Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems DGS-1224T manual Rack Mounting, Attach the adhesive rubber pads to the bottom

Models: DGS-1224T

1 59

Download 59 pages 54.28 Kb

Page 14

Figure 1 – Attach the adhesive rubber pads to the bottom

•Install the Switch in a site free from strong electromagnetic field generators (such as motors), vibration, dust, and direct exposure to sunlight.

•Leave at least 10cm of space to the front and rear of the Switch for ventilation.

•Install the Switch on a sturdy, level surface that can support its weight, or in an EIA standard-size equipment rack. For information on rack installation, see the next section, Rack Mounting.

•When installing the Switch on a level surface, attach the rubber pads (feet) to the bottom. The rubber feet cushion the switch and helps protect the case from scratches.

Figure 1 – Attach the adhesive rubber pads to the bottom

Rack Mounting

The Switch can be mounted in an EIA standard-size, 19-inch rack or chassis, which can be located in a wiring closet with other equipment. Attach the mounting brackets to the Switch’s side panels (one on each side), and secure them with the provided screws.

10

Image 14

Cisco Systems DGS-1224T manual Rack Mounting, Attach the adhesive rubber pads to the bottom

Contents

Web-Smart Switch User’s Guide First Edition24-Port 10/100/1000Mbps Gigabit Ethernet Switch + 2-Port mini GBIC D-Link DGS-1224TTABLE OF CONTENTS Device Setting Installing the SmartConsole UtilitySmartConsole Utility Features LoginMonitoring Statistics Security Mac Address Table Static MACSecurity Mac Address Table Dynamic Forwarding Table ABOUT THIS GUIDE PurposeTerms/Usage Gigabit Ethernet Technology INTRODUCTIONFast Ethernet Technology Switching Technology IEEE 802.1Q VLANFeatures Forwarding Mode Technical SpecificationsSwitching Capacity Key Components / PerformanceCombo ports in the DimensionsPort Functions front panelPhysical & Environment Unpacking InstallationUNPACKING AND INSTALLATION Rack Mounting Figure 1 - Attach the adhesive rubber pads to the bottomFigure 3 - Mount the Switch in the rack or chassis Connecting Network CableFigure 2 - Attach the mounting brackets to the Switch AC Power Front Panel IDENTIFYING EXTERNAL COMPONENTSRear Panel Reset buttonPower and System LEDs UNDERSTANDING LED INDICATORSBlinking Supported web browsers Installing the SmartConsole UtilityCONFIGURATION Menu Toolbar SmartConsole Utility FeaturesFile includes Monitor save, Monitor save as, Monitor load and Exit View Log To show the event of the SmartConsole Utility and the device Option includes Refresh Time and Group Timer functionsExit To exit the SmartConsole Utility Clear Log To clear all log entriesMonitor List Definitions of the Discovery List featuresDiscovery List Definitions of the Monitor List functions and terms Figure 8 - View trapDevice Setting Figure 11 - Password Change This space has been intentionally reserved for notesFigure 10 - Configuration Setting Figure 12 - Firmware Upgrade Figure 13 - DHCP RefreshWeb-based Utility LoginFigure 15 - Log in screen Figure 16 - Device StatusTool Menu Figure 19 - Tool Menu Configure Backup and Restore Figure 20 - Tool Menu Firmware Backup and UploadFigure 21 - Tool Menu System Reboot Setup MenuSystem Reboot Provides a safe way to reboot the system Setup MenuFigure 23 - System System Setting System System SettingSystem Trap Setting Fiber Port Events Monitors the fiber port status System Port Setting Figure 25 - System Port SettingSystem SNMP Setting Figure 26 - System SNMP Setting System Password Access Control Figure 27 - System Password Access ControlConfiguration Jumbo Frame Configuration 802.1Q VLANFigure 29 - Configuration 802.1Q VLAN Default Setting Figure 30 - Configuration 802.1Q VLAN Add VIDFigure 31 - Configuration 802.1Q VLAN Example VIDs Figure 32 - Configuration 802.1Q VLAN VID AssignmentsFigure 33 - Configuration Trunking Configuration TrunkingConfiguration IGMP Snooping Figure 34 - Configuration IGMP Snooping Configuration Robustness Variable 1-255 sec The Robustness Variable allows adjustment for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. The Robustness Variable can not be set zero, and SHOULD NOT be one. Default is 2 seconds Figure 35 - Configuration IGMP Router port Settings Figure 36 - Configuration IGMP Multicast Entry Table Configuration 802.1D Spanning Tree Figure 37 - Configuration Spanning TreeRoot port Displays the root port Bridge Priority This value between 0 and 65535 specifies theRoot Bridge Displays the MAC address of the Root Bridge Root Path Cost Shows the root path costConfiguration Port Mirroring QoS 802.1p Default Priority Security Safeguard EngineFigure 40 - Security Safeguard Engine Security Broadcast Storm ControlSecurity 802.1X Setting Figure 41 - Security Broadcast Storm ControlKey Masked password matching the Radius Server Key Page Security Mac Address Table Static MAC Figure 43 - Security Static Mac AddressSecurity Mac Address Table Dynamic Forwarding Table Figure 44 - Security Dynamic Forwarding TableMonitoring Statistics Figure 46 - Monitoring Port Statistics