisco IOS Software Images Description and Options of the xmodem CommandConsole Requirements Procedure for the xmodem Command Configuration Register Settings Configuration RegisterBit Number Hexadecimal Meaning Changing Configuration Register SettingsRouter# config-register 0xvalue Boot Field Meaning Configuring the Boot FieldBaud Bit Bit Address net hostRouter# configure Enabling Booting from Flash MemorySymbols IN-2 IN-3 IN-4 IN-5 IN-6