Continuous Trigger Optimization, Continuous Scan | Code Alarm CR3

2.9 - Continuous Trigger Optimization

DOT

2.10 - Continuous Scan

Scan the following codes to turn continuous scanning on/off:

Both Near & Far Field On

Near Field Only On

Far Field Only On

Off (Default)

Note: This function is only recommended for cabled or short term use if battery is the only power supply. See section 7.4.1 for Sleep Time Out Settings

Save Settings

C002332_09_CR3 User Manual - 30

Image 36

Code Alarm CR3 Continuous Trigger Optimization, Continuous Scan, Both Near & Far Field On, Far Field Only On Off Default

Contents

Manual Version Statement of Agency Compliance Laser/LED Radiation Save Settings Table of Contents CR3 Programming Symbology Settings Reader Feedback and Special Settings Adding a Preﬁx or Sufﬁx and Reader Text Commands CR3 Maintenance and TroubleshootingAdvanced Decode Performance Getting Started Introduction Powering On/Off Reader Unpacking Keypad/Icon Overview Description of Button Function Power Icons Icon Description RS232 Batch Cable-Detect Default Batch OperationIntroduction RS232 Considerations Cabled Operation Introduction USB Cable Installation Guide USB Keyboard Mode USB Communication Settings USB Virtual COM 1 Way ModeReset to USB Factory Defaults USB Keyboard USB Downloader PS2 Cable Installation Guide PS2 Communication SettingsPS2 Mode Save Settings RS232 Cable Installation Guide Mode RS232 One Way ModeBaud Rate Stop Bits Data Bits Parity None RS232 Communication Data Bit Settings RS232 Communication Stop Bit SettingsRS232 Communication Baud Rate Settings RS232 Communication Parity Settings Cabled Reader Time Out Settings Cabled 2 hours Cabled Always Default Bluetooth Radio Operation Example Reset to RF Factory Defaults QuickConnect RF One Way Mode Max Range RF Two Way Mode Bluetooth Radio Auto Connect Bluetooth DisconnectBluetooth Radio Auto Connect On Default Bluetooth Radio Auto Disconnect Bluetooth Radio Time Out Settings Uncabled OperationsBluetooth Radio Out of Range Notiﬁcation Settings Bluetooth Radio Reader Feedback GuideRS232 To read a symbol with the CR3 Targeting and Reading Techniques Imager Field of View and Resolution Decode Zone BH1 or BH2 Battery Handle Attaching HandlesH1 Handle Reader Battery Installation Attaching and Detaching the Lithium Ion Battery Optimization and Trigger Programming Introduction DOT Global Trigger Optimization Matrix Read Codes with Both Imagers Default Left Trigger Optimization MatrixLeft Trigger Programming Read with Near-Field Imager only Right Trigger Optimization Matrix Right Trigger ProgrammingRead Code with Near-Field Imager only Handle Optimization Matrix Handle Trigger Programming Far Field Only On Off Default Continuous Trigger OptimizationContinuous Scan Both Near & Far Field On Continuous Scan Settings Motion Detection Scan SettingsContinuous Scan Trigger Delays Continuous Scan Sleep Time Out CR3 Programming Symbology Settings Aztec Symbology Codabar Symbology Codablock F Symbology Code 11 SymbologyCode 39 Symbology Codablock F On Codablock F Off Default Code 93 Symbology Code 128 SymbologyCode 93 On Default Code 93 Off Sample Trioptic Code Composite Symbologies Data Matrix SymbologyGoCode Symbology Interleaved 2 of 5 Symbology Maxicode Symbology Matrix 2 of 5 Symbology MSI Plessy SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 Symbology NEC 2 of 5 On NEC 2 of 5 Off Default Postal Symbologies Royal Mail On Disable All Postal Codes DefaultPharmacode Australian Post On Japan Post On QR Code Symbology RSS Symbology Telepen Symbology UPC/EAN/JAN Reader Feedback and Special Settings Volume and Vibration Settings Off Default Low MediumCode Readability Index Vibrate On / Beep On Vibrate On / Beep Off Backlight Intensity Settings Readability Index Output DisableLow Med Default High Backlight Timeout Settings Laser SettingsReader Power Off Settings Reader Settings Lock Reader Settings LockedReader ID and Firmware Version Reader ID and Firmware Time Stamp Settings US English Default US English LeadingKeyboard Support No Leading French German Lock-out Link Mode Reader ID Firmware Version Lockout Link Mode Advanced Decode Performance Default Enable Continuous IlluminationContinuous Illumination Set Targeting Zone Tolerances Windowing Large 2-Dimensional Codes 640 x 640 pixels VGA & Megapixel Settings Codes Enable Sxga 1280 xEnable VGA 640 x Mirror Decoding Adding a Preﬁx or Sufﬁx and Reader Text Commands Preﬁx Settings Sufﬁx SettingsPreﬁx Comma Preﬁx Space Erase Preﬁx and Sufﬁx Settings Reader Text CommandsReader Text Commands On Erase Preﬁx & Sufﬁx Data CR3 Maintenance and Troubleshooting Reset Reader to Factory Defaults General Safety Information Warranty Limited WarrantyTerms of Warranty Warranty Coverage and Procedure CR3 Accessories General Frequently Asked Questions CR3 MaintenanceCleaning the CR3 Window Technical Support and Returns