Manuals / Dell / Computer Equipment / Switch

Dell 5324 manual Syntax Back-pressure No back-pressure Default Configuration, 125

Models: 5324

1 388

Download 388 pages 31.83 Kb

Page 125

Image 125

Default Configuration

Automatic crossover is enabled

Command Mode

Interface Configuration (Ethernet) mode

User Guidelines

•Mdix Auto: All possibilities to connect a PC with cross OR normal cables are supported and are automatically detected.

•Mdix ON: It is possible to connect to a PC only with a normal cable and to connect to another switch ONLY with a cross cable.

•If MDIX is set to "no mdix", the device works opposite from the "MDIX On" behavior. With this setting you can only use either an ethernet standard cross-over cable to connect to a PC, or an ethernet standard cable to connect to another switch.

Example

In the following example, automatic crossover is enabled on g5.

Console(config)# interface ethernet g5

Console(config-if)# mdix auto

back-pressure

The back-pressureInterface Configuration mode command enables Back Pressure on a given interface. To disable Back Pressure, use the no form of this command.

Syntax

back-pressure

no back-pressure

Default Configuration

Back Pressure is disabled.

Command Mode

Interface Configuration (Ethernet, port-channel) mode

User Guidelines

•Back Pressure will operate only if duplex mode is set to half.

Ethernet Configuration Commands

125

Page 125

Image 125

Dell 5324 manual Syntax Back-pressure No back-pressure Default Configuration, 125

