OPERACIÓN
Estos símbolos pueden aparecer sobre su tractor o en la literatura proporcionada con el producto. Aprenda y comprenda sus significados.
.%542/ | !,4/ | "!*/ | %342!.'5 2«0)$/ | ,%.4/ |
|
| ||||||||
|
|
|
|
|
|
|
|
|
| ,!#)». |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ª |
|
|
|
ª |
|
|
|
| &2%./ª$% | |||||||||
|
|
| ||||||||||||
!0!'!$/ |
| 3%'!$/2! ª$%ª,!ª3%'!$/2! | ||||||||||||
|
|
|
|
|
|
|
|
| ||||||
|
|
| !42«3ª2/3 |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TO REMOVE WHEEL FOR REPAIRS
1.Block up axle securely.
2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).
3.Repair tire and reassemble.
NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.
4.Replace washers and snap retaining ring securely in axle groove.
5.Replace axle cover.
NOTE: To seal tire punctures and prevent flat tires due to slow leaks, purchase and use tire sealant from Sears. Tire sealant also prevents tire dry rot and corrosion.
NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.
After above adjustment is made, if the trac- tor still creeps forward or backward while motion control lever is in neutral position, follow these steps:
1.Loosen the adjustment bolt.
2.Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.
3.Tighten adjustment bolt securely.
4.Start engine and test.
5.If tractor still creeps, repeat above steps until satisfied.
TOSTARTENGINEWITHWEAKBATTERY
,5#%3 |
|
|
|
%.3%.$)$!3 | 0%$!,ª$%ª&2%./ªª | ||
!42«3 | (!#)!ª!$%,!.4% | #25#%2/ | |
|
| ª | ª |
|
|
|
Retaining
Axle Ring
Cover
Washers
WARNING:
!##%3/2)/ª$%,ª | !##%3/2)/ª$%,ª | 0%,)'2/ª'5!2$%ª,!3ª | 0%,)'2/3ª$% | |
%.'!.#(!$/ | $%3%.'!.#(!$/ |
| !2%!ª$%30%*!$!ª | 0%.$)%.4%3 |
|
|
| 6EAªLAªSECCIØNªDEªLASªREGLASªDEªSEGURIDAD ª | |
|
| 0%,)'2/ªINDICAªUNªPELIGROªQUEªSIªNOªSEªEVITAª | ||
|
| PROVOCAªMUERTEªOªLESIONESªGRAVESª | ||
|
| !$6%24%.#)!ªINDICAªUNªPELIGROªQUEªSIªNOªSEªEVITAª | ||
|
| PUEDEªPROVOCARªMUERTEªOªLESIONESªGRAVESª | ||
25%$!ª,)"2%ª | 02%#!5#)».ªINDICAªUNªPELIGROªQUEªSIªNOªSEªEVITAª | |||
3OLAMENTEªPARAªLOSª | PUEDEªPROVOCARªLESIONESªLIGERASªOªMODERADASª | |||
MODELOSªAUTOMATICO |
02%#!5#)».ªCUANDOªSEªUTILIZAªSINªELªSÓMBOLOªDEªAVISOª INDICAªUNAªSITUACIØNªQUEªPUEDEªPROVOCARªDA×OSªALª
TRACTORªYOªALªMOTORª
Square |
|
Key | 00 |
| 663 |
(Rear Wheel Only) |
|
FRONT WHEEL TOE-IN/CAMBER
Your new tractor front wheel
If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE section of this manual).
If “jumper cables” are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.
TO ATTACH JUMPER CABLES -
1. Connect one end of the RED cable to the |
POSITIVE (+) terminal of each battery(A- |
B), taking care not to short against tractor |
.OªSEGUIRªLASªSIGUIENTESªINSTRUCCIONESª PUEDEªPROVOCARªHERIDASªOªMUERTEª,OSª SÓMBOLOSªDEªAVISOªDEªSEGURIDADSEªUTILIZANª PARAªIDENTIFICARªINFORMACIONESªDEªSEGURIDADª RELATIVASªAªPELIGROSªQUEªPUEDENPROVOCARªLAª MUERTEªHERIDASªGRAVESªYOªDA×OSªAªLAª
MÈQUINA
350%2&)#)%3ª#!,)%.4%3ªINDICAªUNªPELIGROªQUEª SIªNOªSEªEVITAªPUEDEªPROVOCARªLAªMUERTEªLESIONESª
GRAVESªYOªDANOSªAªLAªMÈQUINAª
&5%'/ªINDICAªUNªPELIGROªQUEªSIªNOªSEªEVITAªPUEDEª
PROVOCARªLAªMUERTEªLESIONESªGRAVESªYOªDANOSª AªLAªMÈQUINAª
TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT
Themotioncontrolleverhasbeenpresetatthe factory; adjustment should not be necessary.
1.Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.
2.Start engine and move motion control lever until tractor does not move forward or backward.
3.Hold motion control lever in that position and turn engine off.
4.While holding motion control lever in place, loosen the adjustment bolt.
5.Move motion control lever to the neutral (lock gate) position.
6.Tighten adjustment bolt securely.
Motion Control | Neutral |
Lever | Lock |
| Gate |
| chassis. |
2. | Connect one end of the BLACK cable |
| to the NEGATIVE |
| charged battery. |
3. | Connect the other end of the BLACK |
| cable (D) to good chassis ground, away |
| from fuel tank and battery. |
TO REMOVE CABLES, REVERSE ORDER -
1.BLACK cable first from chassis and then from the fully charged battery.
2.RED cable last from both batteries.
Weak or | Fully |
Dead | Charged |
Battery | Battery |
02239 | Adjustment Bolt |
40 | 25 |