Craftsman 917.28851 owner manual To Move Forward Backward, To Operate Mower

TO MOVE FORWARD AND

BACKWARD

The direction and speed of movement is controlled by the motion control lever. (J)

J

1.Start tractor with motion control lever in neutral position.

2.Release parking brake.

3.Slowly move motion control lever to desired position.

TO ADJUST MOWER CUTTING HEIGHT

TO ADJUST GAUGE WHEELS

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

1.Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in this section of manual).

2.With mower in desired height of cut posi- tion, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

3.Repeat for all, installing gauge wheel in same adjustment hole.

A

B

4.Realice el mismo procedimiento en el otro lado del tractor.

5.FIJE LAS PIEZAS DE PROPULSIÓN POS- TERIORES (C) – Levante la parte posterior de la cortadora, ubique la ranura de la pieza de unión (D) por encima de la clavija que hay en la barra posterior de la cortadora y fíjela con una arandela y un resorte de contención.

C

D

E

FJ

H

9.Retire el resorte de sujeción (K), deslice la abrazadera (L) hasta quitarla, y saque a presión la guía de la caja (P) hasta que se salga del soporte.

10.Instale la correa pasándola por encima de la polea del motor (M) y fijadors de la correa

(G).

M

The position of the attachment lift lever (A) determines the cutting height.

A

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil condi-

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attach- ment lift lever.

2.Start mower blades by engaging attach- ment clutch control.

TO STOP MOWER BLADES Disengage attachment clutch control.

6.FIJE LA PIEZA DE UNIÓN ANTERIOR (E)

– Trabaje por el lado izquierdo del tractor. Introduzca el extremo de la barra de la pieza de unión por el orificio anterior de la barra de suspensión anterior del tractor (F).

7.Introduzca el otro extremo de la pieza de unión (E) en el orificio que se encuentra en la barra anterior de la cortadora (H), y fíjelo por medio de una arandela y un resorte de contención (J).

8.Retire el resorte del cable del embrague (Q) del brazo del engranaje (R).

R

Q

IMPORTANTE: Verifique que la correa encaje bien en todas las ranuras de las poleas de la cortadora.

11.Suba la palanca elevadora a la posición de más arriba.

12.Si es necesario, ajuste las rueditas del calibre antes de poner en funcionamiento la corta- dora, como se ilustra en el capítulo de Manejo de este manual.

G MF

G

A E

tions, height of grass and types of grass being mowed.

•The average lawn should be cut to ap- proximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield

(S) in place.

S

B

P	C
K	D
L

12 53