Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems DGS-1224T manual Web-based Utility, Login

Models: DGS-1224T

1 59

Download 59 pages 54.28 Kb

Page 29

Web-based Utility

Web-based Utility

The DGS-1224T Web-Smart Switch has a web browser GUI interface for configuring the Switch through a web browser. To see the list of web browsers the Web-based Utility supports, see Supported web browsers on page 20. A network administrator can manage, control and monitor the Switch from a PC on the local LAN. This section describes how to operate the functions found in the Web-based Utility.

Login

Before beginning to configure the Web-Smart Switch through a web browser over an Ethernet connection, the PC used to manage the Switch must reside on the same the IP network. By default, the Switch automatically obtains an IP address from a DHCP Server. The admin configuring the Switch must check the LAN’s DHCP Server to identify the IP Address assigned to the Switch. The default IP address is 192.168.0.1 if the Switch cannot successfully obtain an IP address from a DHCP Server. If the DHCP assigned IP address of the Web- Smart Switch is 192.168.0.1, then the managing PC should use 192.168.0.x (where x is a number between 2 and 254) as its IP address, with a subnet mask also being the same (255.255.255.0 if not assigned by a DHCP Server). To begin, open a supported web browser and enter the IP address of the Switch (ex http://192.168.0.1).

Figure 14 – Logging into the Switch’s (DHCP assigned) IP address

Alternatively, through the SmartConsole Utility, when the Switch is discovered, select the device shown in the Monitor List of the SmartConsole Utility to open the device in a web browser.

25

Image 29

Cisco Systems DGS-1224T manual Web-based Utility, Login

Contents

24-Port 10/100/1000Mbps Gigabit Ethernet Switch + 2-Port mini GBIC First EditionWeb-Smart Switch User’s Guide D-Link DGS-1224TTABLE OF CONTENTS SmartConsole Utility Features Installing the SmartConsole UtilityDevice Setting LoginMonitoring Statistics Security Mac Address Table Static MACSecurity Mac Address Table Dynamic Forwarding Table ABOUT THIS GUIDE PurposeTerms/Usage INTRODUCTION Gigabit Ethernet TechnologyFast Ethernet Technology IEEE 802.1Q VLAN Switching TechnologyFeatures Switching Capacity Technical SpecificationsForwarding Mode Key Components / PerformancePort Functions DimensionsCombo ports in the front panelPhysical & Environment Unpacking InstallationUNPACKING AND INSTALLATION Figure 1 - Attach the adhesive rubber pads to the bottom Rack MountingFigure 3 - Mount the Switch in the rack or chassis Connecting Network CableFigure 2 - Attach the mounting brackets to the Switch AC Power IDENTIFYING EXTERNAL COMPONENTS Front PanelReset button Rear PanelUNDERSTANDING LED INDICATORS Power and System LEDsBlinking Supported web browsers Installing the SmartConsole UtilityCONFIGURATION Menu Toolbar SmartConsole Utility FeaturesFile includes Monitor save, Monitor save as, Monitor load and Exit Exit To exit the SmartConsole Utility Option includes Refresh Time and Group Timer functionsView Log To show the event of the SmartConsole Utility and the device Clear Log To clear all log entriesMonitor List Definitions of the Discovery List featuresDiscovery List Figure 8 - View trap Definitions of the Monitor List functions and termsDevice Setting Figure 11 - Password Change This space has been intentionally reserved for notesFigure 10 - Configuration Setting Figure 13 - DHCP Refresh Figure 12 - Firmware UpgradeLogin Web-based UtilityFigure 16 - Device Status Figure 15 - Log in screenTool Menu Figure 20 - Tool Menu Firmware Backup and Upload Figure 19 - Tool Menu Configure Backup and RestoreSystem Reboot Provides a safe way to reboot the system Setup MenuFigure 21 - Tool Menu System Reboot Setup MenuFigure 23 - System System Setting System System SettingSystem Trap Setting Fiber Port Events Monitors the fiber port status Figure 25 - System Port Setting System Port SettingSystem SNMP Setting Figure 26 - System SNMP Setting Figure 27 - System Password Access Control System Password Access ControlConfiguration 802.1Q VLAN Configuration Jumbo FrameFigure 30 - Configuration 802.1Q VLAN Add VID Figure 29 - Configuration 802.1Q VLAN Default SettingFigure 32 - Configuration 802.1Q VLAN VID Assignments Figure 31 - Configuration 802.1Q VLAN Example VIDsFigure 33 - Configuration Trunking Configuration TrunkingConfiguration IGMP Snooping Figure 34 - Configuration IGMP Snooping Configuration Robustness Variable 1-255 sec The Robustness Variable allows adjustment for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. The Robustness Variable can not be set zero, and SHOULD NOT be one. Default is 2 seconds Figure 35 - Configuration IGMP Router port Settings Figure 36 - Configuration IGMP Multicast Entry Table Figure 37 - Configuration Spanning Tree Configuration 802.1D Spanning TreeRoot Bridge Displays the MAC address of the Root Bridge Bridge Priority This value between 0 and 65535 specifies theRoot port Displays the root port Root Path Cost Shows the root path costConfiguration Port Mirroring Security Safeguard Engine QoS 802.1p Default PrioritySecurity Broadcast Storm Control Figure 40 - Security Safeguard EngineFigure 41 - Security Broadcast Storm Control Security 802.1X SettingKey Masked password matching the Radius Server Key Page Figure 43 - Security Static Mac Address Security Mac Address Table Static MACFigure 44 - Security Dynamic Forwarding Table Security Mac Address Table Dynamic Forwarding TableMonitoring Statistics Figure 46 - Monitoring Port Statistics