Contents

CLI Reference Guide Aug Contents Using the CLI Address Table Commands Clock Ethernet Configuration Commands Igmp Snooping Commands Lacp Commands Management ACL Port Monitor Commands Rmon Commands Spanning-Tree Commands SSH Commands Syslog Commands Tacacs Commands Vlan Commands 32 802.1x Commands 382 Page Introduction Command GroupsCommand Groups Configures commands related to 802.1x security protocol Configures and reports on Spanning Tree protocolConfigures Tacacs commands Address Table Commands AAA CommandsConfigures the system to automatically switch Configures an external time source forDefines an authentication key for Simple Displays statically created entries in the bridgeConfiguration and Image Files Commands Displays the backup configuration file contents Ethernet Configuration CommandsGvrp Commands Defines a default gateway router Igmp Snooping CommandsIP Addressing Sets an IP addressCache Line CommandsDeletes entries from the host name-to-address Sets the line for automatic baud rate detection Lldp CommandsPHY Diagnostics Commands Management ACL CommandsQoS Commands Port Channel CommandsPort Monitor Commands Enables each port trust state Radius CommandsSnmp Commands Rmon CommandsSpanning Tree Commands MST Sets the default path cost method SSH CommandsOverrides the default link-type setting Syslog Commands Reloads the operating system System Management CommandsTacacs Commands Vlan Commands User Interface CommandsSwitches the mode to debug Disables the default Vlan functionalityInterface Reserves a Vlan as the internal usage Vlan of anWeb Server Commands Command Description Access Mode 802.1x CommandsCommand Groups GC Global Configuration Mode Command ModesDevice Notification operation Sntp IC Interface Configuration ModeReserves a Vlan as the internal usage Vlan of an interface An Extensible Authentication Protocol EAP request/identityFrame, from the client, before resending the request Command Description LC Line Configuration ModeEnables the Simple Network Time Protocol Sntp client on an PE Privileged User Exec Mode MA Management Access-level ModeVlan UE User Exec Mode SP SSH Public Key ModeCommand Modes VC Vlan Configuration Mode W . d e l l . c o m s u p p o r t . d e l l . c o m Introduction Using the CLICLI Command Modes Privileged Exec Mode User Exec ModeExit End Ctrl+Z Global Configuration ModeStarting the CLI Consoleconfig# username admin password smith Editing FeaturesEntering Commands Negating the Effect of Commands Terminal Command BufferCommand Completion Config#interface ethernetKeyboard Shortcuts CLI Command ConventionsItalic font EnterUsing the CLI Aaa authentication login AAA CommandsDefault Configuration Command ModeExample Aaa authentication enableFollowing example configures authentication login Console config# aaa authentication enable default enable Login authenticationConsole config-line#login authentication default Enable authenticationFollowing example configures the http authentication Ip http authenticationConsole config-line#enable authentication default Following example configures https authentication Ip https authenticationShow authentication methods This command has no default configuration Syntax Show authentication methods Default ConfigurationPrivileged Exec mode Following example displays the authentication configurationSyntax Password password encrypted No password PasswordConsole# show authentication methods Following example specifies a password secret on a line Enable passwordNo password is required No user is defined UsernameShow users accounts Console# show users accounts Syntax Show users accounts Default ConfigurationAAA Commands Bridge address Address Table CommandsInterface configuration Vlan mode This example, bridge multicast filtering is enabled Disabled. All multicast addresses are flooded to all portsConsole config# bridge multicast filtering Bridge multicast filteringFollowing example registers the MAC address No multicast addresses are definedExamples No forbidden addresses are defined Command ModesBridge multicast forbidden address Bridge multicast forward-all Disable forward-all on the specified interfaceBridge multicast forbidden forward-all This example all multicast packets on port g8 are forwardedSyntax Bridge aging-timeConsole# clear bridge Clear bridgeSyntax Clear bridge Port security Disabled No port securityInterface Configuration Ethernet, port-channel mode Port security routed secure-address Console config-if#port security routed secure-addressShow bridge address-table Mac-address-Specify a MAC address in the formatPort-channel-number-A valid port-channel number Console# show bridge address-table Show bridge address-table staticConsole# show bridge address-table static Show bridge address-table countSyntax Show