VS-1200 Data Acccess Switch | Datacom Systems specs

48

VS-1200 Data Acccess Switch

SOLUTION: The VS-1210BT/SFP solves all goals by accepting the input from the two SPAN ports along with the output from the TAP, aggregating and replicating the traffic to multiple ports and ports 9 and 10 provide small form pluggables that allow either fiber or copper connectivity.

CONFIGURATION: The IP address (default 192.168.1.1), Subnet Mask and Default Gateway is set during the 'Initial Configuration' for your Local Area Network settings and will not be covered in this section, see the 'IP Address Configuration with HyperTerminal 28 ' section for those steps. Use the syntax below in the Command Line Interface (CLI) to setup Tap and Any-to-Any ports (syntax is shown with either user > or Superuser # prompts):

For configuration, open HyperTerminal on your Management PC using the VS-1210BT/SFP SERIAL DB9 port. Settings are found in the 'Initial Configuration', 'SERIAL Port Configuration (DB9)', 'HyperTerminal 26 ' section.

Press twice Enter key and Enter key. Enter Username (default: Administrator) and Enter key.

Enter Password (default: admin) and Enter key. Default prompt is the > symbol. Enter superuser

mode, type su and Enter key. Enter Password (default: password) and Enter key. Default prompt is the # symbol. Use the following syntax to set the input/output for Any-to-Any ports as well as the output for Tap ports.

The VS-1200 Series factory default for all Any-to-Any ports is off.

Ensure there are no previous settings present, go through Ports 1-10 and set them to OFF as shown:

#SET PORT MONITOR 1 OFF

#SET PORT MONITOR 2 OFF

#SET PORT MONITOR 3 OFF

#SET PORT MONITOR 4 OFF

#SET PORT MONITOR 5 OFF

#SET PORT MONITOR 6 OFF

#SET PORT MONITOR 7 OFF

#SET PORT MONITOR 8 OFF

#SET PORT MONITOR 9 OFF

#SET PORT MONITOR 10 OFF

© 2009 Datacom Systems Inc

Image 48

Datacom Systems manual VS-1200 Data Acccess Switch

Contents

USERguide Page Product Description VS-1200 Data Acccess Switch Datacom Systems Inc Table of Contents Hardware Installation Customer ServiceVS-1200 Series Functional Drawing Application Terms of Use Copyright License Agreement Trademark AttributionProprietary Notice Certifications and Marks Safety Notices and Warnings Overview VS-1200 Series Summary VS-1200 Series Features and Benefits What Shipped? VS-1200 Series Common Specifications VS-1200 Series Model Specific SpecificationsPower Consumption 12W BTU/h Operating Range Relative Humidity 5 to 90% non-condensingPage Hardware VS-1200 Series Front PanelsVS-1210BT/SFP Power Front Panel DescriptionAny-to-Any Ports Rear Panel Description Management Port Power Switch SFP series Input PowerSerial DB9 Rear Label BT series Initial Configuration Command Line Interface CLIBasic Functionality Password Recovery Basic Commands Read Only Access SET Port Monitor SE PO MO Show Groups SH GR Group Name TAP Show Port Routing SH PO RO Superuser Commands Configuration Access SU SET Password SU SE PAShow Users SH US # SET IP Subnet Gateway SET Date Mmddyy SET Time Hhmmss # SE PO MO 3 OFF ADD User AD US Serial Port Configuration DB9 Delete User UsernameHyperTerminal Management Port Configuration RJ45 TCP/IP WinsockPort Number IP Address Configuration IP Address Configuration with HyperTerminalTelnet Accessories Communications HyperTerminal VS-1200 Data Acccess Switch Initial Configuration IP Address Configuration with Telnet Network Connections Accessories Command Prompt Initial Configuration Exercise CLI Setting Ports Initial Configuration # SET Port Monitor 1 from 7,9 # SET Port Monitor 2 from 8,9 # SET Port Monitor 5 from # SET Port Monitor 6 from 3,4# SET Port Monitor 7 from # SET Port Monitor 8 from Safety Guidelines Small Form-Factor Plug ModuleIntallation Prerequisites Installing the SFP Module Removing the SFP ModulePage Hardware Installation PowerAny-to-Any Connection Management Connection VS-1200 Series Functional Drawing VS-1210BT-BT/SFP VS-1204BT VS-1204SFP Gathering the Data HyperTerminal configuration example Application VS-1200 Data Acccess Switch # SET Port Monitor 4 from # SET Port Monitor 6 from# SET Port Monitor 9 from VS-1200 Data Acccess Switch Application # SET Port Monitor 5 from 1,3 # SET Port Monitor 6 from 1,3# SET Port Monitor 7 from 2,4 # SET Port Monitor 8 from 2,4 Customer Service Internet WarrantyLimits of Liability Datacom Systems Inc