Datalogic Scanning 1000I RS-232 Invert, Beep on ASCII BEL

Interface Features

Product Reference Guide

3-17

RS-232 Invert

Enables/disables inversion of RS-232 TXD and RXD signals.

Beep on ASCII BEL

Enables/disables ability of scanner to beep (sound a good read tone) on receiving an ASCII BEL

(07 hex).

START / END

PROGRAMMING BARCODES

Disable RS-232 Invert

DEFAULT

Enable RS-232 Invert

START / END

PROGRAMMING BARCODES

Enable Beep on ASCII BEL

DEFAULT

Disable Beep on ASCII BEL

Contents

Main Page i-i Table of Contents i-ii Magellan 1000i Product Reference Guide i-iii i-iv Magellan 1000i Chapter 1 Getting Started About This Manual Manual Conventions 1-2 Magellan 1000i Connecting the Scanner NOTE USB Connection RS-232 Serial Connection Figure 1 Programming Using the Programming Barcodes Resetting the Standard Product Defaults LED and Beeper Indicators Error Codes Page Chapter 2 General Features Double Read Timeout Double Read Timeout cont. Label Gone Timeout Productivity Index Reporting (PIR) Sleep Mode Sleep Mode cont. LED and Beeper Indicators Power On Al ert Good Read: When to Indicate Good Read Beep Control This feature enables/disables the scanners ability to beep upon a successful decode of a barcode. Good Read Beep Frequency Good Read Beep Length Specifies the duration of a good read beep. Good Read Beep Volume Scanning Features Targeted Scanning Mode Targ et M ode Act ive Time Target Mode Linger Time Wake Up Intensity Wake Up Intensity cont. Chapter 3 Interface Related Features Page Interface Selection Page Page Page Interface Features Obey/Ignore Host Commands Interface Features cont. Host Transmission Buffers RS-232 Interface Features Page Hardware Flow Control Intercharacter Delay Intercharacter Delay cont. Software Flow Control Disables/Enables software control using XON/XOFF characters. Host Echo Host Echo Quiet Interval Host Echo Quiet Interval cont. Signal Voltage: Normal/TTL Specifies whether the RS-232 interface provides TTL levels on the output pins TxD and RTS. RS-232 Invert Beep on ASCII BEL Beep on Not on File ACK NAK O ptions RS-232 Interface Features cont. cont. ACK Character NAK Character Retry on ACK NAK Timeout ACK NAK Tim eout Valu e ACK NAK R etry Cou nt ACK NAK Error Handling Transmission Failure Indication USB-OEM Interface Features USB-OEM Device usage IBM IBM Transmit Labels in Code 39 Format Wand E mula tion Supported Symbologies Wand Emulation Barcode Format Bar/Space Polarity Wand I dle St ate Signal Speed Transmit Trailing Noise Transmit Leading Noise Symbology Conversion Keyboard Wedg e USB Keyboard Page Caps Lock State Specifies the format in which the scanner sends character data. Page Page Page USB COM Interface Set-up Chapter 4 Data Editing OR... Data Editing Overview Please Keep In Mind... Global Prefix/Suffix OR... Global Prefix/Suffix cont. AIM ID Label ID Page Page Page Page Page Page Case Conversion Character Conversion Page Chapter 5 Symbologies UPC-A Disable/Enable UPC-A Enable this option to transmit the check digit along with UPC-A barcode data. Expand UPC-A to EAN-13 Number System Transmission This feature enables/disables transmission of UPC-A System Number. UPC-A Minimum Reads UPC-A In-store Minimum Reads UPC-E Disable/Enable UPC-E UPC-E continued Number System Digit Expand to UPC-E to UPC-A UPC-E continued Expand UPC-E to EAN13 Page EAN-13 Disable/Enable EAN-13 EAN-13 continued EAN-13 Flag 1 Character ISBN EAN-13 continued EAN-8 The following options apply to the EAN-8 symbology. Enable this option to transmit the check Digit along with EAN-8 barcode data. Disable/Enable EAN-8 When disabled, the scanner will not read EAN-8 barcodes. EAN-8 continued Enable EAN Two-Label Enables/disables the ability of the scanner to decode EAN two-label pairs. Add-ons Contact Customer Support for advanced programming of optional and conditional add-ons. Add-ons continued GS1 DataBar Omnidirectional / Stacked Omnidirectional Disable/Enable GS1 DataBar Omnidirectional UCC/EAN 128 Emulation GS1 DataBar Omnidirectional / Stacked Omnidirectional continued GS1 DataBar Expanded / Expanded Stacked Disable/Enable GS1 DataBar Expanded GS1-128 Emulation Page GS1 DataBar Expanded Length 