bridge address-table count vlan vlan Vlan -Specific VlanConsole# show bridge address-table count Show bridge multicast address-tableConsole # show bridge multicast address-table format ip Console # show bridge multicast address-tableShow ports security Show bridge multicast filteringSyntax Show bridge multicast filtering vlan-id Vlanid-A valid Vlan ID valueConsole # show ports security Clock set ClockClock source Syntax Clock source sntp No clock sourceConsole# clock source sntp Clock timezoneNo external clock source Clock summer-time No authentication key is defined Sntp authentication-keySyntax Sntp authenticate No sntp authenticate Sntp authenticateConsoleconfig# sntp authentication-key 8 md5 ClkKey Following example authenticates key Sntp client poll timerSntp trusted-key Not trustedConsole config# sntp broadcast client enable Sntp broadcast client enableConsole config# sntp client poll timer Sntp client enable interface Sntp anycast client enableConsole config-if#sntp anycast client enable Syntax Sntp client enable No sntp client enable101 Sntp unicast client enableConsole config# sntp unicast client enable Sntp unicast client poll Console config# sntp unicast client pollSntp server Syntax Sntp unicast client poll no sntp unicast client poll103 Show clockSyntax Show clock detail 104 Console# show clockSyntax Show sntp configuration Show sntp configurationConsole# show sntp configuration 105Syntax Show sntp status Show sntp statusFollowing example shows the status of the Sntp 106107 Clock Delete startup-config Configuration and Image FilesConsole# delete startup-config Copy110 Understanding Invalid Combinations of Source and DestinationCopy Character Descriptions Storing the Running or Startup Configuration on a ServerCopying image file from a Server to Flash Memory 111Syntax Boot system image-1 image-2 Boot systemConsole# boot system image-1 112Syntax Show running-config sort type Show running-configSort type defaults to interface if unspecified 113Syntax Show startup-config sort type 114 Show startup-configConsole# show running-config no spanning-tree 115 Syntax Show backup-config 116 Show backup-configConsole# show startup-config no spanning-tree 117 Console# show backup-config software versionSyntax Show bootvar Default Configuration Show bootvarConsole# show bootvar 118Interface range ethernet Ethernet Configuration CommandsInterface ethernet Interface is enabled Syntax Shutdown No shutdown Default ConfigurationFollowing example disables port g5 ShutdownSpeed DescriptionSyntax Description string No description Syntax Speed 100 1000 No speed122 DuplexSyntax Duplex half full No duplex Syntax Negotiation No negotiation Default Configuration Consoleconfig# interface ethernet g5Negotiation FlowcontrolSyntax Flowcontrol auto on off No flowcontrol MdixSyntax Mdix on auto No mdix 124125 Syntax Back-pressure No back-pressure Default ConfigurationBack-pressure 126 Port jumbo-frameClear counters Set interface active Show interfaces configurationConsole# clear counters ethernet g1 Console# set interface active ethernet g5128 Interfaces configuration129 Show interfaces statusConsole# show interfaces status 130131 Show interfaces description132 Show interfaces countersConsole# show interfaces description ethernet g1 Console# show interfaces counters 133Console# show interfaces counters ethernet g1 Following example displays counters for port g1Following table describes the fields shown in the display 134Ieee Std .3, 2000 Edition, section 135136 Syntax Show ports jumbo-frame Default ConfigurationShow ports jumbo-frame Consoleconfig# port storm-control include-multicast Port storm-control broadcast enablePort storm-control include-multicast Console# show ports jumbo-frameConsoleconfig-if#port storm-control broadcast enable Broadcast storm control is disabledDefault storm control broadcast rate is Port storm-control broadcast rateFollowing example displays the storm control configuration Consoleconfig-if#port storm-control broadcast rateShow ports storm-control Syntax Show ports storm-control interface140 Gvrp enable global Gvrp CommandsGvrp enable interface Syntax Gvrp enable No gvrp enable Default Configuration142 Garp timerFollowing example enables Gvrp on ethernet g8 143 By default, dynamic Vlan creation is enabledGvrp vlan-creation-forbid Console config-if#gvrp registration-forbid Console config-if#gvrp vlan-creation-forbidGvrp registration-forbid Clear gvrp statistics145 Show gvrp configurationConsole# clear gvrp statistics ethernet g8 146 Console# show gvrp configurationShow gvrp statistics Following example shows Gvrp statistics information Show gvrp error-statistics147 Console# show gvrp statistics148 Console# show gvrp-error statisticsFollowing example displays Gvrp statistics information Ip igmp