Codablock F Symbology, Code 11 Symbology | Code Alarm CR3 manual

3.4 - Codablock F Symbology

Scan the following codes to enable/disable Codablock F symbology settings:

Codablock F On

Codablock F Off (Default)

Sample Codablock F Code

Note: When Codablock F and Code 128 decoding are enabled, there is some danger of mistakenly decoding a damaged Codablock F symbol as a Code 128 symbol. Therefore, Code 128 decoding should be disabled when Codablock F decoding is enabled.

3.5 - Code 11 Symbology

Scan the following codes to enable/disable Code 11 symbology settings:

Code 11 On (Default)

Code 11 Off

Code 11 Checksum 1 digit

Code 11 Checksum 2 Digit & Stripped from Result

Code 11 Checksum 1 Digit & Stripped from Result

Code 11 Sample with 1 Checksum Digit

3.6 - Code 39 Symbology

Scan the following codes to enable/disable Code 39 symbology settings:

Code 39 On (Default)	Code 39 Off	Enable Checksum
Disable Checksum (Default)	Enable Checksum and Strip From Result
Code 39 Extended Full ASCII On	Code 39 Extended Full ASCII Off (Default)

Save Settings

C002332_09_CR3 User Manual - 34

Image 40

Code Alarm CR3 manual Codablock F Symbology, Code 11 Symbology, Code 39 Symbology, Codablock F On Codablock F Off Default

Contents

Manual Version Statement of Agency Compliance Laser/LED Radiation Save Settings Table of Contents CR3 Programming Symbology Settings Reader Feedback and Special Settings CR3 Maintenance and Troubleshooting Adding a Preﬁx or Sufﬁx and Reader Text CommandsAdvanced Decode Performance Getting Started Introduction Powering On/Off Reader Unpacking Keypad/Icon Overview Description of Button Function Power Icons Icon Description Batch Operation RS232 Batch Cable-Detect DefaultIntroduction RS232 Considerations Cabled Operation Introduction USB Cable Installation Guide USB Keyboard Mode USB Communication Settings USB Virtual COM 1 Way ModeReset to USB Factory Defaults USB Keyboard USB Downloader PS2 Communication Settings PS2 Cable Installation GuidePS2 Mode Save Settings RS232 Cable Installation Guide Mode RS232 One Way ModeBaud Rate Stop Bits Data Bits Parity None RS232 Communication Data Bit Settings RS232 Communication Stop Bit SettingsRS232 Communication Baud Rate Settings RS232 Communication Parity Settings Cabled Reader Time Out Settings Cabled 2 hours Cabled Always Default Bluetooth Radio Operation Example Reset to RF Factory Defaults QuickConnect RF One Way Mode Max Range RF Two Way Mode Bluetooth Disconnect Bluetooth Radio Auto ConnectBluetooth Radio Auto Connect On Default Bluetooth Radio Time Out Settings Uncabled Operations Bluetooth Radio Auto DisconnectBluetooth Radio Out of Range Notiﬁcation Settings Reader Feedback Guide Bluetooth RadioRS232 To read a symbol with the CR3 Targeting and Reading Techniques Imager Field of View and Resolution Decode Zone Attaching Handles BH1 or BH2 Battery HandleH1 Handle Reader Battery Installation Attaching and Detaching the Lithium Ion Battery Optimization and Trigger Programming Introduction DOT Global Trigger Optimization Matrix Read Codes with Both Imagers Default Left Trigger Optimization MatrixLeft Trigger Programming Read with Near-Field Imager only Right Trigger Programming Right Trigger Optimization MatrixRead Code with Near-Field Imager only Handle Optimization Matrix Handle Trigger Programming Far Field Only On Off Default Continuous Trigger OptimizationContinuous Scan Both Near & Far Field On Continuous Scan Settings Motion Detection Scan SettingsContinuous Scan Trigger Delays Continuous Scan Sleep Time Out CR3 Programming Symbology Settings Aztec Symbology Codabar Symbology Codablock F Symbology Code 11 SymbologyCode 39 Symbology Codablock F On Codablock F Off Default Code 93 Symbology Code 128 SymbologyCode 93 On Default Code 93 Off Sample Trioptic Code Data Matrix Symbology Composite SymbologiesGoCode Symbology Interleaved 2 of 5 Symbology Maxicode Symbology MSI Plessy Symbology Matrix 2 of 5 SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 Symbology NEC 2 of 5 On NEC 2 of 5 Off Default Postal Symbologies Royal Mail On Disable All Postal Codes DefaultPharmacode Australian Post On Japan Post On QR Code Symbology RSS Symbology Telepen Symbology UPC/EAN/JAN Reader Feedback and Special Settings Volume and Vibration Settings Off Default Low MediumCode Readability Index Vibrate On / Beep On Vibrate On / Beep Off Readability Index Output Disable Backlight Intensity SettingsLow Med Default High Laser Settings Backlight Timeout SettingsReader Power Off Settings Reader Settings Lock Reader Settings LockedReader ID and Firmware Version Reader ID and Firmware Time Stamp Settings US English Default US English LeadingKeyboard Support No Leading French German Lock-out Link Mode Reader ID Firmware Version Lockout Link Mode Advanced Decode Performance Default Enable Continuous IlluminationContinuous Illumination Set Targeting Zone Tolerances Windowing Large 2-Dimensional Codes 640 x 640 pixels VGA & Megapixel Settings Codes Enable Sxga 1280 xEnable VGA 640 x Mirror Decoding Adding a Preﬁx or Sufﬁx and Reader Text Commands Sufﬁx Settings Preﬁx SettingsPreﬁx Comma Preﬁx Space Erase Preﬁx and Sufﬁx Settings Reader Text CommandsReader Text Commands On Erase Preﬁx & Sufﬁx Data CR3 Maintenance and Troubleshooting Reset Reader to Factory Defaults General Safety Information Warranty Limited WarrantyTerms of Warranty Warranty Coverage and Procedure CR3 Accessories General Frequently Asked Questions CR3 MaintenanceCleaning the CR3 Window Technical Support and Returns