1, Length 2 Programming Instructions Page Coupon Rea d Control This feature controls coupon reading. GS1 DataBar Limited The following options apply to the GS1 DataBar Limited symbology. Disable/Enable GS1 DataBar Limited When this feature is disabled, the scanner will not read GS1 DataBar Limited barcodes. GS1-128 Emulation GS1 DataBar Limited continued Code 39 Disable/Enable Code 39 Check Character Calculation Start/Stop Characters Enables/disables transmission of Code39 start and stop characters. Code 39 Full ASCII Enables/disables the translation of Code 39 characters to Code 39 full-ASCII characters. Code 39 continued Code 39 Length 1, Length 2 Programming Instructions Quiet Zones Code 39 continued Code 39 Stitching Pharmacode 39 The following options apply to the Pharmacode 39 symbology. Enables or disables transmission of Pharmacode 39 start/stop characters. Disable/Enable Pharmacode 39 When this feature is disabled, the scanner will not read Pharmacode 39 barcodes. Page Code 128 The following options apply to the Code 128 symbology. When this feature is disabled, the scanner will not read EAN 128 barcodes. Disable/Enable Code 128 When this feature is disabled, the scanner will not read Code 128 barcodes. Transmit Function Characters Page Code 128 Length 1, Length 2 Programming Instructions Code 128 Conve rsion to Code 39 Code 128 Stitching Interleaved 2 of 5 Disable/Enable Interleaved 2 of 5 Check Digit Calculation Enable this option to transmit the check digit with scanned barcode data. Page Interleaved 2 of 5 Length 1, Length 2 Programming Instructions Interleaved 2 of 5 Stitching Page Codabar Disable/Enable Codabar Check Character Verification Page Page Codabar Length 1, Length 2 Programming Instructions Quiet Zones Start/Stop Character Type Codabar has four pairs of Start/Stop patterns. Select one pair to match your application. The transmission of start and end characters of Codabar is selected below. Start/Stop Character Transmission Start/Stop Character Match Codabar Stitching Page Code 93 Disable/Enable Code 93 Page Code 93 Length 1, Length 2 Programming Instructions Code 93 Stitching MSI/Plessey The following options apply to the MSI/Plessey symbology. This feature specifies whether one or two check digits are to be calculated and verified. Disable/Enable MSI/Plessey When this feature is disabled, the scanner will not read MSI/Plessey barcodes. Number of Check Characters Page MSI/Plessey Leng th 1, Length 2 Programming Instructions MSI/Plessey Stitching Page Standard 2 of 5 The following options apply to the Standard 2 of 5 symbology. When enabled, the scanner will verify the check digit of the labels. Disable/Enable Standard 2 of 5 When this feature is disabled, the scanner will not read Standard 2 of 5 barcodes. When this option is enabled, the scanner will transmit the check digit. Page Standard 2 of 5 Length 1, Length 2 Programming Instructions Standard 2 of 5 Stitching Page Page Page 2D Symbologies PDF 417 Disable/Enable PDF 417 Length Control PDF 417 Length 1, Length 2 Programming Instructions Minimum Reads Datamatrix Disable/Enable Datamatrix When disabled, the scanner will not read Datamatrix barcodes. Length Control Datamatrix Length 1, Length 2 Programming Instructions Minimum Reads Image Capture How to Capture an Image Captured Image Format Chapter A Product Specifications Optical and Read Performance Parameters Scanner Dimensions Physical Properties Electrical Parameters Other Parameters Environmental Parameters Chapter B Cable Pinouts IBM Port 5B/9B/17 Standard Cable Pinouts (Primary Inter face Cables) RS-232 USB-OEM USB, USB Keyboard & USB COM Keyboard Wedg e Wand E mula tion Chapter C Alpha-Numeric Pad Alpha-Numeric Pad Appendix D Default Settings Defaults by Symbology The following is a partial list of key settings for each symbology type. Interface Default Exceptions IBM Interfaces Interface Default Exceptions continued RS-232 Wincor/Nixdorf Page Appendix E Keyboard Function Key Mappings Keyboard Model Cross Reference Page Page Page Page Page Chapter F Host Commands Accepting RS-232 Commands The scanner responds to the following RS-232 commands: Page Chapter G Sample Symbols Page ASCII Chart