snooping Global Igmp Snooping CommandsIp igmp snooping Interface 149150 Ip igmp snooping mrouterIp igmp snooping host-time-out 151 Console config-if#ip igmp snooping host-time-outIp igmp snooping mrouter-time-out Default leave-time-out configuration is 10 seconds Console config-if#ip igmp snooping mrouter-time-outConsole config-if#ip igmp snooping leave-time-out Ip igmp snooping leave-time-outConsole # show ip igmp snooping mrouter Show ip igmp snooping mrouterShow ip igmp snooping interface Example displays Igmp snooping information Show ip igmp snooping groupsConsole # show ip igmp snooping interface 154155 Example shows Igmp snooping informationConsole # show ip igmp snooping groups Igmp Snooping Commands Clear host dhcp IP Addressing CommandsIp address Console# clear host dhcpIp address dhcp Interface configuration Ethernet, VLAN, port-channelNo IP address is defined for interfaces 158Syntax Ip default-gateway ip-address No ip default-gateway Ip default-gatewayNo default gateway is defined 159160 Following example defines an ip default gatewayShow ip interface 161 ArpConsole# show ip interface Clear arp-cache Arp timeoutConsole config# arp 198.133.219.232 00000c400fbc ethernet Show arp Syntax Show arp Default ConfigurationConsole# clear arp-cache Following example displays entries in the ARP tableIp domain-name Ip domain-lookupSyntax Ip domain-lookup No ip domain-lookup Syntax Ip domain-name name No ip domain-nameIp host Ip name-serverNo name server addresses are specified Following example sets the available name serverSyntax Ip host name address No ip host name Clear hostNo host is defined Syntax Clear host nameShow hosts Default Configuration Command ModeSyntax Show hosts name 167168 Lacp system-priority Lacp CommandsLacp port-priority Syntax Lacp port-priority value No lacp port-prioritySyntax Lacp timeout long short No lacp timeout Lacp timeoutDefault port timeout value is long 170Show lacp port-channel Show lacp ethernetConsole# show lacp ethernet g1 statistics Syntax Show lacp port-channel portchannelnumber172 Console# show lacp port-channelLine Line CommandsSyntax Line console telnet ssh Syntax Speed bpsSyntax Autobaud No autobaud Default Configuration Exec-timeoutAutobaud 174Show line Syntax Exec-timeout minutes seconds No exec-timeoutSyntax Show line console telnet ssh 175Terminal history Following example displays the line configurationTerminal history size Console# show line console177 Maximum for the sum of all buffers isLine Commands Lldp enable global Lldp CommandsLldp enable interface SyntaxInterface configuration Ethernet Lldp timerSyntax Lldp timer seconds No lldp timer Default 30 secondsDefault Configuraiton Lldp reinit-delayLldp hold-multiplier Syntax Lldp hold-multiplier number No lldp hold-multiplierSyntax Lldp reinit-delay seconds No lldp reinit-delay Lldp tx-delaySyntax Lldp tx-delay seconds No lldp tx-delay Parameters Default value is 2 secondsLldp management-address Lldp optional-tlvUsage Guidelines No optional TLV is transmitted184 Clear lldp rxSyntax Show lldp configuration ethernet interface Show lldp configurationSwitch# show lldp configuration Show lldp local186 Show lldp neighbors187 Switch# show lldp neighborsSwitch# show lldp neighbors ethernet g1 Lldp Commands Name-The access list name using up to 32 characters Management access-listManagement ACL 189190 Console config# management access-class mlistPermit management 191 Management Access-list Configuration modeDeny management 192 Management access-classShow management access-class Show management access-listSyntax Show management access-list name Console# show management access-list194 Syntax Show management access-class Default ConfigurationConsole# show management access-class Test copper-port tdr PHY Diagnostics CommandsShow copper-ports tdr Console# test copper-port tdr g3Syntax Show copper-ports cable-length interface Show copper-ports cable-lengthPort must be active and working in 1000M 196197 Show fiber-ports optical-transceiverConsole# show copper-ports cable-length Console# show fiber-ports optical-transceiver 198Console# show fiber-ports optical-transceiver detailed 199PHY Diagnostics Commands Console config# interface port-channel Port Channel CommandsInterface port-channel Interface range port-channelChannel-group Console config# interface range port-channelPort is not assigned to any port-channel 202Port channel load balance Console config-if#channel-group 1 mode onShow interfaces port-channel Syntax Show interfaces port-channel port-channel-number204 Default is both rx and tx Port Monitor CommandsInterface Configuration mode Port monitor206 Syntax Show ports monitor Default ConfigurationShow ports monitor 207 Console# show ports monitorPort Monitor Commands Show qos QoS CommandsQos 210 Following