# SET Port Monitor 1 from 7,9 | Datacom Systems VS-1200 specs

38

VS-1200 Data Acccess Switch

Then enter Superuser mode, at the user prompt >, enter SU, Enter key, and enter the Password (default: password) and Enter key. Default prompt is the # symbol.

In Superuser mode use the following syntax for the different connections. This syntax sets the input/ output for Any-to-Any ports as well as the input/output for Tap ports.

The VS-1200 Series factory default for all Any-to-Any ports is off.

Ensure there are no previous settings present, go through Ports 1-10 and set them to OFF as shown:

#SET PORT MONITOR 1 OFF

#SET PORT MONITOR 2 OFF

#SET PORT MONITOR 3 OFF

#SET PORT MONITOR 4 OFF

#SET PORT MONITOR 5 OFF

#SET PORT MONITOR 6 OFF

#SET PORT MONITOR 7 OFF

#SET PORT MONITOR 8 OFF

#SET PORT MONITOR 9 OFF

#SET PORT MONITOR 10 OFF

Now you can begin setting the Tap and Monitor ports as to which port inputs the data and which ports aggregate and/or output the data.

Port 1 is set as output for Ports 7 and 9’s input which is set with this syntax:

# SET PORT MONITOR 1 FROM 7,9

Port 2 is set as output for Ports 8 and 9’s input which is set with this syntax:

# SET PORT MONITOR 2 FROM 8,9

© 2009 Datacom Systems Inc

Image 38

Datacom Systems VS-1200 manual # SET Port Monitor 1 from 7,9, # SET Port Monitor 2 from 8,9

Contents

USERguide Page Product Description VS-1200 Data Acccess Switch Datacom Systems Inc Table of Contents VS-1200 Series Functional Drawing Application Hardware InstallationCustomer Service Proprietary Notice Terms of UseCopyright License Agreement Trademark Attribution Certifications and Marks Safety Notices and Warnings Overview VS-1200 Series Summary VS-1200 Series Features and Benefits What Shipped? Power Consumption 12W BTU/h VS-1200 Series Common SpecificationsVS-1200 Series Model Specific Specifications Operating Range Relative Humidity 5 to 90% non-condensingPage VS-1210BT/SFP HardwareVS-1200 Series Front Panels Any-to-Any Ports PowerFront Panel Description Rear Panel Description Management Port Serial DB9 Power Switch SFP seriesInput Power Rear Label BT series Basic Functionality Initial ConfigurationCommand Line Interface CLI Password Recovery Basic Commands Read Only Access SET Port Monitor SE PO MO Show Groups SH GR Group Name TAP Show Port Routing SH PO RO Show Users SH US Superuser Commands Configuration AccessSU SET Password SU SE PA # SET IP Subnet Gateway SET Date Mmddyy SET Time Hhmmss # SE PO MO 3 OFF ADD User AD US HyperTerminal Serial Port Configuration DB9Delete User Username Port Number Management Port Configuration RJ45TCP/IP Winsock Telnet IP Address ConfigurationIP Address Configuration with HyperTerminal Accessories Communications HyperTerminal VS-1200 Data Acccess Switch Initial Configuration IP Address Configuration with Telnet Network Connections Accessories Command Prompt Initial Configuration Exercise CLI Setting Ports Initial Configuration # SET Port Monitor 1 from 7,9 # SET Port Monitor 2 from 8,9 # SET Port Monitor 7 from # SET Port Monitor 5 from# SET Port Monitor 6 from 3,4 # SET Port Monitor 8 from Intallation Prerequisites Safety GuidelinesSmall Form-Factor Plug Module Installing the SFP Module Removing the SFP ModulePage Any-to-Any Connection Hardware InstallationPower Management Connection VS-1200 Series Functional Drawing VS-1210BT-BT/SFP VS-1204BT VS-1204SFP Gathering the Data HyperTerminal configuration example Application VS-1200 Data Acccess Switch # SET Port Monitor 9 from # SET Port Monitor 4 from# SET Port Monitor 6 from VS-1200 Data Acccess Switch Application # SET Port Monitor 7 from 2,4 # SET Port Monitor 5 from 1,3# SET Port Monitor 6 from 1,3 # SET Port Monitor 8 from 2,4 Limits of Liability Customer ServiceInternet Warranty Datacom Systems Inc