USB Communication Settings | Code Alarm CR3 manual

1.6.2.1 - USB Communication Settings

USB Keyboard Mode - Data is sent from the Reader and interpreted by the host just as if a US keyboard was being used to enter data.

USB Downloader - This mode is the standard way of transferring batch ﬁ les or new ﬁ rmware through the USB port.

USB Native Two Way Mode - This mode is utilized when there is a need for error-corrected communica- tion between the CR3 and an application through the USB port.

USB Virtual COM 1 Way Mode - This mode allows a USB-cabled CR3 to function as a virtual COM port. To use the CR3 in this mode, download the driver at www.codecorp.com/downloads/codexmltools.htm.

Scan the following codes to set the appropriate USB communication setting:

USB Keyboard

USB Downloader

USB Native Two Way Mode

USB Virtual COM 1 Way Mode

You must ﬁ rst install the virtual com port driver before utilizing this mode.

Reset to USB Factory Defaults

Bluetooth settings will not be erased.

Save Settings

C002332_09_CR3 User Manual - 9

Image 15

Code Alarm CR3 manual USB Communication Settings, USB Keyboard USB Downloader, USB Virtual COM 1 Way Mode

Contents

Manual Version Laser/LED Radiation Statement of Agency Compliance Save Settings Table of Contents Reader Feedback and Special Settings CR3 Programming Symbology Settings Adding a Preﬁx or Sufﬁx and Reader Text Commands CR3 Maintenance and TroubleshootingAdvanced Decode Performance Getting Started Introduction Unpacking Powering On/Off Reader Description of Button Function Keypad/Icon Overview Icon Description Power Icons RS232 Batch Cable-Detect Default Batch OperationIntroduction RS232 Considerations Introduction Cabled Operation USB Keyboard Mode USB Cable Installation Guide USB Keyboard USB Downloader USB Communication SettingsUSB Virtual COM 1 Way Mode Reset to USB Factory Defaults PS2 Cable Installation Guide PS2 Communication SettingsPS2 Mode Save Settings Stop Bits Data Bits Parity None RS232 Cable Installation GuideMode RS232 One Way Mode Baud Rate RS232 Communication Parity Settings RS232 Communication Data Bit SettingsRS232 Communication Stop Bit Settings RS232 Communication Baud Rate Settings Cabled 2 hours Cabled Always Default Cabled Reader Time Out Settings Example Reset to RF Factory Defaults QuickConnect Bluetooth Radio Operation RF Two Way Mode RF One Way Mode Max Range Bluetooth Radio Auto Connect Bluetooth DisconnectBluetooth Radio Auto Connect On Default Bluetooth Radio Auto Disconnect Bluetooth Radio Time Out Settings Uncabled OperationsBluetooth Radio Out of Range Notiﬁcation Settings Bluetooth Radio Reader Feedback GuideRS232 Targeting and Reading Techniques To read a symbol with the CR3 Imager Field of View and Resolution Decode Zone BH1 or BH2 Battery Handle Attaching HandlesH1 Handle Attaching and Detaching the Lithium Ion Battery Reader Battery Installation Optimization and Trigger Programming DOT Introduction Global Trigger Optimization Matrix Read with Near-Field Imager only Read Codes with Both Imagers DefaultLeft Trigger Optimization Matrix Left Trigger Programming Right Trigger Optimization Matrix Right Trigger ProgrammingRead Code with Near-Field Imager only Handle Trigger Programming Handle Optimization Matrix Both Near & Far Field On Far Field Only On Off DefaultContinuous Trigger Optimization Continuous Scan Continuous Scan Sleep Time Out Continuous Scan SettingsMotion Detection Scan Settings Continuous Scan Trigger Delays CR3 Programming Symbology Settings Codabar Symbology Aztec Symbology Codablock F On Codablock F Off Default Codablock F SymbologyCode 11 Symbology Code 39 Symbology Sample Trioptic Code Code 93 SymbologyCode 128 Symbology Code 93 On Default Code 93 Off Composite Symbologies Data Matrix SymbologyGoCode Symbology Maxicode Symbology Interleaved 2 of 5 Symbology Matrix 2 of 5 Symbology MSI Plessy SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 On NEC 2 of 5 Off Default NEC 2 of 5 Symbology Australian Post On Japan Post On Postal SymbologiesRoyal Mail On Disable All Postal Codes Default Pharmacode RSS Symbology QR Code Symbology UPC/EAN/JAN Telepen Symbology Reader Feedback and Special Settings Vibrate On / Beep On Vibrate On / Beep Off Volume and Vibration SettingsOff Default Low Medium Code Readability Index Backlight Intensity Settings Readability Index Output DisableLow Med Default High Backlight Timeout Settings Laser SettingsReader Power Off Settings Reader ID and Firmware Reader Settings LockReader Settings Locked Reader ID and Firmware Version No Leading French German Time Stamp SettingsUS English Default US English Leading Keyboard Support Reader ID Firmware Version Lockout Link Mode Lock-out Link Mode Advanced Decode Performance Set Targeting Zone Tolerances DefaultEnable Continuous Illumination Continuous Illumination Windowing Large 2-Dimensional Codes 640 x 640 pixels Mirror Decoding VGA & Megapixel SettingsCodes Enable Sxga 1280 x Enable VGA 640 x Adding a Preﬁx or Sufﬁx and Reader Text Commands Preﬁx Settings Sufﬁx SettingsPreﬁx Comma Preﬁx Space Erase Preﬁx & Sufﬁx Data Erase Preﬁx and Sufﬁx SettingsReader Text Commands Reader Text Commands On CR3 Maintenance and Troubleshooting General Safety Information Reset Reader to Factory Defaults Warranty Coverage and Procedure WarrantyLimited Warranty Terms of Warranty General CR3 Accessories Technical Support and Returns Frequently Asked QuestionsCR3 Maintenance Cleaning the CR3 Window