example displays a QoS modeWrr-queue cos-map Wrr-queue bandwidth Interface Configuration Ethernet, port channel modeFollowing example maps CoS 3 to queue 211Priority-queue out num-of-queues Following example assigns WRR weights to egress queuesAll queues are expedite queues 212Show qos interface Console config# priority-queue out num-of-queuesFollowing example sets queue 4, 3 to be expedite queues 213214 Qos map dscp-queueConsole# show qos interface ethernet g1 queuing 215 Qos trust GlobalSyntax Qos trust cos dscp No qos trust Syntax Qos cos default-cos No qos cos 216 Syntax Qos trust No qos trust Default ConfigurationQos trust Interface Qos cos217 Show qos mapSyntax Show qos map dscp-queue Console# show qos map Dscp-queue map Following example displays the Dscp port-queue mapFollowing table describes the fields used above D1 x 10 + D2 = Value of DscpBy default, no Radius host is specified Radius CommandsRadius-server host Ip-address-IP address of the Radius server hostDefault is an empty string TimeoutRadius-server key Syntax Radius-server key key-string No radius-server keyRadius-server retransmit Console config# radius-server retransmitRadius-server source-ip 221222 Radius-server timeoutConsole config# radius-server timeout Syntax Show radius-servers Default Configuration Console config# radius-server deadtimeRadius-server deadtime Show radius-serversConsole# show radius-servers Following example displays the Radius server settings224 Show rmon statistics Rmon CommandsConsole# show rmon statistics ethernet g1 225Field Description 226227 Rmon collection historyShow rmon collection history Console config-if#rmon collection history 1 intervalFollowing example displays all Rmon group statistics Console# show rmon collection history229 Show rmon historyConsole# show rmon history 5 throughput Console# show rmon history 5 errors230 231 Console# show rmon history 5 other232 Rmon alarm233 Show rmon alarm-tableSyntax Show rmon alarm-table Default Configuration Show rmon alarmConsole# show rmon alarm-table Syntax Show rmon alarm number235 Following example displays Rmon 1 alarmsConsole# show rmon alarm 236 Rmon eventSyntax Show rmon events Default Configuration Following example configures an event with the trap indexShow rmon events Following example displays the Rmon event tableConsole# show rmon events Show rmon logSyntax Show rmon log event Event-Event index. Range 0239 Following example displays the Rmon logging tableConsole# show rmon log Rmon table-size Console config# rmon table-size historyHistory table size is Log table size is 240There are no default communities defined Snmp CommandsSnmp-server community No snmp-server community community ip-addressDefault and DefaultSuper views exists Default SettingSnmp-server view 242243 Snmp-server filterProduct specific Snmp-server location Snmp-server contactIncluded Syntax Snmp-server contact text No snmp-server contactConsole config# snmp-server enable traps Snmp-server enable trapsSyntax Snmp-server location text No snmp-server location 245Console config# snmp-server trap authentication Snmp-server trap authenticationSnmp-server host 246247 Snmp-server set248 Snmp-server groupSnmp-server user Console config# snmp-server group user-groupv3 priv readNo group entry exists Router context is translated to context in the MIB250 Console config# snmp-server user Following example configures a new Snmp Version 3 userSnmp-server v3-host 251252 Following example configures an SNMPv3 hostSnmp-server engineID local Consoleconfig # snmp-server engineID local default Syntax Show snmp engineID Default SettingShow snmp engineid 253Show snmp Syntax Show snmp Default ConfigurationConsole# sh snmp 254255 Show snmp viewsSyntax Show snmp views viewname 256 Show snmp groupsSyntax Show snmp groups groupname 257 Show snmp filtersSyntax Show snmp filters filtername 258 Show snmp usersSyntax Show snmp users username 259 Snmp Commands Spanning-tree mode Spanning-Tree CommandsSyntax Spanning-tree No spanning-tree Default Configuration Spanning-treeConsoleconfig# spanning-tree forward-time Consoleconfig# spanning-tree mode rstpSpanning-tree forward-time Seconds-Time in seconds. Range 4263 Spanning-tree hello-time264 Consoleconfig# spanning-tree hello-timeSpanning-tree max-age Consoleconfig# spanning-tree max-age Spanning-tree disableConsoleconfig# spanning-tree priority Spanning-tree prioritySpanning-tree cost Following example disables spanning-tree on g5Syntax Spanning-tree cost cost No spanning-tree cost Cost-The port path cost Range 1 200,000,000Spanning-tree port-priority Consoleconfig-if#spanning-tree port-prioritySpanning-tree portfast 267Consoleconfig-if#spanning-tree link-type shared Consoleconfig-if#spanning-tree portfastSpanning-tree link-type 268Console config # spanning-tree mst 1 priority Default number of hops isSpanning-tree mst priority Spanning-tree mst max-hopsConsoleconfig-if#spanning-tree mst 1 port-priority Console config # spanning-tree mst max-hopsSpanning-tree mst port-priority 270Spanning-tree mst cost Spanning-tree mst configurationInterface Long Short 271Instance mst Syntax Spanning-tree mst configuration Default SettingSyntax Instance instance-id add remove vlan vlan-range 272Revision mst Name mstSyntax Name string Syntax Revision value No revisionFollowing example sets the configuration revision to Default configuration revision number isShow mst Syntax Show current pendingSyntax Abort Default Setting Syntax Exit Default SettingExit mst Abort mstSpanning-tree bpdu Spanning-tree pathcost methodConsole# spanning-tree pathcost method long 276Clear spanning-tree detected-protocols Consoleconfig# spanning-tree bpdu floodingSyntax Spanning-tree bpdu filtering flooding 277Console# clear spanning-tree detected-protocols ethernet g1 Show spanning-treeFollowing example displays spanning-tree information 278Console# show spanning-tree 279280 281 282 283 284 285 286 Console# show spanning-tree mst-configuration287 288 289 290 Spanning-tree mst mstp-rstpRoot guard is disabled Consoleconfig# spanning-tree mst mstp-rstpInterface configuration Ethernet, port-channel Spanning-tree guard root292 Following example enable root guard on port g8Consoleconfig-if#spanning-tree guard root Ip ssh server SSH CommandsIp ssh port Console config# crypto key generate dsa Syntax Crypto key generate dsa Default ConfigurationCrypto key generate dsa Crypto key generate rsaConsole config# crypto key generate rsa Syntax Crypto key generate rsa Default ConfigurationIp ssh pubkey-auth 295User-key Consoleconfig# crypto key pubkey-chain sshCrypto key pubkey-chain ssh 297 Key-stringSyntax Key-string row key-string 298 Syntax Show ip ssh Default ConfigurationShow ip ssh Show crypto key mypubkey Following example displays the SSH server configurationSyntax Show crypto key mypubkey rsa dsa Rsa-RSA key Dsa-DSA keyConsole# show crypto key mypubkey rsa Show crypto key pubkey-chain ssh300 Following example displays the SSH public called bob Console# show crypto key pubkey-chain sshConsole# show crypto key pubkey-chain ssh username bob 301SSH Commands Syntax Logging on no logging on Default Configuration Syslog CommandsLogging on LoggingLogging console Default is informationalAs described in the field descriptions Syntax Logging console level No logging consoleLogging buffered Default level is informationalLogging buffered size Syntax Logging buffered level No logging bufferedSyntax Clear logging Default Configuration Console config# logging buffered sizeClear logging Console# clear loggingLogging file Syntax Clear logging file Default ConfigurationClear logging file Syntax Logging file level No logging fileShow logging Syntax Show logging Default ConfigurationFollowing example clears messages from the logging file Console# clear logging fileShow logging file Syntax Show logging file Default ConfigurationConsole# show logging 309310 Syntax Show syslog-servers Default ConfigurationShow syslog-servers 311 Following example displays the syslog server settingsConsole# show syslog-servers Syslog Commands System Management Timeout timeout-The default is 2000 millisecondsPing 313314 TracerouteFollowing example displays a ping to IP address 315 316 317 Special Telnet Command charactersTelnet 318 Keywords Table319 Ports TableResume Following command switches to another open Telnet sessionSyntax Resume connection 320Hostname ReloadConsole# show users Show usersShow sessions Show system Exec modeConsole show sessions Syntax Show systemFollowing example displays the system information Show versionSyntax Show version 324 Console show systemSyntax Asset-tag tag No asset-tag Asset-tagTag-The device asset tag. Range 1- 16 characters 325Show system id Syntax Show system id Default ConfigurationConsole show system id 326Tacacs-server host Tacacs CommandsNo Tacacs host is specified 327Following example sets the authentication encryption key Tacacs-server timeoutTacacs-server key Following example specifies a TACACS+ host329 Console config# tacacs-server timeoutTacacs-server source-ip Syntax Show tacacs ip-address Show tacacsIp-address-Name or IP address of the host Console# show tacacsUser Interface EnableDisable Configure LoginSyntax Login Default Configuration Syntax ConfigureSyntax Exit Default Configuration ExitconfigurationAll command modes 333ExitEXEC Syntax End Default ConfigurationEnd Following example closes an active terminal sessionSyntax History No history Default Configuration Syntax Help Default ConfigurationHelp HistorySyntax Debug-mode Default Configuration Syntax History size number-of-commands