Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems DGS-1224T manual Fiber Port Events Monitors the fiber port status

Models: DGS-1224T

1 59

Download 59 pages 54.28 Kb

Page 35

Fiber Port Events: Monitors the fiber port status.

Enabled, enter the Destination IP address of the managing PC that will receive trap information.

Figure 24 – System > Trap Setting

System Event: Monitors the system’s trapping information. Device Bootup: Traps system boot-up information.

Illegal Login: Traps events of incorrect password logins, recording the IP of the originating PC.

Fiber Port Events: Monitors the fiber port status.

Link Up/Link Down: Traps fiber connection information. Twisted pair Port Events: Monitors the copper cable port status.

Link Up/Link Down: Traps copper connection information.

31

Image 35

Cisco Systems DGS-1224T manual Fiber Port Events Monitors the fiber port status

Contents

D-Link DGS-1224T First Edition24-Port 10/100/1000Mbps Gigabit Ethernet Switch + 2-Port mini GBIC Web-Smart Switch User’s GuideTABLE OF CONTENTS Login Installing the SmartConsole UtilitySmartConsole Utility Features Device SettingMonitoring Statistics Security Mac Address Table Static MACSecurity Mac Address Table Dynamic Forwarding Table ABOUT THIS GUIDE PurposeTerms/Usage INTRODUCTION Gigabit Ethernet TechnologyFast Ethernet Technology IEEE 802.1Q VLAN Switching TechnologyFeatures Key Components / Performance Technical SpecificationsSwitching Capacity Forwarding Modefront panel DimensionsPort Functions Combo ports in thePhysical & Environment Unpacking InstallationUNPACKING AND INSTALLATION Figure 1 - Attach the adhesive rubber pads to the bottom Rack MountingFigure 3 - Mount the Switch in the rack or chassis Connecting Network CableFigure 2 - Attach the mounting brackets to the Switch AC Power IDENTIFYING EXTERNAL COMPONENTS Front PanelReset button Rear PanelUNDERSTANDING LED INDICATORS Power and System LEDsBlinking Supported web browsers Installing the SmartConsole UtilityCONFIGURATION Menu Toolbar SmartConsole Utility FeaturesFile includes Monitor save, Monitor save as, Monitor load and Exit Clear Log To clear all log entries Option includes Refresh Time and Group Timer functionsExit To exit the SmartConsole Utility View Log To show the event of the SmartConsole Utility and the deviceMonitor List Definitions of the Discovery List featuresDiscovery List Figure 8 - View trap Definitions of the Monitor List functions and termsDevice Setting Figure 11 - Password Change This space has been intentionally reserved for notesFigure 10 - Configuration Setting Figure 13 - DHCP Refresh Figure 12 - Firmware UpgradeLogin Web-based UtilityFigure 16 - Device Status Figure 15 - Log in screenTool Menu Figure 20 - Tool Menu Firmware Backup and Upload Figure 19 - Tool Menu Configure Backup and RestoreSetup Menu Setup MenuSystem Reboot Provides a safe way to reboot the system Figure 21 - Tool Menu System RebootFigure 23 - System System Setting System System SettingSystem Trap Setting Fiber Port Events Monitors the fiber port status Figure 25 - System Port Setting System Port SettingSystem SNMP Setting Figure 26 - System SNMP Setting Figure 27 - System Password Access Control System Password Access ControlConfiguration 802.1Q VLAN Configuration Jumbo FrameFigure 30 - Configuration 802.1Q VLAN Add VID Figure 29 - Configuration 802.1Q VLAN Default SettingFigure 32 - Configuration 802.1Q VLAN VID Assignments Figure 31 - Configuration 802.1Q VLAN Example VIDsFigure 33 - Configuration Trunking Configuration TrunkingConfiguration IGMP Snooping Figure 34 - Configuration IGMP Snooping Configuration Robustness Variable 1-255 sec The Robustness Variable allows adjustment for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. The Robustness Variable can not be set zero, and SHOULD NOT be one. Default is 2 seconds Figure 35 - Configuration IGMP Router port Settings Figure 36 - Configuration IGMP Multicast Entry Table Figure 37 - Configuration Spanning Tree Configuration 802.1D Spanning TreeRoot Path Cost Shows the root path cost Bridge Priority This value between 0 and 65535 specifies theRoot Bridge Displays the MAC address of the Root Bridge Root port Displays the root portConfiguration Port Mirroring Security Safeguard Engine QoS 802.1p Default PrioritySecurity Broadcast Storm Control Figure 40 - Security Safeguard EngineFigure 41 - Security Broadcast Storm Control Security 802.1X SettingKey Masked password matching the Radius Server Key Page Figure 43 - Security Static Mac Address Security Mac Address Table Static MACFigure 44 - Security Dynamic Forwarding Table Security Mac Address Table Dynamic Forwarding TableMonitoring Statistics Figure 46 - Monitoring Port Statistics