Initial Configuration | Datacom Systems VS-1200 manual

Initial Configuration

35

Step 8. You are now connected at the Enter Username: prompt. Usernames and passwords are case-sensitive. Type Administrator (default value) and press the Enter key. At the Enter Password: prompt, type admin (default value) and press the Enter key to display the command line > prompt. At the command line > prompt, type su and press the Enter key. At the Enter Password: prompt, type password (default value) and press the Enter key to display the command line # prompt. To see a list of available commands, at either the > or # command line prompt, type ? and press the Enter key .

Step 9. SET IP (SE IP) by typing se ip xxx.xxx.xxx.xxx corresponding to a valid IP address for your network. Press the Enter key to continue.

Step 10. SET SUBNET (SE SU) by typing se su xxx.xxx.xxx.xxx corresponding to your network's subnet mask. Press the Enter key to continue.

Step 11. SET GATEWAY (SE GA) (if needed) by typing se ga xxx.xxx.xxx.xxx corresponding to your network's default gateway. Press the Enter key to continue.

Step 12. SHOW (SH) by typing sh and press the Enter key to display and affirm that the pending IP Address, IP Subnet and IP Default Gateway match the intended Local Area Network input IP Address, IP Subnet and IP Default Gateway.

© 2009 Datacom Systems Inc

Image 35

Datacom Systems VS-1200 manual Initial Configuration

Contents

USERguide Page Product Description Datacom Systems Inc VS-1200 Data Acccess Switch Table of Contents VS-1200 Series Functional Drawing Application Hardware InstallationCustomer Service Certifications and Marks Terms of UseCopyright License Agreement Trademark Attribution Proprietary Notice Safety Notices and Warnings VS-1200 Series Summary Overview What Shipped? VS-1200 Series Features and Benefits Operating Range Relative Humidity 5 to 90% non-condensing VS-1200 Series Common SpecificationsVS-1200 Series Model Specific Specifications Power Consumption 12W BTU/hPage VS-1210BT/SFP HardwareVS-1200 Series Front Panels Any-to-Any Ports PowerFront Panel Description Management Port Rear Panel Description Rear Label BT series Power Switch SFP seriesInput Power Serial DB9 Basic Functionality Initial ConfigurationCommand Line Interface CLI Basic Commands Read Only Access Password Recovery SET Port Monitor SE PO MO TAP Show Groups SH GR Group Name Show Port Routing SH PO RO Show Users SH US Superuser Commands Configuration AccessSU SET Password SU SE PA SET Date Mmddyy # SET IP Subnet Gateway # SE PO MO 3 OFF SET Time Hhmmss ADD User AD US HyperTerminal Serial Port Configuration DB9Delete User Username Port Number Management Port Configuration RJ45TCP/IP Winsock Telnet IP Address ConfigurationIP Address Configuration with HyperTerminal Accessories Communications HyperTerminal VS-1200 Data Acccess Switch Initial Configuration IP Address Configuration with Telnet Network Connections Accessories Command Prompt Initial Configuration Exercise CLI Setting Ports Initial Configuration # SET Port Monitor 2 from 8,9 # SET Port Monitor 1 from 7,9 # SET Port Monitor 8 from # SET Port Monitor 5 from# SET Port Monitor 6 from 3,4 # SET Port Monitor 7 from Intallation Prerequisites Safety GuidelinesSmall Form-Factor Plug Module Removing the SFP Module Installing the SFP ModulePage Any-to-Any Connection Hardware InstallationPower Management Connection VS-1210BT-BT/SFP VS-1200 Series Functional Drawing VS-1204BT VS-1204SFP Application Gathering the Data HyperTerminal configuration example VS-1200 Data Acccess Switch # SET Port Monitor 9 from # SET Port Monitor 4 from# SET Port Monitor 6 from VS-1200 Data Acccess Switch Application # SET Port Monitor 8 from 2,4 # SET Port Monitor 5 from 1,3# SET Port Monitor 6 from 1,3 # SET Port Monitor 7 from 2,4 Limits of Liability Customer ServiceInternet Warranty Datacom Systems Inc