Package Diagrams | Cypress CY7C1470BV25, CY7C1474BV25, CY7C1472BV25

CY7C1470BV25

CY7C1472BV25, CY7C1474BV25

Package Diagrams

Figure 9. 100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm), 51-85050

16.00±0.20

14.00±0.10

100

81

1

22.00±0.20

20.00±0.10

30

31

50

80

0.30±0.08

0.65

TYP.

51

12° ±1° (8X)

1.40±0.05

SEE DETAIL

A

0.20 MAX.

1.60 MAX.

R 0.08 MIN. 0.20 MAX.

0.25

0° MIN.

STAND-OFF 0.05 MIN. 0.15 MAX.

SEATING PLANE

NOTE:

0.10

GAUGE PLANE

0° -7°

0.60±0.15

1.00 REF.

R 0.08 MIN. 0.20 MAX.

0.20 MIN.

DETAIL A

1.JEDEC STD REF MS-026

2.BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH

3.DIMENSIONS IN MILLIMETERS

51-85050-*B

Document #: 001-15032 Rev. *D

Page 26 of 29

[+] Feedback

Image 26

Cypress CY7C1470BV25, CY7C1474BV25, CY7C1472BV25 manual Package Diagrams, Pin Thin Plastic Quad Flatpack 14 x 20 x 1.4 mm

Contents

Selection Guide FeaturesFunctional Description Description 250 MHz 200 MHz 167 MHz Unit Logic Block Diagram CY7C1470BV25 2M x Logic Block Diagram CY7C1472BV25 4M x Logic Block Diagram CY7C1474BV25 1M x ADV/LD Pin Configurations Pin Tqfp Pinout TDI TDO CENNC/1G CE2 CLK Mode Ball Fbga 14 x 22 x 1.76 mm Pinout CY7C1474BV25 1M × Dqpx Pin Definitions Pin Name IO Type Pin DescriptionADV/LD TDI Functional Overview Parameter Description Test Conditions Min Max Unit ZZ Mode Electrical CharacteristicsBurst Write Accesses Used Truth TableAddress Operation Function CY7C1472BV25 Partial Write Cycle DescriptionFunction CY7C1470BV25 Function CY7C1474BV25 TAP Controller State Diagram Ieee 1149.1 Serial Boundary Scan Jtag TAP Instruction Set TAP Timing Hold Times TAP AC Switching CharacteristicsParameter Description Min Max Unit Clock GND ≤ VI ≤ Vddq TAP DC Electrical Characteristics And Operating Conditions5V TAP AC Test Conditions Scan Register Sizes Register Name Bit Size Identification Codes Instruction Description Boundary Scan Exit Order 2M x Bit # Ball ID Bit # Ball ID Boundary Scan Exit Order 4M xBoundary Scan Exit Order 1M x 10 R1 11 R2 12 R3 13 P2 Operating Range Electrical CharacteristicsMaximum Ratings Range Ambient AC Test Loads and Waveforms CapacitanceThermal Resistance Parameter Description Test Conditions Tqfp Fbga Unit Parameter Description 250 200 167 Unit Min Max Switching CharacteristicsSetup Times Output Times Data Switching WaveformsADV/LD Address A3 A4 NOP, Stall and Deselect Cycles Ordering Information 250 Package Diagrams Pin Thin Plastic Quad Flatpack 14 x 20 x 1.4 mm Ball Fbga 15 x 17 x 1.4 mm Ball Fbga 14 x 22 x 1.76 mm ECN No Issue Date Orig. of Change Description of Change Document History