No history sizeHistory size Debug-mode337 Syntax Show history Default ConfigurationShow history Show privilege Syntax Show privilege Default ConfigurationConsole# show history Console# show privilegeVlan Vlan CommandsVlan database Console# vlan database Default-vlan disableInterface vlan 341 Interface range vlanSyntax Interface range vlan vlan-range all Name Switchport access vlanSyntax Name string no name 342343 Switchport trunk allowed vlanConsole config-if#switchport access vlan Switchport general allowed vlan Switchport trunk native vlanConsole config-if#switchport trunk allowed vlan add 2,5-8 Console config-if#switchport trunk native vlan345 Switchport general pvid346 Switchport general ingress-filtering disableIngress filtering is enabled Switchport forbidden vlan Switchport general acceptable-frame-type tagged-onlyAll frame types are accepted at ingress All VLANs allowedMap protocol protocols-group Console config-if#switchport forbidden vlan addFollowing example maps protocol ip-arp to the group named 348Ip internal-usage-vlan Switchport general map protocols-group vlanVlan-id-VLAN ID of the internal usage VLAN.Range Valid Vlan 349Show vlan Console config# ip internal-usage-vlanSyntax Show vlan tag vlan-id name vlan-name Following example displays all Vlan information351 Syntax Show vlan internal usage Default ConfigurationShow vlan internal usage Show vlan protocols-groups Syntax Show vlan protocols-groups Default ConfigurationConsole# show vlan internal usage Following example displays protocols-groups information353 Show interfaces switchportConsole# show vlan protocols-groups Syntax Switchport mode customer access trunk general 354 Switchport modeConsole# show interface switchport ethernet g1 No switchport mode Switchport customer vlanNo Vlan is configured Vlan-id- Vlan ID of the customer356 Ip http server Web ServerIp http port Syntax Ip http port port-number No ip http portIp https server Default for the device is disabledIp https port Syntax Ip https port port-number No ip https port359 Following example configures the https port number toCrypto certificate generate Crypto certificate request Console enable# crypto certificate generate key-generateCertificate and the SSL RSA key pairs do not exist Following example regenerates a Https certificate361 Console# crypto certificate 1 requestSyntax Crypto certificate number import Crypto certificate importNumber-Specifies the certificate number. Range 1 362Ip https certificate Consoleconfig# crypto certificate 1 importCertificate number 363Crypto certificate export pkcs12 Console config# ip https certificateSyntax Crypto certificate number export pkcs12 364Console# crypto certificate 1 export pkcs12 Following example exports the certificate and RSA keys365 Syntax Crypto certificate number import pkcs12 passphrase Crypto certificate import pkcs12Following example imports the certificate and RSA keys 366367 Syntax Show crypto certificate mycertificate number Show crypto certificate mycertificateFollowing example displays the certificate Console# show crypto certificate mycertificateConsole# show ip http Show ip httpShow ip https 370 Console# show ip httpsAaa authentication dot1x 802.1x CommandsConsole config# aaa authentication dot1x default none Method1 method2...-At least one from the following tableConsole config# dot1x system-auto-control Following example enables 802.1x globallyDot1x system-auto-control Dot1x port-controlConsole config-if#dot1x port-control auto Dot1x re-authenticationSyntax Dot1x re-authentication No dot1x re-authentication 373Dot1x re-authenticate Dot1x timeout re-authperiodConsole config-if#dot1x re-authentication Console config-if#dot1x timeout re-authperiod375 Dot1x timeout quiet-periodConsole# dot1x re-authenticate ethernet g8 376 Dot1x timeout tx-periodConsole config-if#dot1x timeout quiet-period Dot1x max-req Dot1x timeout supp-timeoutSyntax Dot1x max-req count No dot1x max-req 377378 Dot1x timeout server-timeoutShow dot1x Console config# dot1x timeout server-timeoutSyntax Show dot1x ethernet interface 379Console# show dot1x ethernet g3 380Syntax Show dot1x users username username Show dot1x usersUsername-Supplicant username Range 1- 160 characters Following example displays 802.1X users382 Show dot1x statisticsSyntax Show dot1x statistics ethernet interface 383 Switch# show dot1x statistics ethernet g1Dot1x auth-not-req User should be authorized to access the VlanSyntax Dot1x auth-not-req no dot1x auth-not-req 384Dot1x single-host-violation Dot1x multiple-hostsSyntax Dot1x multiple-hosts no dot1x multiple-hosts 385Forward trap Show dot1x advancedSyntax Show dot1x advanced ethernet interface 386387 Switch# show dot1x advancedSwitch# show dot1x advanced ethernet g1 388 Console# show dot1x advanced ethernet g1